COSTA - AKF-CT-1350, 2-Head Wide Belt (Veneer) Sander52" Width cap.; drum & segmented platen.Head Configuration:1st Head: Rubber covered contact roll.2nd Head: Electronically controlled segmented platen with (42) segments on 32 mm increments.Specifications: -- 1st Head: Rubber covered contact roll 75 shore, 30 HP motor; features 4-position revolving turret for abrasive grit size setting. -- 2nd Head: Electronically controlled segmented platen with (42) segments, powered by 20 HP motor and variable speed by electronic inverter control; with reverse rotation. -- Abrasive belts: 1,380 mm x 3,250 mm (54" x 128"). -- Air blast abrasive belt cleaning. -- Pneumatic belt tensioning with electronic tracking.Equipped with & Features: -- PLC Processor Control. -- Floating feed table + Quick Set. -- Vacuum assist holddown. -- Variable feed speed belt conveyor, powered by 5.5 HP (4 kW) motor. -- Infeed & outfeed spring-loaded holddown shoes on all heads. -- Powered raise & lower conveyor bed with LED readout. -- In- & outfeed roller table extensions and motor load meters.

EMC R-evo Z 1350 Sanding & Polishing Center for multi-directional Superfinishing - Award-winning system!Superfinishing obtained by combining electronically controlled, segmented sanding pads with the continuous rotation of the entire sanding head assembly (carousel). This revolutionary system is equally effective as regular wide belt sanders with 4 heads!The carousel rotation is servo-controlled, and can also be operated at standstill in any angular position. The revolving sanding head provides a much more consistent overall finish, and better use of the entire abrasive sanding belt.Motorized doors, sliding and foldaway. Useful working width 1,350 mm (53"). Working thickness min./max. 5 - 180 mm (0.2" - 7"); Constant pass line.Part/Panel Reading unit with Electronic Segments: -- RB-75 Panel reading at infeed, (75) segments with electronic feeler pads. -- Electronic commands activated by magnetic switches. -- Panel detection by large diameter rubber wheels. -- Integrated electronic system.Machine Specifications: -- Hyper finishing abrasive belt 4,960 x 1,430 mm (195.3" x 56-5/16"). -- Chevron belt (inside) length 4,560 mm (179.5"). -- Carousel rotating speed infinitely variable 0.1 - 40 RPM. -- Two electronically controlled segmented sanding pads. Both with 75 segments, each 18 mm wide. -- APC - Automatic Programmable Control and setting of the air pressure for the electronic pads. -- Sanding pads pressure controllable from 0 - 4 bar (0 - 58 PSI). -- Main motor 11 kW (15 HP), Inverter Controlled for infinitely variable abrasive belt speeds 3 - 18 m/Sec (10 - 59 FPS). -- Double oscillating blowers for parts & feed belt cleaning. Activated by part size. -- Motorized linear sliding doors, total stroke 2,100 mm (82.7"). -- Including abrasive belt loading trolley for easy exchange of the sanding belt. -- At outfeed: TAMPICO brush roller for part cleaning, diameter 150 mm (6"), and TAMPICO brush roller for feed belt cleaning, diameter 150 mm (6").Feed System: -- Constant pass line, 900 mm (35-7/16") from floor. -- P.A. Automatic thickness caliper with radio frequency remote control. -- Idle table rollers support in infeed and outfeed. -- Rubber covered presser rollers, grooved. -- Vacuum conveyor bed assembly, fan mounted inside the machine. Inverter controlled 4 kW (5,5 HP) motor. -- Variable feed belt speed, adjustable from 2,5 to 16 m/Min (8 - 52 FPM), Inverter Controlled. -- Large diameter screws on machined guides with columns and pistons. -- Automatic feed belt centering device.Machine Management System: -- Electronic programmable color TSD TOUCH SCREEN DISPLAY, 15,4" wide. -- PLC Power Logic Control for high speed data transmitting. CPU Pentium Intel Atom Z510; 1,1 GHz, DDR2 RAM 512MB expandable. -- Connection 3x USB, 1x RS232, 1x Ethernet 10/100/1000. -- Memory capacity of (200) working programs. -- Operating system Microsoft Windows 7. -- Graphic synoptic to facilitate programming. -- Software and connections prepa

