TASK MASTER TM-8512 DOUBLE SHAFT SHREDDERSpecifications & Features: -- TASKMASTER® TM8500 is a small grinder that delivers powerful capabilities. -- With its twin shaft design, this unit can perform in applications like no other by providing excellent feeding characteristics on a variety of solids. -- These units feature an 8.5"; wide cutting chamber with various chamber lengths. -- These versatile shredders can handle screenings, fish waste, fabrics, waste material, sludge, food waste, plant material, and much more.Features: -- 5 HP Motor -- Coarse or Finely Cut Output Configurations -- CUTTER CARTRIDGE® Technology -- Few Moving Parts -- No Stack Retightening -- Rugged Construction

TAYLOR - 20-Section: Clamp Carrier Specifications -- 8-1/2' Width cap. -- 39" Max. clamp opening; 2-1/2" Jaw height. -- Approx. (4) clamps per section.Equipped with: -- (75) Clamps total. -- Pneumatic tightener. -- Pneumatic panel flattener.Complete with: -- Air drive carrier rotation. -- I-Beam chain assembly.NOTE: Already taken down.

TAYLOR 40 Section Clamp Carrier.Specifications: -- 40-Section, 8-1/2' width capacity -- Average 4/5 clamps per section (175 clamps total), all with 32" max. clamp opening. -- Equipped with (175) clamps plus a pallet of spares that require repair, 32" clamps with 2-1/2" high jaws .Complete with: -- Heavy Duty Drive for rotation,& clamp tightening. -- Foot pedal control. -- Includes a glue applicator.

Taylor 16 Section Clamp Carrier • 20.5' width cap., (7) clamps per section (128 clamps total).• .48" max. clamp opening clamps with 4-1/2" X 3 1/4" jaw height -- (128) Rocker plate 4" X 6" @ 80-1706 (purchase in June 2024)Complete with: -- Semi automatig clamp ttightening, -- (2) air drive carrier rotation. -- (2) Pneumatic panel flattener -- OAL apprx 24' X 14' X 12'Note: The buyer will be responsible for tear down and loadingMachine model CC 20,5-16-481

--In Auction: https://exfactoryauctions.com/Detail/CR-230068/event/A122024$1 --No Reserve!-- TAYLOR 800036 7' W 12-Section Semi-Automatic Pneumatic Clamp Carrier, with Flattener & Tightener Equipped with: (71) 32” Cap. Clamps, with 4-5/8” W x 3-1/2” H Jaws. Air motor drive. Dual foot pedal control. Complete with: Pneumatic Panel Flattener. Pneumatic Clamp Tightener.

TERCO NORTHSTAR 10-8 Spindle Carver.8-Spindle Carver with 10" center-to-center chuck spacing. -- (2) 0.5 HP - 3,450 RPM spindle motor direct "belt drives" spindles for 11,000 RPM rotation. -- 36" Long carving cap, with optional length extensions up to 72". -- Manual rotation for round parts. -- Operator manually traces the pattern details of the master with copying stylus. -- Capable of doing both base relief (flat backed) and 360° full round carving. -- Includes: (1) Set roughing bits, (2) sets finishing bits, tools, and manual.

THERMWOOD CS 40 CNC Router, 4 X 8 with ATC:Under power for inspection!4' x 8' Moving table machine in a front-to-back configuration with single-zone vacuum plenum. -- Equipped with:(1) 10 HP HSD, ISO-30 type routing spindle, variable spindle speed from 3,000 - 18,000 RPM, 5-position "typewriter-style" ATC mounted on the front of the spindle, and (4) position wine rack at rear of table. -- Features:High-performance closed loop SEIMENS AC Servo motors driving precision ball screws on all axes with TURBO motion for feed speeds up to 2,400 IPM on the X- & Y-axis and 600 IPM on the Z-axis. -- Control:THERMWOOD "91000" PC Based control with WINDOWS/2000 operating system, 3-axis simultaneous motion, handheld programmer with feed rate & spindle speed override. -- Features:Color monitor, large hard drive, CD ROM drive, 3-1/2" floppy disk drive, keyboard, RS-232 port for PC communications, mounted in an air-conditioned Nema-rated control cabinet, E-CABINET software ready. -- Complete with: 18 HP BECKER vacuum pump, assorted tool holders, and documentation.

