Nicholson Flat Drum Chipper 9'5' x 55" Includes: Trailer, AC power, belt conveyor, switch gear option. System chipped just over 120 truckloads

Complete Chip Mill that is ready to be moved System includes: - Log Deck - Log Singulator - Control Room - Nicholson A5 Debarker - Peeled Log Outfeed Bin - Reclaim Log Infeed Deck - Bark conveyor and stacker - Bark Shredder - Progress 84" 6 Knife Chipper w/ 600 HP Motor - Progress Chip Screen: 7'x14' - Chip Blower and Truck Loading Conveyor - MCC Center

2011 Peterson Pacific Horizontal Grinder Power Source: Diesel Engine Mfr: Cat Engine Model: C27 Horsepower: 1000 Has approximate 9050 hours

Complete Player Design Drying System - (2) Touch Screen Controllers - (1) PLC Control Box - (1) 12’ X 20’ Burner – 25 million BTU capacity with tempered sight glass that can run green chips/dust - (1) Burner Auger , Gearbox, and Motor - (1) Burner Blower Fan Assembly and Motor - (1) Player Single Pass Insulated Dryer Drum (12x50), 8” T section track, 28” Trunnions, Drive lubrication system, Sprocket, Chain and Gearbox / Motor (Drum rated for output material volume of 16,000 lbs per hour) - (1) Air Pro 48” Overhung Fan Assembly (ID Fan) (No Motor) ---- (Part# 12113601, Type-IERS615, Serial# 21136,) - (1) 200 HP motor for ID Fan - (1) Beck- Damper Adjustment Arm/Gearbox (ID fan comes with opposed blade inlet damper with a 300 ft-lb Beck actuator and armature) ---- (Model 11-209-155212-04-01---- 120V 1PH / 110VA ) - Piping and dampers for piping - Missing approximately 20’ of Dryer Drum Discharge piping - Missing approximately 20’ of Dryer Drum Recycle piping - System was rated at approx 9.25 Tons/hour

Precision 58" Chipper - Model 58-60-16 6 Knife 150 HP Motor

Complete chip plant includes: - The infeed is 12’ above ground level. They were feeding it one log at a time with a shovel. - There is a single chain 12” wide leading to the debarker. - The debarker is a Salem 20” ring debarker with mcdiarmond controls. - From the debarker it goes through I think is a metal detector. It’s is enclosed, 8’ long with a belt conveyor. - 75’ of 3-strand chain that reduces to 2-strand chain for 35’ then goes to another 2-strand chain for 12’ then goes into the chipper. - The chipper is a Precision with 2- 400 hp high efficiency 3 phase motors. - From the chipper the chips drop onto a 42”x50’ inclined belt that leads to the 2 deck screen. The screen is 92”x20’ - The waste goes on a 9”x20’ incline belt and dropped into a truck. - The chips go out on a 3-strand 100’ conveyor (strands are 14” wide) to a radial stacker for loading trucks. The stacker belt is 42”x65’ - Chips can be redirected to blower unit system that will transport them to a rail siding to so they can be loaded into a rail area. It starts out with 75’ of 12” pipe running on the ground. Then it sweeps straight up to a height of about 24’ and goes 150’ to a siding across the county road. The chip loading facility is intact. - The hog is located back by where the logs are loaded onto the chain going to debarker. Here’s a list of the conveyors going back to the Kockums hog. It has a 24”x36” opening at the top. - Conveyors: 12”x100’, 12”x 25’, 12”x60’. All of these conveyors are 1 strand steel.

The seller has confirmed that this 96" Precision chipper is in good working/running condition and is ready to load. This was not heavily run. This came out of a chip plant in WA. Model 96.27 - Horizontal feed - Side discharge - 4-Knife whole log chipper - 8" thick chipper dissc - Built in disc brake - Extended front shaft for hydraulic starter - Hydraulic starting motor - Side discharge pipe with motorized outlet adjustment - 27" maximum log diameter - Many spare parts and knives included - Average production rate: 125 tons per hour - No hydraulic pump - No motor - an 800HP one can be added for additional cost though... The photo's show the optional extended shaft and hydraulic starting motor which is a special feature....

Precision 10'x20 Screen 3-Decks: 3/4” top deck, 1/4” middle deck screen

Precision 55 screener, was working when pulled out of production.

Precision Disc Scalping Screen Model PDS648 48” wide x approx 8’ long 6 shafts and the discs are stitch welded on

SPECIFICATIONS: - Chip Capacity: 50 LBS/HR - Puck Size: 2? - Chamber Size: 16? X 6? - Puck Exit Conveyor: 6' X 6? - Approximate Floor Space: 5’8? LR X 4' FB X 6’2? H - Electrics: 480 Volt, 3 Ph, 60 Cyc Allen Bradley Panelview 300 Controller

Excellent condition Less than 6 hrs on machine

Rethceif HC2020 Bagging Line Robot stacking system Available approx Spring 2024 Automatic FFS system, ( Sealer, Perimeter Guard, Film Unwind, and Form Tuber) Electric infeed augers 100 HP Hydraulic Motor with Dual Pumps Tower Plunger Gate. Pre Weigh Feed Gate 30’ Long x 16” Diameter Incline Auger.

Rotex 6' x 16' Chip Shaving Screen

Rotex HICAP 2100 Chip Screen

Rotochopper MC256 3126B 300 Hp CAT Engine Dust Control 60 Teeth Roto902 8 row rotor 3/4 x 2 1/4 bolts 3 button remote-Elec Sol Model EL24VRT Drive Belt BL10/5V1600 Square D buttons on 3 button box 24 Volt System Radiator PreCleaner CAT radiator CAT Alternator 9X7803 Turbo II 68-6 intake S/N 87384 DT motors w/case drain Hyd Screen changer Hyd Valve Ass'y Hyd Actuator Hyd powerfeed shock kit Magnet Long Conveyor Pintle Hitch 3 15/16" FAG main rotor bearings Smooth underrotor belt R2 lacing 3/8" steel infeed belt 2 7/16" bearings and shaft on infeed Slab ramp w/blocks No flip down sides on infeed AW68 hyd oil Gruber Welding fuel & oil tank BEE70 omega coupler 3/4" baffled screen Will need to be moved on a trailer.

RUF RB440 Briquette Press (2) Systems available

RUF Briquette Press More info coming!

Schutte model 280.100 Hammer Mill Includes: 125 HP Motor - 480v Includes: (3) Screens: Approx 1", 3/4", 3/8" (to be confirmed) Includes: Stand

Soderhamn 48" Chipper M671 Diesel Engine Mounted on trailer