DELTA 11-990C 12" 5-Speed Bench-Top Drill PressSpecifications: -- Table size 8-1/2" x 8-1/2" with 15-1/2"; x 40"; x 11/16"; Thick Plywood top, Table tilt 40° Left/Right. -- Base size 8-1/4" x 8-1/4". -- Quill travel 2-3/8", Chuck capacity 1/2", JT33 Spindle taper. -- Spindle speeds 620, 1,100, 1,720, 2,340, & 3,100 RPM.Equipped with: -- 1/3 HP - 1,720 RPM Motor.Complete with: -- Portable Wood Cabinet.Dimensions with cabinet: 41" x 36" x 57" H

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i56 DELTA 14" Bench-Top Drill Press Specifications: Table dia. 10" x 10". Base size 7" x 9-1/2". Quill travel 3-1/2". Equipped with: 1-1/2 HP - 1,740 RPM Motor.

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i54 ROCKWELL/DELTA 17-600 17" Variable-Speed Floor-Type Drill Press Specifications: Table size 11" x 14". Base size 10" x 13-1/2". Quill travel 5". Spindle speeds 350 - 4,250 RPM. Equipped with: MT2 Spindle taper. 1 HP - 1,725 RPM Motor.

Electric Single Spindle Pocket Drill. Specifications: -- Capacity: Materials from 1/2"- to 1 1/2"-thick. -- 1.5 HP direct drive electric motor (also available 1.5 HP direct drive pneumatic motor); 40" table top working height; 1 Sec cycle time. -- Drills the pocket hole with a 3/8" dia. step bit in (1) smooth operation. The bit is supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material. -- Electrical: 110 VAC, Pneumatics: 90 PSI, recommended for clamping. -- Dimensions: 50"H x 24"W x 24"D (40" table height), 176 lbs.Features: -- 15° Boring angle for greater stability, reduced screw breakout & splitting. -- This produces a smaller "flat bottom" pocket hole with rounded sides that can be plugged with a dowel if desired. Includes: -- Pressure gauge & cycle counter, fence, holddown tower, (1) 3/8" cobalt drill bits, and foot pedal actuation.

Pneumatic Single Spindle Pocket Drill;Specifications: -- 1.25 HP direct drive pneumatic motor; 40" table top working height; (0.5 - 1) Sec cycle time. -- Drills the pocket hole with a 3/8" dia. step bit in (1) smooth operation. -- The bit is supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material. Pneumatics: 120 PSI recommended. Features: -- 15° Boring angle for greater stability, reduced screw breakout & splitting. This produces a smaller "flat-bottom" pocket hole with rounded sides that can be plugged with a dowel if desired. Includes: -- External regulator, filter & lubricator, (1) 3/8" cobalt drill bit, and foot pedal actuation. Just add $150 to the price of the machine for shipping.

Pneumatic Single Spindle Tabletop continuous operation drill;Specifications: -- 1.25 HP direct drive pneumatic motor; 8" tabletop working height; 1 Sec cycle time. -- Drills the pocket hole with a 3/8" dia. step bit in (1) smooth operation; the bit is supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material. -- Capacity: Materials from 1/2"- to 1-1/2" thick.Features: -- Pneumatic drill motor, pneumatic clamping. -- 15° Boring angle for greater stability, reduced screw breakout & splitting; this produces a smaller "flat-bottom" pocket hole with rounded sides that can be plugged with a dowel if desired.Includes: -- External regulator, filter & lubricator, 3/8" cobalt drill bit, and foot pedal actuation.Requires a compressor able to produce 8 CFM at 120 PSI (50% duty cycle).

KREG DK 3100 Pocket Hole Boring MachineElectric 3-spindle Pocket Drill; 1.5 HP direct drive electric motor; 39-1/2" table/ top working height; (0.5 - 1) Sec cycle time. -- Drills (2) pocket holes in (1) machining cycle across rails of varying widths with 3/8" dia. step bit in (1) smooth operation.... Drill spindles in the machine are fixed at 3/4" - 1" and 1-3/4" on center allowing it to handle most common rail widths of 1-1/2" up to 3-3/4" with ease. -- One of the (3) Spindles is with left-handed, simply remove one bit from the spindle not being used to set the desired 2-hole spacing. -- The bits are supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material. -- Features: 15° Boring angle for greater stability, reduced screw breakout & splitting. This produces a smaller "flat-bottom" pocket hole with rounded sides that can be plugged with a dowel if desired. -- Includes: Pressure gauge & cycle counter, fence, holddown & clamping assembly, (2) 3/8" cobalt drill bits, and foot pedal control.