EMC ROTOPLUS 1350 – LUC (1)5 + BRILL 15 Polishing & Buffing LineHeavy Duty Automatic Polishing & Buffing line for high gloss lacquered panels, consisting of: -- Infeed Conveyor -- ROTOPLUS 1350 LUC 5+1 - Polishing and Wax Application machine -- Intermediate Conveyor -- ROTOPLUS 1350 BRILL 15x - Buffing Polishing machine -- Outfeed Conveyor -- Synchronization of feed speed of all equipment in the line, the Rotoplus machines including all conveyorsFollowing are the full specifications: -- Infeed Conveyor, 1.500 x 1.350 mm (59" x 53") Constant pass line 900 mm (35") +/- 40 mm (1-9/16"). Variable feed speed inverter controlled and electronically controlled for synchronized speed and transfer with all other machines of the line.Feed speeds from 0,4 to 8 m/Min (1,3 - 26 FPM). -- ROTOPLUS 1350 LUC 5+1Polishing and Wax application machine for high gloss lacquered wood panels for Polyurethane lacquer or brilliant straight, brushes adjustable at different angles. Equipped with (1) longitudinal Brush Head plus (5) rotating brushes on carousel.1st STATION - Longitudinal Polishing Brush:Cleaning polishing cotton brush diameter 275 mm (10-13/16").Length of the brush 1,420 mm (55-5/16").Brush inclined 3° in respect to the parallel 180°.Automatic low pressure Spraying Gun.Longitudinal chain rail system for gun movement.Electric adjustment of the working pressure, operated from main touch screen control unit.Main motor power 7,5 kW (10 HP).Rotating speed adjustable from 260 to 960 RPM by means of inverter 7,5 kW (10 HP). 2nd STATION - Polishing Carousel: CAROUSEL with (5) Brushes.Max. Brush diameter: 350 mm (13-3/4").Spindle diameter 80 mm (3-1/8").Spindle length: 400 mm (15-3/4").(5) Independent motors, 5,5 kW (7,5 HP) each, with counter bearing supports.The working angle of the brushes is adjustable.Variable speed adjustable from 3 to 36 RPM by means of electronic inverter, driven by 4 kW (5,5 HP) motor.Clockwise and anti-clockwise direction of rotation.Programmable speed control operated from main electronic touch screen display. (5) Special shafts for brushes support EXTRA in addition to the standard ones.(5) Cotton rags 350 mm (13-3/4") to fit the shafts.Automatic System for Abrasive Wax application:Pressurized tank (50) liters for liquid abrasives, with automatic miscellaneous bottom exit and pressure regulator for gun.Low pressure spraying gun for liquid abrasives.Electronic valve for spray gun control.Infrared high precision photocell to detect the panels and activate the spraying gun.Adjustable support for spraying gun positioning.Software and graphic control, programmable through PLC and touch screen. Software and Plug for Telemetry. Computer remote diagnostics control: Direct computer connection between EMC and customer, for online support. -- Intermediate Conveyor, 1.500 x 1.350 mm (59" x 53"), Constant pass line 900 mm (35") +/- 40 mm (1-9/16"). Variable feed speed inve

