SANI-TECH - SC1040/30, ...Auger Compactor -- Motor: 10 HP. -- Hopper capacity: 4.3 Cubic yards. -- Auger RPM: 10. -- Displacement rate: 270 Cubic Yards/Hour. -- 20-Yard Compactor

SAS SCORPION ENGINE PULLER Model SC40 DescriptionIncrease cash recovery from your recycling operationsSAS Forks Scorpion High Speed Motor Puller – Scrap Yard Engine Puller – Auto Recycling Engine Puller – Excellent for self service yards processing vehicles before crushing.Generate revenue:Process end of life vehicles in less than 60 seconds.Pull scrap engines and transmissions in 30 seconds.30% more revenue by separating metals from bodies.1000% more revenue per lb. on wire harness from engine compartment and dash.80% more visibility with a direct line of site from the operator’s window through the forks.Cycle time less than 15 seconds from park to full extension.Serviceable for long life. Replace blades in 3 hours or less.estimated only.Engineered & built for optimum performance:Engineered tough for continuous prying and durability.Hardened pins and bushings and grease-able pivot points for extended service life.Hydraulic hoses and cylinders are protected to minimize potential damage from sharp objects.Built with high strength blades and carriage skid plates for extended service.Clean up of ground debris is a snap with center plow blade.Speed is paramount in this design. Operator uses grapple from the cab, no torches, no personnel needed to hook up chains to pull or move engines. Safer, quicker and less costly removal of engines and transmissions.

Saturn Model 36x20 Slow-Speed Shredder --36" long x 20" wide chamber opening --1/2" knives. -- KYB MRH-30-SW2 hydraulic system powered by a 50-hp three-phase electric motor. --Comes equipped with stand and controls. -- Excellent for plastic, E-scrap, rubber, small tires, paper, cardboard, light metals.

SAVI HFK-250 Veneer Guillotine; General Specs: -- 102.4" (2,600 mm) Width cap., 4" daylight opening, hydraulically operated knife, 4 HP Leroy-Somer motor powers hydraulic unit with reservoir. -- Originally fitted with motorized parallel fence with 0.5 HP two speed gearmotor drive, push button operated, adjustable from 1" - 50" with magnified tape reader in front of machine. -- Equipped with: 2nd Cut feature with automatic reset, laser guide line light, photoelectric barrier guard for knife & hold-down beam, 2-hand operation of knife cycle. -- Note: Rear fence has been removed or modified. Shaft has chain/sprocket.

SAWSTOP - ICS 73230, ....Table Saw w/Safety "Stop Feature"Specifications: -- 10" Blade cap.; 7-1/2 HP motor; 3-1/8" depth of cut @ 0°; 2-1/4" depth of cut @ 45°; 13/16" max. dado width; 5/8" arbor dia. -- Features: -- Enclosed cabinet; Heavy-Duty belt drive; cast iron trunnions; SAWSTOPS's revolutionary flesh detecting safety mechanism. -- Includes: -- 52" "T-Glide" rip fence system; side support table and laminated top; 4" dust collection port; magnetic contractor motor control; main power switch with removable lock-out key. Actual model is: "ICS 73230"

SAWSTOP - 10", ...Table SawSpecifications: -- 10" Blade cap.; 3 HP motor; 3-1/8" depth of cut @ 0°; 2-1/4" depth of cut @ 45°; 13/16" max. dado width; 5/8" arbor diameter. Features: -- Enclosed cabinet, Heavy-Duty belt drive; cast iron trunnions; SAWSTOPS's revolutionary flesh detecting safety mechanism. -- Includes: -- 50" Rip fence; side support table and laminated top; 4" dust collection port. -- Magnetic contactor motor control; main power switch with removable lock-out key. Actual model #: ICS 31230

SAWSTOP - ICS 53230-52, ...10" Table SawSpecifications: -- 10" Blade cap.; 5 HP motor; 3-1/8" depth of cut @ 0°; 2-1/4" depth of cut @ 45°; 13/16" max. dado width; 5/8" arbor diameter. Features: -- Enclosed cabinet; Heavy-Duty belt drive; cast iron trunnions; SAWSTOPS's revolutionary flesh detecting safety mechanism.Includes: -- 52" T-Glide Rip Fence; sliding crosscut table; side support table; 4" dust collection port. -- Magnetic contactor motor control; main power switch with removable lock-out key.

SAWSTOP ICS 53230-52 10" TABLE SAWSpecifications: -- 10" Blade cap., 5 HP motor, 3-1/8" depth of cut @ 0°, 2-1/4" depth of cut @ 45°, 13/16" max. dado width, 5/8" arbor diameter; blade tilt left. Features: -- Enclosed cabinet, heavy-duty belt drive, cast iron trunnions, and SAWSTOPS's revolutionary flesh detecting safety mechanism.Includes: -- 52" T-Glide Rip Fence, side support table; 4" dust collection port; miter guide. -- Magnetic contactor motor control, main power switch with removable lock-out key.

5 HP motor with 8" or 10" blade cap. -- Features: SawStop Safety System, blade stops and retracts on accidental contact, protection is always on, performs continuous self checks, invisible protection, does not interfere with work, compatible with all standard blades; works on all woods and non-conductive materials. -- Includes bypass switch for cutting metal. European style riving knife to minimize kickback; Low profile blade guard for narrow cuts; Quick-change mount for guard and riving knife ÷Large start/stop paddle for hands-free shut off; Main power switch with removable lock-out key; Magnetic contactor motor control; Blade shroud for improved dust collection; Zero-clearance insert; Extra heavy castings ÷Widely spaced trunnions; Infinitely adjustable trunnion assembly for precision alignment. -- Also includes: Vertical slide blade elevation for increased stability; Long-lasting V-ribbed belts; cast iron handwheels; Two access doors in cabinet; Powder-coated cabinet.

