KREG KFT 4X8 Face Frame Assembly. -- American-Made 4' x 8' Frame Assembly Clamp with floor stand. -- Working surface at approximately 30° angle for convenience. -- Unit includes; (4) Overhead air cylinders mounted on an overhead beam adjustable up-and-down. -- Clamping beam that moves from left-to-right by means of rollers. -- Squaring bars (fences) on the bottom and both ends of the table. -- Clamping beam with an air filter/oiler/regulator and air outlet at lower end of the beam. -- Optional pneumatic screw gun & pneumatic flex hose.

KREG DK 3100 Electric 3-spindle Pocket DrillSpecifications: -- 1.5 HP Direct drive electric motor; 39-1/2" table/ top working height; (0.5 - 1) Sec cycle time. -- Drills (2) pocket holes in (1) machining cycle across rails of varying widths with 3/8" dia. step bit in (1) smooth operation. -- Drill spindles in the machine are fixed at 3/4" - 1" and 1-3/4" on center allowing it to handle most common rail widths of 1-1/2" up to 3-3/4" with ease. -- One of the (3) Spindles is with left-handed, simply remove one bit from the spindle not being used to set the desired 2-hole spacing. -- The bits are supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material.Features: -- 15ø Boring angle for greater stability, reduced screw breakout & splitting. This produces a smaller "flat-bottom" pocket hole with rounded sides that can be plugged with a dowel if desired.Includes: -- Pressure gauge, fence, hold down, and foot pedal control.

KREG DK 5100 5-Spindle Pneumatic Pocket Hole Machine. -- Individually actuated motors, (5) 0.75 HP motors, mounted on 6" centers. -- Hardened steel drill guides to support drill bit through the operation; 1-touch, foot pedal cycle. -- Swings stops for optimized material positioning; dust collection chutes for efficient chip removal. -- Complete with pre-filter and automatic lubricator.

Single belt oscillating "Tiltable Bed" 0° - 90° sander, 3 HP main motor, 3,400 RPM, belt size 6" x 89", 30.5" long platen. -- Max sanding length 30.5", 4" vertical adjustment of front table, 36" table height, oscillating rate of 121 times/min. -- Includes: (4) interchangable spindles, sizes are 1.25" - 1.5" - 2" & 2.5" dia.

KUFO SK-12RS Straight Line Rip Saw w/Return Conveyor;Entry level Straight-Line Rip Saw with a guaranteed 6' glue line. -- Powered by a 15 HP direct drive motor. -- 12" Dia. Blade capacity for up to 3-1/4" max. cutting height, 4,200 RPM blade speed. -- Equipped with (6) holddowns and a Wye-Delta soft start for lower amp requirements during start-up. -- 1 HP Feed motor, 36 - 145 FPM feed speed, 6" chain width and automatic chain lubrication. -- Treated chain links, pins and raceways withstand heavy use because of an automatic oiler. -- Large 15-3/4" rip capacity. -- Overarm control box mounted on the in-feed side. -- Total space requirements are about the same as a standard size tablesaw. -- Complete with side mounted return conveyor.

Oscillating Edge Sander with end sanding kit. -- 6" Wide x 89" long abrasive belt. -- Tilting 6" x 24" platen. -- 3 HP, single or 3-Phase motor w/emergency switch. -- 6" Diameter drive pulley. -- 8" x 24" Front table with a 4" vertical adjustment and miter gauge. -- End table for radius work. -- Heavy tables, fabricated steel base and dust hood. -- 3-Phase unit model # is SK-3000SDN3.

KUFO LS-1000E Self-contained Dust CollectorDesigned for use in industrial environments for extracting different kinds of dust and dry shavings from single or multiple dust sources. It can be installed directly without any additional fire or explosion protection measures.Specifications: -- 10 HP Direct drive blower with backwardly curved blades and 5,239 CFM air flow rating; Inlet dia. 12". -- 5 Micron Top Filters -- Blower is located on the clean air side. -- Top sound reduction cover at 83 db from original 90 db. -- Fire control system with built-in Fire Sprinkler featuring auto-temperature activation (requires a water line hook-up). -- Pulse jet filter cleaning with compressed air. -- (2) Dust collection tank containers.Options: -- Built in Fire Extinguisher (2) with auto temperature activation. -- "Y" Adapter with 9-3/4" inlet opening with 4" x (5) fitting.

