MURPHY-RODGERS - MRSE-14-RAL: Baghouse Dust CollectorSpecifications: 14" Inlet dia.; 4,836 CFM; (63) bags with: 520 Sq./ft. filter area; 9.3:1 air-to-cloth ratio; 20 HP fan motor; primary separator built into unit; secondary separation of fine particles by filter bag section; -- Equipped with: -- Rotary Air Lock. -- Fully automatic shaker controls with: Electric shaker as standard; consists of panel box with shaker starter; transformer for 115 V circuitry; solid-state timer for fan deceleration & shaking cycle. -- All necessary relays and internal wiring inside the panel box.

MURPHY-RODGERS - HEC-216-S/10: 33,000 CFM Continuous Duty Automatic Self-Cleaning Pulse Jet Baghouse Dust CollectorEquipped with: -- (216) 5" Dia. x 10' L Cloth filter bags for a total of: 2,827 sq/ff. of filter area. -- (2) 42-1/2" W x 68" H & (2) 40-1/2" x 68" H Top access doors. -- (3) Front & (2) side 27" W x 54" H Filter access doors. -- (2) Square cone bottom hoppers each with: 25" x 25" Discharge openings. -- System utilizes: (2) 4-1/2’ x 6’ x 4’ H Waste containers (NOT included). -- CHICAGO 100 HP - 1,780 RPM Roof Mounted Blower with: 41"; Dia. inlet. -- Motorized dampers for winter & summer modes. -- Winter mode: Directs air back into building, reducing heat loss. -- Summer mode: Directs air outside, cooling building. -- Electrical controls (as pictured). VFD needs to be repaired or replaced.Complete with: -- Spare Filter Bags.NOTE: Installed Used in 2016 with "New" 100 HP motor, new bearings in blower & "New" spring mounts.

7.5 HP TEFC BALDOR Motor, 2,960 CFM at 6" W.G., free-standing interior unit, designed for (6) filter bags mounted over two plastic waste bags or barrels for waste collection. -- 10" Inlet dia.; 128 sq. ft. filter area, 66 cu. ft. storage cap.; quick clamp barrel removal. -- It comes with barrels and bags as shown. -- Overall height is 129"; requires 26" x 108" floor space..Magnetic Starter included

MURPHY-RODGERS MRSE-24 RAL Dust Collector Loaded with features -- General Data: Self-contained baghouse, approx 15,000 CFM with 1,913 sq. ft. of filter area based on 7.8 to one Air-to-Cloth-Ratio. -- Fan/Motor: 40 HP Baldor motor, 22" dia. inlet, primary separator built into the unit, secondary separation of fine particles by filter bags. -- Equipped with: 16" dia. bottom dump outlet controlled by a Rotary Air Lock with approx. 18" dia. discharge outlet. -- Complete with: (2) Electric motor driven automatic bag shakers, angle frame truck height support stand with walkway platform and full height ladder to access top of unit. Fan/motor mounted on top of the collector -- Includes: Magnetic Starter, Control Panel, Silencer, and Explosion doors. -- Approx. dims.84" x 85" x 32' High; 6,100 Lbs

MURPHY-RODGERS MRJ-610-122 Pulse Jet Dust Collector with Rotary Air Lock and Transfer Fan.Specifications: -- 8,500 CFM approx. @ 9 to 1 air to cloth ratio baghouse dust collector with (60) 10-feet long filters; total cloth area of 943 sq. ft. -- Filter Cleaning: Continuous Self-cleaning Using Compressed Air. -- Main Fan: 30 HP top-mounted blower motor. with approx 18" dia. inlet. --System includes: Relay/Transfer fan, steel structure support stand, low height as waste is transferred by fan, safety ladder/platform, top safety railing, and approx. 16" Rotary Air Lock.Actual model is MRJ 610 -122.

MURPHY-RODGERS MRZ 17/16L Interior/Open 6 Bag Dust Collector with Auger and Rotary Air Lock General specs: Approx. 7,600 CFM @ 8" SP. (6) top filter bags @ 24" dia. by 72" long. (6) bottom disposable plastic dust storage bags. -- Fan/Motor: 25 HP BALDOR TEFC motor direct driven fan with electrical starter. 17" diameter inlet, with lifting hooks. The bag collector motor is brand new and has never been powered on or fired up. -- Comes with: Main approx. 17" dia trunk line, shut-off, and Quick clamp removal for filter and plastic bags. -- All steel construction with rugged support legs. Air Deflectors allows operator to adjust the air flow and amount of waste evenly into the 6 waste bags. -- Note: NFPA 664 (Fire Code) states that a max. of 5,000 CFM is limit allowed for indoor enclosure-less dust collectors.