EMC FLEXY 1350 2RP Finishing Sander with (2) Sanding Heads, Roller and Segmented Finishing PadUseful working width 1,350 mm (53"). Working thickness min./max. 3 - 180 mm (1/8" - 7-1/16"). Head configuration:1st Head: Roller "R" Belt dimensions: 2,620 x 1,370 mm (103" x 54"). -- Roller diameter: 250 mm (10"). -- Roller rubber hardness 85 Shore. Constant control to any position with accuracy 0.02 mm. -- Electronic motorized roller pressure adjustment "grit-set system". -- Rotation: Against feed (clockwise). -- Motor power: 22 kW (15 HP). Automatic star-delta starter. -- Abrasive belt cutting speed: 18 m/Sec (59 FPS). Oscillating abrasive belt blower for the roller unit.2nd Head: Segmented Finishing Pad "P" Electronic PAD segmented in (50) sections. -- Belt dimensions: 2.620 x 1.370 mm (103" x 54"). -- Width of the segmented element (section): 27.0 mm (1-1/16"). -- Rotation: Against feed (clockwise). -- Timed oscillating abrasive belt blower. -- Motor power: 11 kW (15 HP) with electronic inverter variable abrasive belt speed 3 to 18 m/Sec (9.8 - 59 FPS).Feed system:Constant pass line, 900 mm (35.4") from floor &#9679 Vacuum conveyor bed, 4 kW Vacuum unit for holddown of smaller parts, mounted inside of the machine base. &#9679 Idle table rollers support in infeed and outfeed. &#9679 Rubber covered presser rollers, grooved. &#9679 Variable feed belt speed, adjustable from 3 to 18 m/Min (9.8 - 59 FPM) Inverter Controlled. &#9679 Large diameter screws on machined guides with columns and pistons. &#9679 Automatic feed belt centering device.General Machine Features: -- Independent main motors. -- Analog ammeters, for each motor, on main control cabinet. -- Electronic motorized "grit set" system; control from touch screen for each working group (head).Electronic programmable color TOUCH SCREEN display, 10" wide &#9679 PLC with micro-processor of latest generation, modular and expandable &#9679 Connection USB, RS232, Ethernet 10/100/1000 &#9679 Memory capacity: 100 working programs or more &#9679 Graphic synoptic to facilitate programmingSoftware facilities: -- Automatic motor sequence starting. -- Display report and reset of alarms (self diagnostic) with memory records. -- Command, programming and display for:&#9679 all electronic pad functions&#9679 thickness&#9679 feeding&#9679 all inverters and for selected groups (heads).&#9679 blowers, including compressed air saving function.Centralized Control Cabinet: IP 54 protection against dust & moisture. Analog ammeter on main control cabinet. Table lifting-lowering thickness system electrically controlled. AUTOMATIC Delta - Star starter on abrasive belt motors. Centralized Independent Pneumatic Control Cabinet: IP 54 protection. Pneumatic air filter with automatic water-drain system. Pneumatic adjustment for "Grit set system". Pneumatic plant working without lubrication. Compressed air pressure 6 bar (85 PSI) Options Available: Tampico Brush natural fiber brush for cleaning of

EMC UNDERTOP 1300 2+2 - Wide Belt Sanding Line Top + Bottom, both with (2) Sanding Heads; Steel Roller, Rubber covered Roller.This machine is equipped to process cement fibers!Useful working width 1,300 mm (51"). Working thickness min./max. 3 - 160 mm (1/8" - 6-5/16"). Both Bottom + Top units are equipped as follows:1st Head: Steel Roller "R", Belt dimensions: 1,900 x 1,320 mm (74" x 52"). -- Roller diameter:190 mm (7-1/2"), spirally grooved. -- Constant control to any position with accuracy 0.02 mm. -- "Grit-set system" for sanding belt grit compensation. -- Rotation: Against feed (clockwise). -- Motor power: 22 kW (30 HP) with Automatic star-delta starter. -- Abrasive Belt cutting speed: 21 m/Sec (69 FPS). -- Air Jet Blower for abrasive belt cleaning.2nd Head: Roller "R", Rubber covered, spirally grooved. Belt dimensions: 1,900 x 1,320 mm (74" x 52"). -- Roller diameter:190 mm (7-1/2"). Shore hardness 85. -- Constant control to any position with accuracy 0.02 mm. -- "Grit-set system" for sanding belt grit compensation. -- Rotation: Against feed (clockwise). -- Motor power: 15 kW (20 HP) with Automatic star-delta starter. -- Abrasive Belt cutting speed: 21 m/Sec (69 FPS). -- Air Jet Blower for abrasive belt cleaning. Feed system: -- Constant pass line, 980 mm (38-9/16") from floor. -- Idle table rollers support in infeed and outfeed. -- Rubber covered presser rollers, grooved. -- Variable feed belt speed, adjustable from 3 to 19 m/Min (9.8 - 62 FPM), Inverter Controlled, synchronized feed speed between both machines. -- Motorized height adjustment on (4) precision screws. -- Large diameter screws on machined guides with columns and pistons. -- Automatic feed belt centering device. -- Pre-welded machined working table. -- Pneumatic air floating pressure holddown shoes at infeed, in middle position, and in outfeed position. These pressure holddown shoes are chrome hardened for processing of cement fibers!General Machine Features: -- Independent main motors. -- Analog ammeters, for each motor, on main control cabinet. -- Electronic motorized grit set system, control from touch screen for each (head) working group. Electronic programmable color TOUCH SCREEN LCD display, 7" wide -- Resolution 640 x 480 pixels. -- PLC with micro-processor of latest generation, modular and expandable. -- Memory capacity: (100) working programs or more. -- Graphic synoptic to facilitate programming. Front protection IP 65 against dust & moisture.Software facilities: -- Automatic motor sequence starting. -- Display report and reset of alarms (self diagnostic) with memory records. -- Command, programming and display for: &#9679 all electronic pad functions. &#9679 thickness. &#9679 feeding. &#9679 all speed control inverters. &#9679 selected groups. &#9679 blowers, including compressed air saving function. Options Included: -- Vacuum beds both on top + bottom, 4 kw (5,5 HP) each. Vacuum unit for holddown of smaller parts, mounted inside o