KUFO LS-500E Self-contained Dust CollectorDesigned for use in industrial environments for extracting different kinds of dust and dry shavings from single or multiple dust sources. It can be installed directly without any additional fire or explosion protection measures.Features: -- 5 HP Direct drive blower with backwardly curved blades and 2,649 CFM air flow rating; Inlet dia. 10". -- The blower is located on the clean air side. -- Noise reduction cover to reduce from 82 dB. to 76 dB. -- Fire control system with built-in Fire Sprinkler featuring auto-temperature activation (requires a water line hook-up). -- Pulse-jet filter cleaning with compressed air. -- (1) Dust collection tank container.Options: -- Built-in Fire Extinguisher with auto temperature activation -- "Y" Adapter with 9-3/4" inlet opening with 4" x (5) fitting -- Noise Reduction option (76 dB from 82 dB without).

KUFO UFO-104D Dust Collector4-Bag self-contained free-standing unit (4 up & 4 down, all cloth), 23-3/4" dia. bags. -- Features: 4,167 CFM, 10 HP Motor. -- Bottom mounted 6-manifold inlet branch with (6) 4" inlets connect to a 9.5" dia. inlet; available as option: manifold with (5) 5" dia. inlets. -- Complete with: (4) Upper filter bags 2.5 micron and (4) lower cloth collector bags 2.5 micron, lower collector bags have 21 cu. ft. storage cap. each (84 cu. ft. total) -- Equipped with: Push button starter, base is mounted on (4) swivel casters.

MAX-PAK - HOE-2850-308AR, ...Horizontal Open-End Auto-Tie BalerSpecifications: -- Bale size: 30″ x 42″ x 72″ (variable) -- Bale weight: Up to 1,400 Lbs -- Cycle time: 15.23 Seconds -- Motor: 30 HP -- Cylinder bore: 8″ -- Rod: 5-1/2″ -- Stroke: 70" -- System pressure: 3,000 PSI -- Platen force: 143,256 Lbs - 120.49 PSIFeatures: -- Automatic Wire Tie System -- Heavy wall tubular steel frame -- AR 400 floor and platen -- Hydraulic regenerative circuit and air/oil cooler -- NEMA 12 Electrical panel and Control System -- Conforms to: OSHA &ANSI Z245.5 Standards

MAXPAK HCE60-FE-8 HORIZONTAL CLOSED DOOR BALER -- 8" Main Cylinder -- 30 HP Motor -- Full Eject -- Includes Infeed

MAX-PAK - MP6020-7: Vertical Baler -- Motor: 15 HP. -- Variety of Bale materials: Cardboard; shredded newspaper; aluminum cans; P.E.T. plastics. -- Bale size: 30″ x 48″ x 60″. -- Max. Bale weight: 1,300 Lbs shredded ONP; 1,200 Lbs for OCC.

MAXIFLOW by AQC 9MCH4-72 CARTRIDGE Filter Dust Collector. -- Specifications: 35,000 1CFM range approx (depending on application and ACR required). Filter Cartridge System complete with (72) cylindrical cartridges (130 sq. ft. cloth area per cylindrical cartridge - 13.84"OD x 9.47" ID x 26" long.) for a total 9,360 sq..ft. of filter area. -- Cartridge Specs: SB-820, 100% Polyester Spun-bolded, 8.0 oz/sq. yds. Air permeability 20 -30 CFM/sq. ft. @ 0.5" WG. 200°F continuous operating temperature. -- Comes with: Automatic continuous pulse jet cleaning via compressed air, (1) pulse valve per (2) cartridges; Sequencing Timer in an enclosure. -- Construction: 11 gage fully welded construction. 1/4" thick plate Tube Sheet. (3) V-shape 66" hoppers under filter housing. Heavy Duty steel legs to position unit approximately 43"' above the ground, providing sufficient clearance for (5) 55 Gal. drums.. Housing rated for +/- 20 " WG. Includes 92) 20" dia. top inlet pipe. -- Equipped with: BAE-SW Size 402TWIN CITY Class 4 Air-Foil Fan belt driven by a 150 HP , 1783 RPM, TEFC Fan generates approx 35,000 CFM . Ground-mounted fan/motor. -- Includes: Control Panel. Sprinkler System. Catwalk/Ladder. Barrels & Ducting. -- Services Required: 110V 50-60 Hz; air supply of approx. 22 CFM @ 90 - 100 PSI. Pulses every 10 sec. -- Overall filter approx. dimensions/Weight: 186 W x 111" Deep x 160" H. 9,500 Lbs. -- Seismic rating zone 4, Wind resistance 160 KPH (100 MPH)

