Mereen Johnson 424 DC Gang Rip Outfeed Rollers

These two rip saws were removed from service in working condition some time ago. The seller purchased them and never installed them. They have been in storage the whole time.

Mereen Johnson 424 DC/SR4 Gang Rip Saw with Automated Infeed with multiple lasers manufacturer’s specs to be confirmed 24” width capacity 3-1/2” thickness capacity 75 HP main motor 3 hp feed motor feed rete 30-245 fpm

New Venture Manufacturing Gang Rip Saw Hydraulic Tank (5) Moving Blades Laser Tower Touchscreen Controls This machine has been removed from service. The photos showing the system setup were taken before it was removed

Northtech MRS-12N Gang Rip 50 HP Motor Needs a new safety with on the door

Northteck MRS-14-DXL 460v Manufacturer notes: This is a very popular machine and cost effective. New open ended design allows for you to cut wide material up to 27-1/8? wide. Plus spare arbors, lasers, and the optional quick locking, easy to adjust infeed will not break the bank. The Northtech heavy-duty 50 HP multi-rip (“gang-rip”) saw with 15? maximum blade diameter quickly and accurately cuts material up to 4-15/16? thick and 27-1/8” wide. Cutting both sides of your blanks at once provides incredible parallelism, reducing required moulder allowance, and increasing your yield. Laser guides (one included) and an optional 103” fence make proper alignment of even the longest material simple and precise. Variable feed speeds of 25 – 120 FPM and powered height adjustment further improve operator efficiency.

- Close link chain vs. open (no dust or pinch point) - Oiler has twice the number of lube points (critical) - The VS adjustment location on the 14N. - Can cut up to 4 15/16? with 14? blade vs. the MRS-12 12? blade 3-15/16”. - Can run 12? as well on the MRS-14N - Bottom kickback fingers for added safety - Saws, with proper tooling and material, can glue line Specifications: - Main Motor Hp. = 50 Hp. - Voltage/ Freq. = 460 Volt 60Hz - Phase = 3 Phase - Amp Requirement = 35 Amps - Feed Hp. = 2 Speed 1.5 / 3 Hp. - Feed System = Feed Chain - Feed Speed = 25 – 120 FPM - Variable Speed = Variable Speed Pulley - Elevation Hp. = 1/4 Hp. - Elevation Style = Manual Wheel Adjustment - Elevation Sys. = Jack Screw / Linear Guides - Total Hp. = 53.25 Hp. - Electronics = CE Approved Components - Dual Voltage = Elevation Arbor Motors - Control Voltage = 110 Volt - Assisted Start = Wye-Delta - Pass-Line = 33-1/2” - Min. Length = 17-3/4” - Min. Width = 1/2” - Max. Width = 27-1/8” - Min. Thickness = 5/16” - Max. Thickness = 4-15/16” - Arbor Rpm = 3570 Rpm - Blade Size = 12” Tungsten Carbide Tipped - No. of Teeth = 36 Tooth - Blade Kerf = 3.5 mm - Cleaning System = Brush on Chain - Vertical Travel = 3/8” – 5” - Dust Collection = (2) 6” @ 1962 CFM - Arbor Diameter = 70 mm - Hold Down Style = Pressure Plate - Kickback Finger = (2) Top (1) Bottom Sets - Emergency Stop = Push Button - Rear E Stop = Push Button - Safety Feature = Safety Interlock Switch - Guarding = Full Cabinet Enclosure - Oiler = Automatic Mechanical Oiler - Low Oil Warning = Low Oil Shut-off - Fence Type = Adjustable - Fence Dims. = 103” Length - Frame Const. = 5/16” Steel Construction - Worktable Dims. = 27-1/8” x 64” - Infeed Table = 13-3/4” x 103” - Decible Rating = 74 dB - Net Weight = 4402 Lbs. - Gross Weight = 4694 Lbs. - Machine Dims. = 67” x 58” x 71” - Packaging Dims = 72” x 65” x 77”

Paul AB920 Rip Saw Scanning Fenceless Infeed Infeed & Outfeed (not including decks) The machine has one fixed and 2 moving blades. The minimum distance between the moving blades is 44 mm (1.73"). The maximum distance between the moving saw blades is 210 mm (8-1/4"). The machine is designed for incoming boards with the following min./max. dimensions Length: 4' - 16' Width: 2" - 19" Ripped widths: 1.75" - 8" Thickness: 1" - 2" 480 Volt, 60 hz., 3 phase electrics 75 HP main motor Automatic edging separation after the saw Feed speed up to 300 fpm Fenceless infeed system with automatic skewing capability 16 width sensors on the infeed system

This machine was reported to be in running condition when removed from service. Looks like a Pendu. Cannot find a plate on the machine to confirm. this is a single arbor gang and it does not have a sizer. 75 HP Main Motor 5 HP Drive motor

Powermatic SLR12 Straight Line Rip Saw

Raimann KM310M Rip Saw 2 Moveable Blades

Raimann Unirip 310 Gang Rip

Raimann KM310M Rip Saw ValuRip Infeed System One moving Blade

Raimann KM310 Rip Saw Per seller: The saw runs material. The variable infeed is stuck on one speed.

Raimann UniRip 310 Rip Saw Misc spacers and blades Bought new in 2020

SCMI M3 Rip Saw Still under power for inspection

SCMI M3 Gang Rip Saw Includes: Misc blades

Shurman Double Arbor Gang Saw 12" Capacity Thin Kerf Babbit Grinder

Silver Straight Line Rip Saw 15 HP Motor

It is a 2 saw re-rip with one moveable saw and an adjustable fence. Capacities: Minimum length = 8” Maximum length = 192” Minimum width = 1 ½” Maximum width = 6” Minimum thickness = 7/8” Maximum thickness = 1”