EMC EXPLORER 1100 2RK ... Wide Belt Sander with (2) Sanding Heads; Roller and Combination head roller/pad.Versatile, medium duty machine, ideal for cabinet shops etc.TECHNICAL DATA: -- Useful working width 1,100 mm (43"). -- Working thickness min./max. mm 3 - 170 (1/8" - 6-11/16"). -- Abrasive belt dimension (length) 1,900 mm (75") x (width) 1,120 mm (44"). -- Feed belt speeds adjustable by electronic inverter from 3 to 17 m/Min (10 - 55 FPM). Head configuration:1st Head: Steel Contact Roller -- Roller diameter 142 mm (6") -- Automatic abrasive belt grit compensation with "Grit-Set System". -- On/Off Selector control with pneumatic piston to select roller. -- Motor power 11 kW (15 HP). -- Automatic Star-delta starter. -- Speed rotation: 18 m/Sec (59 FPS).2nd Head: Combination Roller & Pad. -- Roller diameter 142 mm (6"). -- Rubber covered roller with hardness 45 Shore. -- Automatic abrasive belt grit compensation with "Grit-Set System". -- On/Off Selector control with pneumatic piston to select roller. Flexible sanding pad. Quick Change System for removable pad with felt, rubber and graphite. Rotating cutting speed 17 m/Sec (55.8 FPS). --Driven by same main motor.Abrasive belts oscillation by means of electronic photocell sensor.Feed System: -- Working thickness min./max. mm 3 - 190 (1/8" - 7-1/2"). -- Motorized table lifting including fine adjustment, on 4 precision screws. Natural rubber conveyor belt, machined. Automatic feed belt centering device. Electronic digital display for working thickness; resolution 0.1 mm (0.004"). -- Feed belt speeds adjustable by electronic inverter from 3 to 17 m/Min (10 - 55 FPM). Centralized Control Cabinet: -- Control panel with self-diagnostics alarm control unit. -- Analog load meters on main control cabinet. -- Table lifting-lowering thickness system, electrically controlled. -- AUTOMATIC Delta - Star starter on main motor and IP 54 protection against dust & moisture. Centralized Independent Pneumatic Control Cabinet: -- Pneumatic air filter with automatic water-drain system. -- Pneumatic adjustment for "Grit set system". --Pneumatic plant working without lubrication. Compressed air pressure 6 bar (85 PSI). IP 54 protection against dust & moisture. Safety Features: -- Anti-kickback infeed protection. -- Oversized parts infeed protection by swinging bar. -- Emergency push buttons front & rear. --Automatic brakes on main motor. -- Automatic emergency stop and alarm displayOption: TAMPICO Cleaning Brush, 150 mm (6") diameter. Please add ...$3,400USA UL or Canada CSA Safety Features