TIMESAVERS - 352 HDA, ...Abrasive Planer/Sander2-Head, 51" width cap. Heavy Duty Sander. -- 1st Head: Smooth steel contact roll, 11-1/2" dia., 75 HP motor. -- 2nd Head: Spiral Grooved hard rubber contact roll (11-1/2" dia.) , 75 HP motor; 52" x 103" abrasive belts (6,300 & 4,300 SFPM) with POSI-TRAK electronic tracking. Equipped with: -- Heavy-Duty solid rubber (no vacuum holddown) feed belt for Heavy-Duty operation. -- Motorized part thickness adjustment, 0" - 6" opening. -- 38" - 32" Conveyor height passline with MITUTOYO LED readout, conveyor belt feed. -- 5 HP Variable feed speed from 20 - 60 FPM, smooth rubber conveyor belt. -- Infeed & outfeed spring loaded holddown shoes, infeed emergency stop bar, anti-kickback fingers on infeed. -- Disc brakes on sanding head motors, 18" infeed load area, and motor load meters on sanding heads.

Timesavers 2311-24-6 Pro V.42″ Segmented Platen, Wide Belt Sander42″ Segmented Platen, Specifications: -- 3,273 hours. So it is not a high hour machine. -- 42″ width X 4.75″ (120 mm) thickness capacity. -- Controlled via an easy to use touchscreen. -- Stores up to 240 Programs. --Font drum is a 5″ helically grooved rubber drum that is pneumatically actuated from the control panel. -- The head has variable speeds from 275-1,150 RPM. -- The platen is segmented and there is NEW graphite on the platen.Equipped with & Features -- Both the platen and head have dial indicators for fast, easy, accurate control over adjustments. -- Rear of the machine you will find dust sweeps. -- Up top you will also find a pneumatic air wand for abrasive cleaning. -- Cleaning brush. -- On the front center of the machine you will find an auto calibrating unit. -- The vacuum bed has a 15 hp blower with an almost NEW feed mat. -- The feed mat is driven by a 2 hp motor that is VFD controlled allowing for 12-45 FPM.

TIMESAVERS 137-1 SINGLE HEAD WIDE BELT SANDERSpecifications: -- 36" Width capacity, combination sanding head with 6" dia. spiral grooved rubber contact roll. -- 1-1/2" Wide adjustable height polishing platen on slide out assembly. -- 37" x 60" Abrasive belt size.Equipped with: -- 20 HP Main motor, -- Electric eye abrasive belt tracking, and limit switch monitoring. -- 1 HP feed motor with a fixed speed of 30FPM. -- 0" - 8" manual part thickness opening of conveyor bed. -- Double infeed & outfeed rubber covered holddown rollers. Complete with: -- 18" Infeed conveyor extension, motor load meter, and safety stop bar.

TIMESAVER - 113, ...12" Width Single-Head Wide Belt Sander12" Width cap., single drum.Specifications: -- 12" Width capacity. -- 7.5 HP Main motor. -- 6" Dia. drum. -- 0 - 8" Opening capacity. -- 0.5 HP Feed motor. -- Complete with: Posi-Trac electronic tracking and a 12" conveyor extension.

TIMESAVERS 150-1v Wide Belt Sander;1-Head, 50" width cap.; contact roll head with 40 HP motor; 50" x 103" abrasive belt size, air tracking, 2-1/2" max. thickness cap., adjusted by scale; variable feed speed 40 to 100 FPM; incl. in- & outfeed extension. -- Used to have a checkrail edge sanding attachment for sanding sash (no longer available), but includes (1) extra set of new conveyor belts.

