MLS Number 12231702 2011 Clarke's Industries Bag House ? Explosion doors ? Abort gate at outfeed ? Abort gate at infeed ? Backdraft damper at infeed ? Spark detectors on infeed and outfeed lines ? Airlock ? Backdraft Damper on dust outfeed line ? Deluge System This baghouse is fed from a fan that has suction from Edger, 6”-10”-12”-20” Ukiah (chip/saw) and 20” sawbox. The sawdust from the discharge line under the airlock of the baghouse is sucked into Discharge blower (See Item#2). The dust outfeed line at the middle of baghouse, which discharges the dust fines during the cleaning cycle of bags, returns the fines to the baghouse fan. The Baghouse supplies air back into the building. This baghouse is fed from a fan with following specs: OEM & Model: Clarke’s Industries, Model MH-11, Serial 11OCWUBI3923 Driver: TECO 350 HP, 1785 RPM, 5009C Frame Motor Capacity: 66000 CFM Spark Detection Control System OEM/Model: Clarke’s Industries, Pyroguard CXC-2 Buyer responsible for dismantling.

Cresswood Model EF 50-100A Horizontal Shredder 100 HP 12' Vibratory Conveyor (2) Feed Rollers Screw Auger Discharger Inclined Conveyor with 10" Magnetic Head Pulley Discharge Height 116" Crossbelt Magnet Soft Start Extra Set of Cutters 2 New Screens 1/2" Screens

?Cresswood EF-60 Grinder 100 HP 60” Wide Feed Opening Includes 60”W Vibrating Conveyor (shaker table)

2017 Diamond z 4000 horizontal grinder -Approx 7,500 hours and will go up. Used daily -New discharge belt -765hp c18 -Wireless remote -Comes with 1-1/2" Screens, 3"x5" Screens, spare main hydraulic pump and misc parts

MLS Number 10682943 DIEHL SL52 STRAIGHT LINE RIP SAW Bottom arbor 4-1/4"X8-1/2" capacity 15 HP 3,545 RPM arbor drive motor Infeed speed up to 200 FPM Serial# 10/88M-5312-4728 Voltage: 460/60/3 phase Amps: 21.7 Wiring diagram # 2-9000-0026 Was removed from service in November 2020

DIEHL 990 GANGRIP SAW Product No. 1001 30 HP - 3600 RPM arbor motor-AB size 4 starter-110 volt controls 12 " arbor width with 3-1/2" maximum thickness 8 roll feed - 4 top (powered) - 4 bottom Anti-kick back fingers : top and bottom One (1) saw cartridge-2 3/4 " saw blade bore New arbor bearings 5 HP feed: single speed Rip fence Outboard bearing on arbor 3" throat capacity to 1st saw blade Cleaned, painted and checked Serial # : 54174 Year: 1958

Diehl SL50 Straight Line Rip Saw 240 volt 3 phase Variable speed control SN: 51108

Diehl model MR-90 Gang Rip Saw Twelve ( 12 ) inch saw arbor width capacity- Roll feed 50 HP 3600 RPM arbor motor -direct coupled wired 480 volts, 3 phase- new motor bearings 2 HP variable speed feed motor 50 to 150 FPM feed speed-variable Four powered top feed rolls- Excellant feed roll gears 12 inch arbor with one (1) sleeve with spacers Adjustable rip fence Serial number : 66M-1668 Cleaned , checked , and painted

MLS Number 10689968 Globe 5 Head Panel Trim Saw Approximate panel capacity: 8 feet wide X 26ft long Saw was cutting large full size sheets (8ft+ x 26ft) at a particle board manufacturer Lugs on chains have micro adjustment bolt ( brass) Air cylinders raise and drop heads Brands of chain: Woodward & White Overall width: 14 ft. 6inches Overall height: 6 ft. Overall length: 33 ft. 4 inches+-

MLS Number 12543674 Hazlethorn Stake Pointer 240V single phase Air operated control Needs new cutters

Ingersoll Rand Air Compressor 3 phase 10 hp Work ready

54" Horizontal Resaw Wide Blade Excellent Machine 400K Replacement Cost

MEREEN-JOHNSON 424 DC GANG RIP SAW 24 inch width capacity 75 HP arbor motor- 3600 RPM direct drive 5 HP variable speed feed ( new belt ) Four ( 4 ) kick-back finger sets : ( Two ( 2 ) top in-feed, One ( 1 ) bottom in-feed, One ( 1 ) top out-feed ) A new out-board arbor bearing assembly New set of alum bars and rubber slats installed It is wired 480 volts 3 phase . The serial no. is MJ-4709 One saw sleeve and set of spacers ( 6 saw blades ) Cleaned, painted, and checked.

2018 Morbark 3400XT Wood Hog Horizontal Grinder CAT C18, 765 Hp engine Approx 2100 hours New belly belt/skirting; Rebuilt mill Engine has new cylinder sleeves with rod & main bearings, purge pump & hydraulic fan motor (replaced by manufacturer due to a defect) Remote Magnet 1” & 5” screens Great machine and ready to go to work

Morbark Chip Blower Hopper Feed Came out Running 10 HP Motor

2022 Morbark 3000XT Horizontal Grinder -180 hours -575 hp CAT engine -Remote -Still under warranty NEW NEW NEW

Murphy Rogers MRM-16-185H Shaker Dust Collector 16” dia. inlet 25 hp exhauster motor 81 filters 6” dia. x 68” lg 668 sq/ft of filter 6,000 cfm estimated capacity Serial Number: 1020

8 Head Drop Saw 40' x 14' 5 Strand lumber Deck (Infeed) 16' x 5' 5 Strand Lumber Deck (Infeed) 16' x 5' High 8 Strand Unscrambler (Infeed) 100' x 24" Scrap Conveyor (Outfeed) Drag Chain Underneath (Outfeed) 24" Roll Case (Outfeed) Electric Disconnects And Controls Optional 4 Strand Roof Top Transfer Optional 82' Of 5 Strand Lumber Dcck

MLS Number 10908375 Newman S-282 Wood Planer Used 18 x 16 S-282 Newman Serial number 14467 Helical 6 knives Length 18” Top head 40 Hp Bottom head 25 Hp 15 Hp HPU Voltage 460

Newman 282 Wood Planer 18 inch wide planning capacity by 6 inch thickness Newman 6 row Quite-cut carbide cutterhead 50 to 75 percent carbide knife life remaining 40 HP 3600 rpm top head motor-DMD 25 HP 3600 rpm bottom head motor- DMD 15 HP hydraulic pump package Feed speeds : 40 to 150 feet per minute Rubber tire feed – one row in-feed and one row out-feed. Dust hood Carbide knife grinder and jointer Cleaned and tested