ME.SA M21 BORING MACHINE21-Spindle boring head on 32 mm centers, drills vertically from bottom up and head rotates to horizontal position for edge boring, head rotation is manual tilting with assistance from a strut. -- 2-3/4" Max. drilling depth, 2 HP - 2,800 RPM motor, pneumatic drill head advance with speed control; head height adjustment with mechanical digital readout; 34" x 20" table size, max. workpiece width 31-1/2". -- Equipped with: Left & right side fences with stops for mirror-image fence setting for right- & left-hand boring, (2) pneumatic holddown clamps, pneumatic foot pedal control, and magnetic starter with overload protection.

ME.SA M21 BORING MACHINE21-Spindle boring head on 32 mm centers, drills vertically from bottom up and head rotates to horizontal position for edge boring, head rotation is manual tilting with assistance from a strut. -- 2-3/4" Max. drilling depth, 2 HP - 2,800 RPM motor, pneumatic drill head advance with speed control; head height adjustment with mechanical digital readout; 34" x 20" table size, max. workpiece width 31-1/2". -- Equipped with: Left & right side fences with stops for mirror-image fence setting for right- & left-hand boring, (2) pneumatic holddown clamps, pneumatic foot pedal control, and magnetic starter with overload protection.

Mereen-Johnson 424 DCS Short Stock Gang Rip sawSpecifications -- 24" Arbor cap., -- 14" max. dia. tooling, -- 3-1/2" max. manual thickness adjustment, -- 14" min. length for glue joint accuracy and 22" min. for busting only, -- 6" throat. Equipped with and Features -- 75 HP - 3,600 RPM TEFC Direct drive motor, -- 2-3/16" dia. arbor with disc brake, -- load meter and slip-off outboard bearing. -- Feed & chain: 3 HP Variable feed speed 30 to 170 FPM, -- M-J "Posi-Feed" dip bed carried on 5" pitch hardened double-V chain -- "Quad Life" hardened dip cams -- Extruded structural aluminum feed bed slats with replaceable steel backed rubber insert strips --, Automatic chain oiler. -- (4) 3" Dia. air loaded overhead pressure rolls; full width spring loaded overhead bed plate, -- Pressure rolls and bed plate unit with scale & pointer thickness reference; -- Anti-kickback finger system with (1) lower & (2) upper on infeed. -- Sound enclosure, -- (2) Upper dust hoods (1) 10" & (1) 5" dia. and (1) lower 4" dia. hood, -- Requires 3,820 CFM;NOTE: Laser Rack with 10 Lasers

Mereen-Johnson 424 Gang Rip sawSpecifications -- 24" Arbor cap., -- 14" max. dia. tooling, -- 3-1/2" max. manual thickness adjustment, -- 14" min. length for glue joint accuracy and 22" min. for busting only, -- 6" throat. Equipped with and Features -- 75 HP - 3,600 RPM TEFC Direct drive motor, -- 2-3/16" dia. arbor with disc brake, -- load meter and slip-off outboard bearing. -- Feed & chain: 3 HP Variable feed speed 30 to 170 FPM, -- M-J "Posi-Feed" dip bed carried on 5" pitch hardened double-V chain -- "Quad Life" hardened dip cams -- Extruded structural aluminum feed bed slats with replaceable steel backed rubber insert strips --, Automatic chain oiler. -- (4) 3" Dia. air loaded overhead pressure rolls; full width spring loaded overhead bed plate, -- Pressure rolls and bed plate unit with scale & pointer thickness reference; -- Anti-kickback finger system with (1) lower & (2) upper on infeed. -- Sound enclosure, -- (2) Upper dust hoods (1) 10" & (1) 5" dia. and (1) lower 4" dia. hood, -- Requires 3,820 CFM;Also included: -- (7) laser with mounting rack -- (2) additional arbor and lots of spacers