NOVY 1872V Multi Spindle Vertical Boring Machine 12 Spindles Vertical boring machineSpecifications: -- Table Hardwood 18" X 72' -- Table stroke 0"- 6" -- (12) Spindles in line at 5" center to center, spindle nose with 0" to 1/2" chuck -- (2) drive motor 2 HP with magnetic starter -- (4) Spring loaded hold down -- Savety guard -- Foot swtich

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i55 ORBIT OR-1758F 17" 12-Speed Floor-Type Drill Press Specifications: Actual throat 8-1/4". Table dia. 11-1/2". Base size 8" x 8". Quill travel 4-1/2". Chuck capacity 5/8". Spindle speeds 250, 380, 450, 550, 650, 800, 1,110, 1,280 1,420, 1,800, 2,000, & 3,100 RPM. Equipped with: MT2 Spindle taper. 1-1/2 HP - 1,725 RPM Motor.

SICOTTE - T 1050, ...Horizontal Boring Machine 2-Spindle Horizontal Borer.Equipped with: -- 1 HP Motor, timing belt drives with motor starter. -- (2) Horizontal spindles, 2" dia. with Jacobs® Chuck, 0 - 1/2" capacity, turning at 3,450 RPM.Features: -- 4" Boring head stroke with air/oil system and adjustable feed speed. -- Spindle mount on dovetail beam with min. 2" to a max. 11-3/4" center distance.Complete with: -- (2) Pneumatic holddowns & 12" x 16" wooden table size.

SICOTTE - Airbor 700-6, ...Vertical Boring Machine18" x 72" Table; variable air/oil feed table; up to 6" adjustable stroke.Equipped with: -- (3) Vertical 2" dia. spindles with Jacobs® Chuck, 0 - 1/2" cap.; spindles fully adjustable to entire table surface and can be as close as 2" center-to-center; spindle speed of 3,600 RPM. -- (3) 2 HP - 1,800 RPM motors, each motor timing belt drive mounted on a cast iron base with eccentric locking mechanism and a cast iron arm that has 18" of adjustment.Complete with: -- (2) Air loaded holddowns. -- (1) Foot switch for boring cycle. -- Includes Safety shield.

SICOTTE J 20-5 Horizontal Boring Machine:12" x 60" Steel table with 2-1/2" manual up-and-down adjustment. -- (4) Drive groups with 1-1/2 HP - 3,500 RPM drive motor each, timing belt & pulley drive. -- (7) Spindles, 2" in dia. and with Jacob chuck 0 - 1/2" capacity. -- Spindle feed powered by 3 HP hydraulic pump, 0" - 6" stroke, variable speed up to (30) strokes/Min.Complete with: -- (3) Pneumatic holddowns, -- Cycle timer 0-30 sec., -- Automatic/manual cycle with foot pedal switch, -- Sinvle or continous stroke -- Emergency stop.

SICOTTE - J 3H-6, ...Vertical Boring Machine24" x 72" Table size, (5) Spindles.Equipped with: -- (3) 1 HP Motors mounted on 24" long arms with motor starter and overload relay. -- (5) 1-1/2" Dia. spindle with set screw locking 1/2" cap. -- (2) Spring-loaded holddowns. -- (1) Additional motor started with overload for future installation of a spindle drive motorFeatures: -- 0" - 8" Vertical table feed, hydraulically operated, variable feed, and table travel adjustable from front of machine. -- 3 HP Hydraulic pump motor with reservoir. Complete with: -- Electrical Control System with separate motor controls. -- Single or continuous stroke. -- Manual and automatic cycle. -- Foot pedal actuation. -- (1) Safety guard.

SICOTTE - J 3H-7, ...Vertical Boring Machine24" x 84" Table size. Equipped with: -- (5) 1.5 HP Motors mounted on 24" long arms with motor starter and overload relay. -- (5) 1-1/2" Dia. spindles with spring collet 1/2" capacity. -- (2) Spring loaded holddowns.Features: -- 0" - 8" Vertical table feed, hydraulically operated; variable feed and table travel adjustable from front of machine. -- 3 HP Hydraulic pump motor with reservoir. Complete with: -- Electrical Control System with separate motor controls. -- Single or continuous stroke. -- Manual and automatic cycle. -- Foot pedal actuation. -- (1) Safety guard.