TIMESAVER - TB-440-4, ...2-Head Wide Belt Sander40" Width cap.; Drum and Combination Head.Head Configuration:1st Head - 50 HP; 12" rubber covered contact head.2nd Head - 40 HP; combination platen head.Specifications: -- Sander completely rebuilt (15) years ago. -- Rubber covered abrasive rolls were recovered, grooved and balanced, along with ALL pinch rolls recovered at FLETCHER MACHINE CO., Lexington, NC. -- Electric eyes upgraded to BANNER's send and receive type; includes battery backup system for controls (no crashes when machine has power outage). -- Feed speed gear box driven by AC Drive controlled 10 HP motor. -- Rebuild included: Table removed and platens ground flat; all bearings replaced, including pinch rolls and tracking cylinders; tension cylinders plasma sprayed, reground & new factory seal kits. -- Entire machine was disassembled, sand blasted and DUPONT "Zolatone" primed and painted. -- RAINBOW brand feed conveyor belt replaced in 2014. -- Many more upgrades, too many to list: Please contact for additional information. -- Machine is in good condition, running daily, and has had regular recommended service intervals; includes all factory manuals, blueprint drawings, parts list with numbers supplied, and when machine was new. -- Machine used in solid wood wide belt sanding. -- Includes Cloth aluminum Oxide Belts: 7 - 50 grit; 1 - 60 grit; 8 - 80 grit; 2- 120 grit; 8 -1 80 grit..

TIMESAVERS 237-4IC Four-Head Wide Belt Sander37" Width cap. Drum, Drum, Drum, PlatenHead Configuration:1st Head: Rubber covered contact roll, 9-1/2" dia., 30 HP motor;2nd Head: Rubber covered contact roll, 9-1/2 " dia., 25 HP Motor. 3rd Head: 9-1/2" Grooved Rubber Covered Contact Drum With A 20 HP Motor4th Head: Finishing platen, 2-1/2" wide, 20 HP motorSpecification -- 37" x 75" abrasive belts with Pneumatic tracking. -- Motorized part thickness adjustment, height, 0" - 6" opening. -- Automatic part thickness adjustment, -- Infeed & outfeed spring loaded holddown shoes, -- Variable feed speed from 15 - 45 FPM, 5 HP motor. -- Pneumatic feed beltEquipped with & Features: -- Motor load meters, -- Infeed emergency stop bar, -- Controls mounted on belt loading side, -- Automatic Trabon bearing lubrication system, -- Disc brakes on sanding head motors, -- 30" infeed load area.Note: Some spec's need to be verified

TIMESAVER 237-3 IC Wide Belt Sander: 3-Head, 36" cap. - Drum, Drum, Finishing Platen. -- 1st Head: Rubber covered contact roll, 11-1/2" dia., 50 HP motor; -- 2nd Head: Finishing platen 2-1/2" 30 HP motor. -- 3rd Head: Finishing platen 2-1/2" wide, 30 HP motor. Specifications: -- 37" x 75" Abrasive belts. -- "POSI-TRAK" electronic sanding belt tracking. -- Motorized part thickness adjustment. -- 0" - 6" Opening, automatic part thickness adjustment. -- Infeed & outfeed spring loaded holddown shoes. -- Variable feed speed from 15 - 45 FPM, 5 HP feed motor.Additional Features: -- Motor load meters. -- Infeed emergency stop bar. -- Controls mounted on belt loading side. , -- Disc brakes on sanding head motors. -- 30" Infeed load area.Actual model: TIMESAVERS "237-3IC"

TIMESAVER - 337-2, ...2-Head Wide Belt Sander36" Width cap., Drum & Combination HeadHead Configurations:1st Head: 11-1/2" Dia. spiral grooved rubber contact roll 40 HP motor.2nd Head: Combination Head, Rubber contact Roll & Platen 30 HOSpecifications: -- 37" x 75" Abrasive belts with pneumatic tracking. -- 2 HP Feed drive; Variable feed speed from 20 - 60 FPM. -- Infeed & outfeed spring loaded holddown rolls on both heads. -- Motorized thickness adjustment with indicator, 0" - 6" opening. -- Infeed safety stop bar. - Also has adjustable shoes before and after each head. Equipped with & Features: -- Controls mounted on belt loading side. -- Sanding head motors with air caliper disc brakes --Motor load meters.