MEREEN-JOHNSON - 431DC, ...Gang Rip Saw: Specifications: -- 31" Arbor width cap., 14" max. dia. tooling, 3-1/2" max thickness. -- Motorized thickness adjustment. -- 29" Min. length for glue joint accuracy and 22" min. for busting only; 6" throat. -- 75 HP - 3,600 RPM TEFC direct drive motor. -- Arbor with disc brake & load meter. -- Arbor lockout on the access door.Equipped with & Features: -- Feed, Chain & Holddown. -- 5 HP Variable feed speed 30 - 150 FPM with adjustable jam protection. -- MEREEN-JOHNSON "Posi-Feed" dip bed carried on 5" pitch hardened double-V chain. --"Quad Life" hardened dip cams. -- Extruded structural aluminum feed bed slats with replaceable steel backed rubber insert strips. -- Automatic chain oiler with low-level shutoff. -- (4) 3" Dia. air loaded overhead pressure rolls. -- Full width spring loaded overhead bed plate. -- Pressure rolls & bed plate unit with powered adjustment; scale & pointer for thickness reference; -- Antikickback Finger System with: (1) Lower & (2) Upper on Infeed; (1) upper assembly on outfeed.

MEREEN-JOHNSON - 431DC, ...Gang Rip Saw: Specifications: -- 31" Arbor width cap., 14" max. dia. tooling, 3-1/2" max thickness. -- Motorized thickness adjustment. -- 29" Min. length for glue joint accuracy and 22" min. for busting only; 6" throat. -- 75 HP - 3,600 RPM TEFC direct drive motor. -- Arbor with disc brake & load meter. -- Arbor lockout on the access door.Equipped with & Features: -- Feed, Chain & Holddown. -- 5 HP Variable feed speed 30 - 150 FPM with adjustable jam protection. -- MEREEN-JOHNSON "Posi-Feed" dip bed carried on 5" pitch hardened double-V chain. --"Quad Life" hardened dip cams. -- Extruded structural aluminum feed bed slats with replaceable steel backed rubber insert strips. -- Automatic chain oiler with low-level shutoff. -- (4) 3" Dia. air loaded overhead pressure rolls. -- Full width spring loaded overhead bed plate. -- Pressure rolls & bed plate unit with powered adjustment; scale & pointer for thickness reference; -- Antikickback Finger System with: (1) Lower & (2) Upper on Infeed; (1) upper assembly on outfeed.

Mereen-Johnson 312-DC/SR2 Gang Rip Saw with Rip Navigator Scout InfeedSpecifications -- Arbor Space: 12" -- Thickness Capacity: Up to 3" (w/ 14" Blades) -- Minimum Length: 22" (30" for Glue-Joint) -- Two Shifting Blades -- 1"Minimum Net Rip Between Shifting Blades -- Machine-Mounted Laser Stand -- Arbor Motor: 50 HP, Direct-Drive -- Feed Motor: 3 HP -- Variable Speed Feed: 30 - 150 FPM -- "Posi-Feed" Friction Feed Chain w/ Aluminum Slats and Replaceable Rubber Inserts (Rubber Inserts are Brand New) -- Hardened Steel Feed Chains & Track w/ Oil Mist Lubrication -- Air-Loaded Press Rolls -- Single Lower, Double Upper Infeed Anti-Kickback Fingers w/ Single Upper OutfeedEquipped with & Features -- Rip Navigator Scout Arranged to Receive 17'-6" Maximum Length Boards from Scissors Lift Manually placed on Board Dealer ArmsIndividual Boards are Automatically Dealt onto Lateral Chains and Conveyed to a Board Stop -- Board Stop Queues Boards for Advancement to Disappearing Fence -- Automatic Adjusting Fence Positions Boards for Placement into Gang Rip Saw Fence Positioning Through Rip Navigator -- Fence Mounted Pinch Roll Feeds -- Board to Gang Rip Saw Mounted Power Table -- Voltage: 480 with Transformer (Original Voltage as built is 575) -- New Bearing in Saw Arbor -- New Rails for Scout Infeed Chains -- 5743 HOURS -- NEW IN 2013