EMC MERCURY 1350 2RK ... Wide Belt Sander with (2) Sanding Heads; Roller and Combination head roller/pneumatic pad.Versatile, medium duty machine, ideal for cabinet shops etc.TECHNICAL DATA: -- Useful working width 1,350 mm (53"). -- Working thickness min./max. mm 3 - 170 (1/8" - 6-11/16"). -- Abrasive belt dimension (length) 2,200 mm (86-5/8") x (width) 1,320 mm (52"). -- Feed belt speeds adjustable by electronic inverter from 3 to 19 m/Min (10 - 62 FPM). Head configuration:1st Head: Steel Contact Roller -- Roller diameter 180 mm (7"), spirally grooved. -- Automatic abrasive belt grit compensation with "Grit-Set System". -- Motor power 11 kW (15 HP) driving both heads, with soft starter. -- On/Off Selector control with pneumatic piston to select roller. -- Automatic Star-delta starter. -- Speed rotation: 18 m/Sec (59 FPS).2nd Head: Combination Roller & Pad. -- Roller diameter 140 mm (5-1/2"). -- Rubber covered roller with hardness 45 Shore. -- Automatic abrasive belt grit compensation with "Grit-Set System". -- On/Off Selector control with pneumatic piston to select roller. -- New pneumatic aluminium sanding pad, lamina 40 mm. With On/Off selector. -- Quick Change System for removable pad with felt, rubber and graphite. -- Rotating cutting speed 18 m/Sec (59 FPS). -- Driven by same main motor, with soft starter.Abrasive belts oscillation by means of electronic photocell sensor.Feed System: -- Working thickness min./max. mm 3 - 170 (1/8" - 6-11/16"). -- Motorized table lifting including fine adjustment, on 4 precision screws. Natural rubber conveyor belt, machined. Automatic feed belt centering device. Electronic digital display for working thickness; resolution 0.1 mm (0.004"). -- Feed belt speeds adjustable by electronic inverter from 3 to 19 m/Min (10 - 62 FPM). -- Table rollers. Extension supports with idle rollers in infeed & outfeed.Centralized Control Cabinet: -- Control panel with self-diagnostics alarm control unit. -- Analog load meter on main control cabinet. -- Table lifting-lowering thickness system, electrically controlled. -- AUTOMATIC Delta - Star starter on main motor and IP 54 protection against dust & moisture. Centralized Independent Pneumatic Control Cabinet: -- Pneumatic air filter with automatic water-drain system. -- Pneumatic adjustment for "Grit set system". -- Pneumatic plant working without lubrication. Compressed air pressure 6 bar (85 PSI). IP 54 protection against dust & moisture. Safety Features: -- Anti-kickback infeed protection. -- Oversized parts infeed protection by swinging bar. -- Emergency push buttons front & rear. --Automatic brake on main motor. -- Automatic emergency stop and alarm displayUSA UL or Canada CSA Safety Features

EMC PIONEER 2RK Wide Belt Sander, (2) Head: 37" Width capacity. Drum, Combination Head.Head Configuration: 1st Head: -- Rubber covered contact roll 180 mm diameter.2nd Head: -- Combination Head, rubber covered roller with padSpecifications: -- Useful working width: 950 mm (37"). -- Working thickness min/max: 3 - 170 mm. -- Abrasive belts length: 1,900 mm. -- Abrasive belt width: 975 mm. -- (2) Feed speeds: 5 - 10 m/min. -- Electronic digital display for working thickness. -- Abrasive belt oscillation by electronic photocell. -- Main drive motor 15 HP -- Feed drive 2 to 19 Meter/min.