TIMESAVER 337-2 Wide Belt Sander, (2) Heads36" Width cap., Drum, Combination HeadHead Configurations:1st Head: 11-1/2" Dia. spiral grooved rubber contact roll 40 HP motor.2nd Head: Combination Head, Drum with Platen 30 HP motor. Specifications -- 37" x 75" Abrasive belts with pneumatic tracking. -- 2 HP feed drive; Variable feed speed from 20 - 60 FPM.Equipped with & Features -- Infeed & outfeed spring loaded holddown rolls on both heads. -- Motorized thickness adjustment with indicator, -- 0" - 6" opening. -- Infeed safety stop -- Adjustable shoes before and after each head. -- Controls mounted on belt loading side, --Sanding head motors with air caliper disc brakes, and motor load meters.

TIMESAVERS 252-4-IC, ... Wide Belt Sander, 4-Head.4-Head, 51" cap. - Great sander for solid wood and veneer panels equipped with (2) Contact rolls and (2) Air platens. Head Configuration1st Head: Rubber covered contact roll, 9-1/2" dia. 60 - 70 Durometer, 40 HP motor.2nd Head: Rubber covered contact roll, 9-1/2" dia. 50-60 Durometer, 30 HP Motor.3rd and 4th Head: Finishing platens, 2-1/2" wide "Veneer Saver" inflateable platens with adjustable timers for leading and trailing edges, 20 HP motor each head.Specifications: -- 38" Constant pass line height of Vacuum conveyor with suction fan and motor bed assembly for veneer and solid wood sanding. -- Adjustable air floating infeed and outfeed hold down shoes. -- 52" x 103" abrasive belts with "POSI-TRAK" electronic tracking.Equipped with & Features: -- Motorized part thickness adjustment with mechanical digital readout. -- Auto part thickness set-up, 0" - 6" opening. -- Hydraulic feed belt operation of 15 - 45 FPM via 7-1/2 HP hydraulic pack. -- 4-Motor load meters, controls mounted on belt loading side. -- Disc brakes on sanding head motors. -- 30" Infeed load area.

TiMESAVERS - 237-KA IC, ...Planer Sander w/2-HEADs 2-Head Planer Sander Combination; 37" width capacity.Head Configuration: -- 1st Head. 7" Dia. Helical "Quiet Cut" planer head with: (6) Spirals of 4-sided carbide inserts with 15° rake angle; head turns @ 3,200 RPM; head adjustment with dial indicator readout; 30 HP motor. -- 2nd Head. Combination Sanding head with: 6" Dia. contact roll (60 - 65 Duro) and 2-1/2" wide finishing platen; 25 HP motor; sanding head with: 37" x 75" abrasive belt with "POSI-TRAK" electronic tracking.Feed System: -- Variable feed speed 15 - 45 FPM; automatic conveyor belt tracking; 3-ply rough top conveyor belt. -- Anti-kickback fingers on infeed; air loaded sectional shoe with dial indicator adjustment; double grooved pinch roll on infeed of knife head. -- Infeed & outfeed pinch rolls on sanding head; air activated caliper disc brakes on all heads. -- Motorized part thickness adjustment of 0" - 6" with digital readout.Complete with: -- Controls mounted on belt loading side; main motor fuse protection on both heads; load meters for each head; "over thick" shutoff system; 24" infeed conveyor extension.

Timesavers 2321-45-01 (2) Head wide Belt Sander51" Width cap, Drum, Combination HeadHead Configuration1st Head: Steel contact roll, 8" dia., 30 HP motor.2nd Head: Combination head with a rubber-covered contact roll 5-1/2" dia. and 2-1/2" wide segmented finishing platen, 25 HP motor, (2) dial indicators for contact roll height adjustment.Specifications: 52" x 103" Abrasive belts, -- "Posi-Trak" electronic tracking & pneumatic tensioning, conveyor belt feed. -- 15 - 45 FPM Variable feed speed with inverter control, -- Automatic conveyor belt tracking; -- Double in-feed & out-feed spring loaded hold-down rolls.Equipped with & Features -- 0" - 5" Max. motorized part thickness opening with automatic part thickness set-up, -- Air-operated disc brakes, -- Motor load meters, -- 14" in-feed conveyor area, -- In-feed emergency stop bar."Owner's manual included