Weeke BHP 007/430 CNC Router 13 HP HSK 63F Spindle with air blast nozzles 8 Position Rack Style ATC 7 Spindle Boring Block 4x8 Table Part location pins (2) Becker 7 HP vacuum pumps Woodwop Light Barrier safety system

The Vantec 2800mm Spindleless Veneer Lathe is designed to process veneer for plywood production from both hard and soft logs. Its metal tempered grooved rollers and lathe knife inclination system work perfectly to make sure there will always be a precise contact area between the lathe knife and the log during the peeling process by eliminating vibration that could cause damage to the Veneer sheets. Vantec Spindleless lathe proves its efficiency by delivering consistent thickness variation and a impressive top linear speed of 180 m/ min throughout the peeling process for face or core veneers with smooth surfaces. - Log diameter up to 600 mm; - Max log length: 2750 mm; - Min log Length: 2300mm; (with stacker) - Min log length:1800mm (no stacker); - Veneer thickness: 1.0 to 4.0 mm; (Pine and eucalyptus); - Log core after peeling: 40 to 45mm; - Maximum linear speed 180 m/min; - Drive panel included; - Each motor is individually connected by a Variable Speed Drive for torque control in two points of traction on the rollers to pre- vent excessive load on tip ends; - Log Central aligner with maximum of 2200 mm of movement; - Pneumatic scriber Knives (02 fitted on the sides to cut in width and 01 in the Center to cut the length); - Width: 7640 mm; - Length: 3400 mm; - Height: 2550 mm; - Approximate weight: 14000 kg.

The Vantec Automatic Rotary clipper is designed to clip 2800 mm veneer sheets into specific sheet sizes as per the auto stacker preselection. It comes with electronic drive panel, automatic gauge system, positioning of clipper knife by Servomotor and encoder. It is de- signed to work with one tensioned clipper knife with gear motor. It also comes with a 2 HP motor on the output. The clipper knife is not included. - Veneer Thickness : 1 to 4 mm; - Max. Log: 2.750mm; - Minimum veneer width cut: 800 mm; - Max. Veneer length cut: 2700 mm; - Min. Veneer length cut: 700 mm; - Min. Venner rounding length: 150 mm; - Rotor gear motor: helical gears; - Clpper rollers power drive: 4 hp 6P; - Outlet conveyor Motor: 2hp 4P (input) 1 hp 8P (output); - Clipper Servomotor: 40 Nm (2x); - Width: 4800 mm; - Length: 6000 mm; - Height: 1700 mm; - Approximate weight: 7.000 kg

The Vantec Veneer Auto Stacker, ELV 1.82B is a Vacuum stacker for 2800 mm Veneer lathe. It is fitted with double stacking system (04 bins), with four veneer transport lines and four 5hp exhausters. with of two stoppers and eight ejecting arms. With drive Panel, VSD for exhaust fans and hydraulics lifting tables. Min veneer sheet length sheet: 2300 mm; • Max veneer sheet length sheet: 2700 mm (or Two sheets of 1350mm); • Min veneer sheet width: 800 mm; • Max veneer sheet width: 1500 mm; • Max height of stacks: 1000 mm; • Exhaust motor: 10 hp 4P (8x); • Inlet conveyor motor: 2hp 8P; • Transport conveyor motor: 6hp 4P; • Hydraulic pump motor: 5hp 4P (3x);

The Vantec Wood Wast Drum Chipper is used to produce chips from logs and veneer waste. It has a roller infeed system, rubber conveyor belt and hydro-pneumatic unit to lift the rotor for maintenance. Manufacturer specs: - Width of inlet: 600 mm; - Height: 200 mm; - Rotor diameter: 600 mm; - Toothed roller: 01 upper and 02 - lower; - Grooved rollers: 01; - Rollers gear motor: GD (helical - gears); - Upper Rollers motor size: 5 hp; - Upper Rollers motor size: 5 hp; - Feed speed: 40m/min; - Number of rotor knives: 02; - Wood chip size: 30 - 40 mm; - Chipper screen: size: 65 x 65mm - Main motor 100 hp 4P: Included; Drive panel: Included; - Estimated production: 38 m3 / h (it may vary according to the type of material and time used with blade sharpening); - Infeed conveyor length: 3 500 mm (included); - Width: 1 650 mm; - Height: 1 .000 mm; - Overall length: 5800 mm; Approximate weight: 2,900 kg.

This Wood Drum chipper PT600 is used in production of wood chips from logs and veneer waste. It has a toothed roller system that allows efficient material infeed, a rubberized conveyor belt and a Hydropneumatic unit to lift the rotor cover for maintenance. It comes with 01 chipper Knife set and 01 nose bar set. It does not come with the output conveyor. - Width of inlet: 600 mm; - Height: 300 mm; - Rotor diameter: 800 mm; - Toothed roller: 01 upper and 01 lower; - Grooved rollers: 01; - Rollers gear motor: GD (helical gears); - Metal detector: Flat model; - Rollers motor size: 5 hp (2x); - Number of rotor knives: 02; - Wood chip size: 25 - 40 mm; - Main motor 125 hp 4P: Included; - Drive panel: Included; - Lead Time: 240 Days; - Estimated production: 55 m3 / h (it may vary according to the type of material and time used with blade sharpening); - Infeed conveyor length: 3 500 mm (included); - Width: 1 850 mm; - Height: 1 .150 mm; - Overall length: 6 700 mm; - Approximate weight: 4,900 kg.