Plant Boiler System for up to 60,000 pounds of steam production per hour (1790 HP) with the following features and main components: -- (2) ENGLISH BOILER AND TUBE, INC. Boilers each rated for 20,700 pounds of steam per hour each. However, manufacturer specified they can be operated at 30,000 pounds per hour with dry wood or bark fuel (12 percent moisture). -- 250 PSI operating pressure ratings on each Boiler. -- VFD Drives on all main Motors. (The plant uses a maximum 75 HP for each boiler.) -- Electrical Controls. -- (1) Boiler has an Oil Burner for operating optionally on oil if sawdust or wood chips is not available. -- Chemical Water Conditioning System and Pumping System. -- De-aerator and Condensate Tank. -- Multi-clones for particle emissions reduction and abatement. -- (2) Fuel Storage Silos (25’x40’ & 20’x38’) with LAIDIG Model 243 Track-Driven Unloaders. -- Fuel Transfer Conveyors. -- The Silos also are included at the price shown and are available individually. See our listings DB-010162 and DB-010163 for details and individual pricing. -- Boilers can be purchased individually or as a pair. -- Professional removal and installation services are available.

ENTERPRISE - 1616 2-RAM: Horizontal Baler -- 300 HP. -- Overall length: 34'-7" x Width 17'-3". -- Charging chamber: 28" D x 60" W x 110" L. -- Approx. bale size: 31" x 45" x 62".

Industrial Grade EUROVAC I Cyclone Separator & Cartridge Dust Collector Combination. -- Primary Separator: Cyclone on support stand and barrel waste collection: (A Rotary Air Lock with a larger waste bin can be added). Cyclonic action can remove up to 99% of dust and particles. -- SYS-030 Secondary Dust collection: Remaining 1% of dust collected using Cartridge Filter which are automatically cleaned by Pulse Jet cleaning using compressed air housed in a separate compressed air storage tank. -- Vacuum Producer: Heavy Duty cast iron turbine type pump with 10 HP energy efficient squirrel cage motors designed to run continuously all day. built-in thermal heat protection device, and overload protection in Control Panel. High 85" WC vacuum level. -- Control panel house pump starter controls with hand/auto selector for on demand starting. -- Features: Quiet operation with built sound deadening. Diaphragm valves for pulse jet cleaning. -- Approximate dimensions: 180" long x 70" wide x 72" high.

EVASHRED EV60E Dual Shaft Shredder with Infeed ConveyorEvashred is a well-known brand of commercial mobile and stationery shredders for solid waste designed and manufactured by F.V. Evans and Sons also known as Evans Engineering.Every type of shredder is designed specifically to shred a particular type of solid waste including Documents, Car & Truck Tyres, E-scrap (Hard Drives, Computers, Printers known as E-waste and e-scrap), Plastic, Foam rubber, Green Waste, Building Waste even Hospital WasteSpecifications: --30 kW / 40 HP Maximum Power --28-30 RPM Cutter Speed Rotation --Width 640 mm x 37 5mm Cutting Chamber Opening

Used for the accurate radius measuring of cutterheads; allows for speedy tool changes on moulder. 12" Long x 6-1/2" base, 1-1/2" dia. arbor will handle up to 9-1/4" long tool body. -- Digital caliper rides up and down on precision machined octagonal bar. -- Options: T-bushings for 1-13/16" dia. & 40mm dia., please specify.

EXCEL - EX60: (Non-Ferrous) Horizontal Closed Door Baler with Infeed ConveyorSpecifications: -- Motor: 20 HP. -- Cylinder: 9". -- Ram Force: 190,851 Lbs. -- Feed Opening: 40" x 55". -- Full Bale Chamber Penetration. -- Wear Liners: Hardrock 400. -- Automatic Shear Jam Correction.Price includes "Loading onto your Truck!"