SICOTTE J3H-A-6 Angular Vertical Boring Machine24" x 72" Table size Angular boring machine for chair seat -- (6) Hydraulic self feed spindle having 3 7/8" adjustable stroke and variable speed feed, 1 HP motor, jacob chuck 0 to 1/2" capacity, mounted on 24"long arms with timing belt drive. -- The spindle can be set at coumpônd angle angle with 30 deg front to back and 15 deg right top left. -- (2) Air holddowns. -- 0" - 8" Vertical table feed hydraulically operated that can be used when you drill vetically without angle, , variable feed and table travel adjustable from front of machine, -- 3 HP hydraulic pump motor with reservoir. Complete with: -- Electrical control system with separate motor controls, -- Single or continous stroke, -- Manual and automatic cycle and foot pedal actuation, -- Selector switch to activate each spindle manually . -- This machine is design for chair seat boring or any other application where angular holes are required.

SICOTTE - J-30-4, ...Vertical Boring Machine24" x 48" Fixed table and moving head.Specifications: -- (3) 1-1/2" Spindle with spring collet, 1/2" capacity. -- (3) 2 HP - 1,750 RPM - TEFC Motors, each motor with timing belt drives. -- (2) Spring loaded holddowns. -- Table is fixed while the heads with spindles move hydraulically up & down with an adjustable speed feed (this arrangement can be equipped with an automatic feeding device).Features: -- 0" - 8" Adjustable head stroke. -- Foot pedal activated. -- Vertical stroke and feed speed of the heads with spindles are both adjustable. -- 3 HP Hydraulic variable feed motor, vertical spindle movement; movement can be set to either manual, single stoke, or continuous stroke.

CAM-WOOD BR-2096 Double End Boring MachineFeatures: -- The machine is constructed of two opposed horizontal boring units. -- The boring unit can accommodate multiple spindles or multiple drill heads in case less than 2" spacing is required -- (5) Spindles are standard on each boring unit; with pneumatically / hydraulically controlled in/out stroke. -- Multiple spindle boring blocks (heads) are optional and available. -- The spacing of the spindles can quickly be adjusted horizontally for the required hole pattern -- Heavy cast iron base and table assure long life usage.Specifications: -- (2) Drive motors, 3 HP - 3,400 RPM each -- (10) Spindles, 2" in dia. and with 1/2" chuck capacity -- Horizontal Spindle or Boring Head stroke up to 4" -- Maximum working length 96" -- Minimum working length 16" (could be larger due to bit length) -- Table width (each side): 10" -- (3+3) Pneumatic hold-downNOTE: The Boring Units can be "swiveled", making the machine suitable for boring panels on the right, left and front side, or bevel for boring at desired angles.

CAM-WOOD BR 25 + 1 Horizontal and Vertical DrillFeatures & Specifications: The model BR-25+ 1 has the same features as the BR-25, except it's fitted with an additionaluniversal boring head, making it ideal for drilling holes on K/D furniture. -- The boring head can be swiveled 360 degrees for angular drilling, as desired -- Vercical Single Spindle, 2 HP - 3450 RPM 3-phase motor, adjustable vertically and front to back., spindle node threaded 7/16-14" -- Horizontal spindle 2 HP, 3450 RPM-3 phases motor, adjustable 360 degree, spindle nose threaded 7/16-14" -- 5" Horizontal spindle travel (drilling depth) w/foot pedal control. -- 3-1/2" Vertical table adjustment. -- Pneumatic holddown clamp for up to 3" thickness. -- 12" x 10" Table size.

CAM-WOOD BR 25 Horizontal DrillFeatures & Specifications: -- Single Spindle, 2 HP - 3450 RPM 3-phase motor, adjustable vertically and front to back. -- 5" Horizontal spindle travel (drilling depth) w/foot pedal control. -- 3-1/2" Vertical table adjustment. -- Pneumatic holddown clamp for up to 3" thickness. -- 12" x 10" Table size. -- 1/2" Drill chuck / 3/4" max. bit diameter.

CAM-WOOD BR-50 Universal Boring MachineFeatures & Specifications: -- 3 HP Pneumatic Universal Boring Machine, all adjustments feature an index plate for accurate and convenient reading, workplace clamping. -- Vertical Base travel, 24". Horizontal Base travel 12". -- 0" - 4" Spindle stroke, 7/16" - 14-thread screw shank, 1/2" max. bit capacity. -- Table Size: 15" x 22". -- Complete with: Air operated overhead holddown clamp and foot pedal operated drill cycle. -- Drill Head can be swiveled 360° and Optional Multi-Spindle drill heads available.