This Wood Drum chipper PT750 is used in production of wood chips from logs and veneer waste. It has a toothed roller system that allows efficient material infeed, rubberized conveyor belt and Hydropneumatic unit to lift the rotor cover for maintenance. It comes with 01 chipper Knife set and 01 nose bar set. It does not come with the output conveyor. Width of inlet: 750 mm; • Height: 300 mm; • Rotor diameter: 800 mm; • Toothed roller: 03 upper and 03 lower; • Grooved rollers: 01; • Rollers gear motor: GD (helical gears); • Upper Rollers motor size: 7,5 hp (2x); • Feed speed: 35 m/min; • Number of rotor knives: 02; • Wood chip size: 25 - 40 mm; • Chipper screen: size: 70x 70mm; • Main motor 200 hp 4P: Included; • Drive panel: Included; • Estimated production: 65 m3 / h (it may vary according to the type of material and time used with blade sharpening); • Lead Time: 240 Days • Infeed conveyor length: 3 500 mm (included); • Width: 2 500 mm; • Height: 1.250 mm; • Overall length: 7 300 mm; • Approximate weight: 8 750 kg.

This Drum chipper is used in production of wood chips from logs and wood residues (slabs, board off cuts, veneer waste). It has a toothed driven roller system that allows an efficient infeed of the material, rotor with interchangeable thread locks and with a disposable steel plate in the front of the rotor, hydraulic nose-bar/anvil extractor, infeed conveyor with rubberized belt and hydro-pneumatic unit to lift the chipper/rotor lid. (maintenance). It comes with 01 set of blades and 01 nose-bar/anvil. Does not come with outlet conveyor. - Inlet width: 1000 mm; - Nominal chip size: 23 - 30 mm; - Inlet Height: 450 mm; - Main Motor indicated: 300 hp 4P (2x); - Rotor diameter: Ø 1000 mm; - Soft starter drive panel; - Shaft diameter: Ø 220mm; - Metal detector; - Toothed roller: 03 upper and 03 lower; - Estimated production: 130 m3/ h; (may vary according to the type of wood and the sharpening period of the knives); - Roller diameter: Ø 353mm; - Diameter of roller shafts: Ø 100mm; - Chipper Screen: 65 x 65mm; - Grooved roller: 01; - Infeed conveyor length: 5000mm (included); • Driven roller gearmotor: (helical gears); - Width: 3 500 mm; - Driven rollers motor: 15 hp (2x); - Height: 2 100 mm; - Main motor belt: Torque-Team; - Total length: 10 500 mm; - Inlet conveyor speed: 40 mL / min; - Approximate weight: 22 700 kg; - Number of rotor blades: 03;

12'x42' Triple Pass Drum 20 MM BTU Webb Burner Burner feed bin Burner blowers Blower to pull shavings through drum Cyclone BMM 3-level Shaker Screen (2) Outfeed Conveyors Electrical controls

Heil 10.5' x 32' Triple Pass Drum Dryer 1. Jackson Harvester Burner 24 million BTU 2. Fuel Bin 3. Pipe and fan from fuel bin to burner 4. Air lock on dryer 5. 8 X 24 3 pass dryer 6. Trunnions 7. Fans to dryer 8. Pipe to cyclone 9. Cyclone 10. Pipe to fuel bin 11. Fan moving sawdust to fuel bin 12 Hog with 200 HP motor 13 Dust collection system

Heil 10'x40' Triple Pass Drum Dryer Trunions Drum is ready to load.

Hemple CL-8 Wood Turning Lathe 20” capacity will turn to 1/4” diameter manyal feed but auto cycle up to 400/hour 220 volt 3- phase

Hemple CL-8 Wood Turning Lathe 20” capacity will turn to 1/4” diameter manyal feed but auto cycle up to 400/hour 220 volt 3- phase

Hemple CL-8 Wood Turning Lathe 20” capacity will turn to 1/4” diameter manyal feed but auto cycle up to 400/hour 220 volt 3- phase

High Tech 20' Trim Saw (10) Blades

High Point 12" Resaw with Return Conveyor

Single Head Horizontal Band Re-saw System Model : HP-11P-SMART • Single saw head configuration. • Motor powered set works for accurate saw wheel elevation. • Digital position controller permits accurate saw wheel height positioning. • Automatic blade tension is controlled by hydraulic cylinder. • Variable feed speed by hydraulic motor drive. • The big pressure roller is air cylinder loaded to hold wood down firmly. Specifications HP- 11P-SMART 1. Saves Time and labor costs 2. Pneumatic pressure roller infeed 3. Digital position controller permits accurate saw wheel height 4. Easy to operate and set up Feed speed: 4-27m/min (13-90FPM) Max. cutting height: 250mm (10”) Max. cutting width: 300mm (11 3/4”) Min. workpiece length: 400mm; 205mm with extension set Max. workpiece length: 580mm Distance from blade to conveyor: 4-125mm Saw wheel Diameter: 711.5mm (28”) Saw wheel width: 22.7mm (1”) Saw blade size: 4265 x 27mm (168” x 1’) Blade speed: 2816m/min (9240FPM) Saw Motor: 15kW(20HP) Feed unit: 0.75kW(2HP) gearbox motor with frequency converter Cooling system Oil mist Blade tensioning Hydraulic system Motor for blade positioning: 0.18kW(1/4HP) Dust post: Ø4” x 4 Table height: 902.5mm Machine weight: 951kgs Machine dimensions: 2835 x 2052 x 1678mm (LxWxH)

Hoffman PU2

2003 Holytek HK-610 Double Sided Planer 24” x 8 “ Capacity 30 HP Top head/15 HP bottom head 3HP Feed Motor - 19.5 -88 FPM 460 Volt 3-Phase

Holzher 1265 Super Cut Panel Saw