EXCEL - 2R63, ...2-Ram Horizontal BalerSpecifications: -- Main. Cylinders: Twin 6". -- Eject Cylinder: 6" -- Main motor: 20 HP. -- Cycle Time: 29 Sec. -- Overall Force: 159,467 Lbs. -- Feed Opening: 60" x 54". -- Bale Size: 60" x 48" x 30".Equipped with: -- U.S. 343 13 Gauge Wire Tier

EXTREMA XP-615AZ Single Sided Head PlanerSpecifications: -- Width: 24" -- Main HP: 15 HP -- Feed HP: 1 HP -- Elevation HP: 0.5 HP -- Max. Thickness: 8.75" -- Min. Thickness: 0.375" -- Max. Cut: 0.25" -- Min. Length: 10.5" -- Cutterhead Speed: 6000 RPM -- Feed Speed: 20-42 ft/min -- Air Requirements: 1000 CFM -- Thickness Adjustment: PLC ControllerBed Roller Adjustment: External -- Powered Bed Rollers: Top and Bottom -- lnfeed Roller: Standard -- Amps (230V / 460V): 41A/20A -- Weight: 2345 LbsFeatures: -- Solid cast-iron construction -- Sectional infeed rollers -- Huge 8-3/4"thickness capacity -- 6000 RPM cutterheads -- Anti-kickback fingers -- Segmented chip breakers -- Sectional feed rollers -- XP-615 Digital Controller -- Motorized table elevation -- Available with straight, STEALTH, or ilECTDFi cutterheads -- Heavy duty screwjack elevation system -- Easy access internal workings -- External bed roller adjustmentsOptional: -- In-feed Roller

EXTREMA - DCY-1220 L3 TYPHOON: Cyclone Filtration Dust Collection System. -- Powerful 2-stage dust collection drops out heavier dust particles through a Rotary Air Lock, allowing you to choose the disposal system before passing finer particles through the fan and filter. -- Air volume rated @ 8,800 CFM. -- Unit includes: 20 HP Motor with a Soft Start already wired in. -- Rotary air lock with: 1 HP Motor @ 38 CFM. -- Low noise operation. -- Standard support frame: LEG 3; 164" clear height x 149" clear width x 91" clear depth. Includes after filter Baghouse DC-327E. Features: 16" Inlet; (3) sections with (9) socks per section. -- Filter Socks: 6" Dia. x 70-7/8" for greater air-to-filter ratio; (1) micron filter. -- Unit is enclosed.

EXTREMA PERFORMA XS-2P52 Wide Belt Sander (2) Heads;52" Width cap. Drum, Roller and Platen - 75"; Belt Lengths Head Configuration: -- 1st Head: Contact drum 30 HP motor; -- 2nd Head: Roller and Platen 30 HP motor.Features: -- Over thickness safety device -- Infeed bed rollers -- Digital thickness controller -- Individual amp meters -- Disc brakes on sanding heads -- Telemecanique electrics. -- Camozzi pneumatics -- Variable speed drive system.Specification: -- Feed motor 3 HP -- Elevation motor 0.5 HP -- Max. thickness 6" - Min. thickness 1/8" -- Contact drum 1st head 8" dia. -- Roller drum on 2nd head 5" dia. -- Dust Collection requirements 4800 CFM -- Feed speeds 15 - 50 FPM. -- Weight 6500 Lbs -- AMPS (220 V / 460 V ) 148/74.

EXTREMA ESO-108.1 Oscillating Edge Sander with End Sanding Kit. -- 6" Wide x 108" long belt, with 1/4" oscillation travel -- 6" x 40" Graphite covered platen. -- 1-1/2 HP Single-Phase motor w/magnetic switch. -- 7" Diameter drive pulley, and 3" Idler pulley. -- 8" x 37" Front table with 5-3/4" vertical adjustment. -- Adjustable 12" x 19" End table for radius work with a 5-3/4" vertical adjustment. -- Heavy laminated tables, fabricated steel base and dust hood with 4" dust collection port. -- CFM Requirements: 400. -- Weight: 425 Lbs.

EXTREMA ESO-108.3 Oscillating Edge Sander with End Sanding Kit. -- 6" Wide x 108" long belt, with 1/4" oscillation travel. -- 6" x 40" Graphite covered platen. -- 2 HP Three-Phase motor w/magnetic switch. -- 7" Diameter drive pulley, and 3" Idler pulley. -- 8" x 37" Front table with 5-3/4" vertical adjustment. -- Adjustable 12" x 19" End table for radius work with a 5-3/4" vertical adjustment. -- Heavy laminated tables, fabricated steel base and dust hood with 4" dust collection port.