NEDERMAN S-1000 BAG FILTER Dust Collector. The NEDERMAN S-Series Baghouse Dust Collector is quick to install and easy to operate. It's the ideal solution for a smaller shop or single work-cell operation.Specifications: -- With a 10 HP motor and a 5,000 CFM @ 7" WG and 360 Sq/ft of filter media. -- 10 HP - 1,750 RPM TEFC Motor, (24) Beane material filter bags and magnetic starter. -- Features: Easy installation, typically (1) hour; quiet operation, (3) waste discharge points. Inlet opening 16". -- Resonable amount of pipe is included.

NEDERMAN S-750 BAG FILTER Dust Collector. The NEDERMAN S-Series Baghouse Dust Collector is quick to install and easy to operate. With a 7.5 HP motor and a 4,500 CFM @ 6" WG it's the ideal solution for the small shop or single work-cell operation. -- Specifications: 7.5 HP - 1,750 RPM TEFC Motor, (24) Beane material filter bags and magnetic starter. -- Features: 243 Sq/ft of filter media, easy installation, typically (1) hour; quiet operation, (3) waste discharge points. Inlet opening 11". -- Available in 208/230 or 480 V, 60 Cy, 3 Ph. Must specify voltage at the time of orderAvailable options:42 Gallons Drum Discharge - Single Drum (3 REQUIRED)230 Gallon Dump Bin

NEDERMAN S-1000 BAG FILTER Dust Collector. The NEDERMAN S-Series Baghouse Dust Collector is quick to install and easy to operate. It's the ideal solution for a smaller shop or single work-cell operation.Specifications: -- With a 10 HP motor and a 5,000 CFM @ 7" WG and 360 Sq/ft of filter media. -- 10 HP - 1,750 RPM TEFC Motor, (24) Beane material filter bags and magnetic starter. -- Features: Easy installation, typically (1) hour; quiet operation, (3) waste discharge points. Inlet opening 16". Available in 208/230/460 V, 60 Cy, 3 Ph. Must specify Voltage at time of orderAvailable option:- Aluminum Impeller: - 45 Gallon Drum Discharge - Single Drum (3 REQUIRED)- 230 Gallon Dump Bin: Available spare parts:- Filter Bag (24 Filters)- Plastic Bags (Roll of 90 - 8 mil thickness) - 500mm Clamp (bags, barrels, and bin)

NEDERMAN S-500 BAG HOUSE DUST COLLECTOR. -- Open Bag house designed for interior application; 5 HP TEFC material fan motor, 1,750 RPM; free standing 2,000 CFM open frame bag house, 162 sq. ft. of filter area via (16) beane material filter bags; 7.5" W.G. static pressure. -- Bottom discharge into (2) plastic waste collection bag. -- Includes: Side-mounted blower assembly with support legs; (2) quick disconnect clamps for the plastic bags. Starter motor with push buttons. Option:42 Gallons Drum Discharge, Single Drum (2 REQUIRED FOR COMPLETE S-500)

New Hangcha FP25C/CPYD25 ForkliftSpecifications: 4,700 Lbs LP cushion unit, Sideshift, 3 Stage full free lift mast, Cushion Tire 4 Wheel Sit Down, LP Gas, Internal Combustion Engine, Powershift transmissionFeatures: -- Travel Speed (Loaded/Unloaded): Approximately 11/12 mph -- Gradeability (Loaded): Approximately 20% -- Service Brake: Hydraulic -- Parking Brake: Manual/Mechanical -- Seat: Adjustable, Steering: Power SteeringDimensions: Overall Length: Approximately 95 inches (varies with fork length), Overall Width: Approximately 42 inches, Overall Height (Overhead Guard): Approximately 83 inches, Wheelbase: Approximately 58 inches, Ground Clearance: Approximately 3.5 inchesNOTE: This will be the last item loaded out. The above specs are taken from literature and considered accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

NEWMAN - SS-24, ...Wood Shaving Mill -- Motor: 100 HP. -- Feed Opening: Up to 5" thick x 14" wide. -- Cutterhead: 24" Dia. x 14" width. -- Knives: (16) Per row x (7) rows; total: (112) knives. -- Some extra knives included. -- Loaded onto your truck.

NORTHFIELD - #4, ...Table SawSpecifications: -- 16" Dia. saw blade cap.; 7.5 HP - 3,450 RPM motor; 1" dia. arbor; 13/16" dado cap. with: Thin collar; blade tilts: 0° - 45°; 32" rip cap. with T-type fence.

NORTHTECH - NT-SL2000XL, ...Straight Line Rip SawSpecifications: -- 20 HP Direct Drive Straight Line Rip Saw. -- 2" Arbor. -- Distance from column to blade: 18 in. -- Saw blade size: 10" - 14". -- 3-1/8" Cutting capacity. -- Glue Line Saw. -- Feed Motor: 1.5 HP. -- Feed Speed: 20 - 105 FPM.

Northtech NT SLR-16SC Precision 16″ Straight Line Rip Saw FEED SYSTEM --Saw motor: 15HP, 3PH 230/460V -- Feed: 1.5HP variable from 40′ – 120′ FPMPRODUCT DIMENSIONS -- Min. thickness: 3/16″ -- Max depth of cut: 4-1/16″ with 16"; Blade -- Max depth of cut: 3-1/16"; with 14"; BladeSpecifications: -- Direct Drive = Direct Drive -- Feed Hp. = 1.5 Hp. -- Feed System = 4"; Split Chain with True Trac -- Feed Speed = 40-120 FPM -- Assisted Start = Wye Delt"; -- Throat Capacity = 18-1/4"; -- Min. Length = 12"; 2nd Roller to Kickback -- Min. Thickness = 3/16″ -- Max. Thickness = 4-1/16"; W/ 16"; BladeGlue Line Rip = Guaranteed 12′ 4/4 stock @ 50 FPMEquipped with & Features -- Blade Size = 14"; Tungsten Carbide Tipped -- Dust Collection = 1417 Total CFM -- Dust Port Out = 4"; Top 6"; Bottom -- Arbor Diameter = 2″ Arbor -- Idle Rollers = (8) Idle Rollers -- Hold Down Style = 8 Spring Loaded Hold Downs -- Kickback Finger = (59) Lower (32) Top -- Automatic Mechanical Oiler -- Low Oil Warning = Low Oil Shut-off -- Laser = 100mw Laser Light & Mount Bracket

WSM - 2852BH, ...Heavy Duty Hammermill/Shredder. -- 200 HP - 1,165 RPM Motor -- Infeed opening size: 52" L x 28" W -- Infeed with: Feed roll, 1-1/2" teeth with 6" spacing. -- (2) Types of Hammers: One a rounded style with hard-faced tips.Machine is part of a Pallet Recycling Plant and includes: -- Pallet Feeder -- Dual Chain Conveyor. -- Vibratory Feeder. -- Inclined Oscillating Table.

WESTERN PNEUMATICS WP12 Rotary Air LockSpecifications: -- Discharge opening: "10 x 16" -- Gear motor drive: DODGE 5 HPFeatures: -- Flange mount for installation.

WILLIAMS - Hammer Mill: Half-round Type ConfigurationFeatures: -- 220 HP Main Drive Motor with Belt Drive; complete with Guard. -- 26"; x 12"; Input Opening. -- Powered Input Pull Rolls -- 4"; Main Shaft with Swing Hammers, approx. 3/8"; thickness -- Ratchet Lift Access Lid. -- Mounted on Steel Support Structure with Access Platform and Ladder -- Pneumatic Bottom Discharge with built-in Viewing Window in Ducting below the Hammermill (no fan included) -- Electrical Cabinet with Motor Starters -- NOTES: This machine was last utilized to break up virgin dried pulp for further processing. Already been removed from service – ready to load.

WINTERSTEIGER - DSG 150 ECO, ...Thin Cutting Frame SawSide & Center Guides: Fitted as standard on the basic machine to guarantee the broadest possible range of application. Specifications: -- 11 kW (15 HP) Main motor; 0.3 - 1.5 MPM feed speeds; 210 mm saw frame stroke with (450) strokes/Min. -- 30 - 216 mm Cutting height, adjustable as required; max. +/- 0.5 mm difference in block height. -- 60 - 150 mm Cutting width (side guide); (2) 23 - 70 mm cutting width (using center guide); (2) channels max. 72.5 mm using 7.5 mm guide or with (5) channels max 24.5 mm using variable block width; 300 mm min. block length. -- 1.5 mm Cutting accuracy; +/- 0.2 mm Cutting loss (depending on saw length). -- Max. (30) saw blades (excluding scraper saws); (3) 120 mm sawdust extraction tubes. -- "Air Jet" Module: Cleans the lamellas and saw blades during the sawing process by blowing away the sawdust; cools down the saw blades during the sawing process and cleans the shaving space of the saw blades. -- "Air Jet" also increases the saw blades life and improves the lamella's accuracy. Sawdust-free lamellas can then be glued immediately after cutting.Comes with transformer

Section of WIREWAY HUSKY Teardrop Pallet Racking Equipped with: (4) 18,000 Lb. Cap. 8-1/2’ H x 3-1/3’ W Teardrop vertical frames, with 3” W x 1-5/8” Thick Frame beams, Step beams vertically adjustable on 2" Centers. (8) 9’ L x 4-3/8” H x 2-5/8” D Step beams, with 1-3/8” H x 1” D Step.