SCHEER Veneer Panel Saw. -- General data: 122" Cutting length, 1-1/2" depth of cut, 3/4" - 42" max. back fence cap. with extension fingers, 5 HP arbor motor; saw carriage travels on hardened & ground ways. -- Equipped with: Manual operated saw carriage with hand crank Full-width rear fence with support, hand wheel operated rear fence with scale & arrow readout for positioning. -- Lockable fence at cutting position, fence line also pivots up to permit end trimming against the left guide fence. - Pneumatically controlled hold-down pressure beam. -- Complete with: Push button control and dust collection chute with channel in table base.

SCHELLING FM-430/410 CNC Front Load Panel SawSpecifications & Features: 169" (4292 mm) Cutting length & 165.3" (4,200 mm) pull back, 3.75" (95 mm) max. saw blade projection; 25 HP (19 kW) 4,100 RPM main & 3.4 HP (2.5 kW) 5,600 RPM scoring motor. -- Equipped with: Variable saw carriage travel speed from 0 - 278.8 FPM (85 MPM), constant return of 278 FPM (85 MPM). -- Electronically controlled overhead program fence with rack & pinion driven on both sides; forward speed from 0 - 278 FPM (85 MPM), return speed of 278.8 FPM (85 MPM); equipped with (8) gripper clamps (open up to 5" (130 mm). -- Features: SCHELLING "COMPOSER" IBM-AT Compatible Computer Control; aftermarket color monitor (displays cutting dimensions and patterns w/moving graphics) , self-diagnostic, data input by keyboard; onboard optimization program. -- Complete with: 2-3/4" to 87" (2,200 mm) Long side/cross-cut aligning zone, (1) aligner in front & (1) behind the cut line. -- (3) Front mounted air float tables for moving panel from rip section to the cross-cut section, (2) movable and (1) fixed; each with their own blower. -- Rear of machine fully enclosed for safety with man-height sheet metal panels & wire screen windows. T

SCHELLING - FXH 430, ...Automatic Front Load Panel SawSpecifications: -- 169" Cutting length, 3" cutting height; 3.7" (95 mm) max. saw blade projection, 20 HP (15 kW) main & 3.5 HP (2.6 kW) scoring motor. -- Variable saw carriage travel speed from 0 - 394 FPM (0 -120 MPM) via brushless AC Servo Drive; constant return of 394 FPM (120 MPM). -- Equipped with: -- Electronically controlled overhead program fence, rack & pinion driven on both sides; forward speed from 0 - 262 FPM (0 - 80 MPM) via brushless AC Servo Drive, return speed of 262 FPM (80 MPM); (8) material gripper clamps (open up to 3.5"/ 90 mm). -- Flat guideways on the feeder and saw carriage that has a "Lifetime Guarantee". Features: -- SIEMENS "Fijitsu" IBM-compatible PC with INTEL Celeron 1.2 GHz processor, 30 GB hard drive, 256 MB RAM, floppy drive, CD ROM drive, modem, network card, (2) USB ports, and open expansion slots (all components non-proprietary). -- SIEMENS "Fijitsu" 17-inch monitor; Windows NT based "MCS" saw control software; data input by keyboard or direct downloading from office PC is possible; optimization of programs at Saw. Complete with: -- 90-1/2" (2,300 mm) Long crosscut fence (front-to-back); (2) automatic side/crosscut aligners for up to 87" (2,209 mm) crosscuts; (1) aligner in front & (1) aligner behind pressure beam; (3) front mounted air floatation tables, 24" x 82" (609 x 2,083 mm); (2) tables in rip section are movable. -- Includes: -- Roller support rails rear of machine; rear of machine fully enclosed for safety with man height wire screen fencing.

SCHELLING FXH 430/410 FRONT LOAD, AUTOMATIC PANEL SAW: -- Specifications:169" (4,300 mm) Cutting length & 167" (4,250 mm) pull back; 3.9" (99 mm) max. saw blade projection, 23 HP (17 kW) main & 3.5 HP ((2.6 kW) scoring motor. -- Saw Carriage: Electronically controlled saw carriage with rack & pinion drive; variable travel speed 1 - 394 FPM (1 - 120 MPM), constant return of 394 FPM (120 MPM). -- Pusher Fence: Electronically controlled overhead pusher fence, rack & pinion driven on both sides; (9) Gripper clamps that open up to 3.5" (90 mm). -- Forward speed 0 - 262 FPM (0 - 80 MPM), return speed 262 (80 MPM) FPM; travel via brushless AC Servo Drive -- Operator & Machine Control:PC Front-end with Schelling "MCS" + Windows "NT" operating system.17" Color display with SVGA resolution (displays cutting dimensions & patterns w/moving graphics); virtually unlimited storage capacity, standard keyboard & mouse.Ethernet card; 128 MB Ram, 56K modem. Integrated graphical self-diagnostic, remote diagnostics by the factory is possible via dedicated phone line; data input by keyboard or possible direct downloading from office PC.SCHELLING "MCS" software displays simulation of patterns before actual cutting; graphical representations of cut-to-size parts in production shows the operator what to do in "real time". -- Complete with:2,300 mm Long crosscut fence (front-to-back), (2) automatic side/crosscut aligners for up to 87" (2,210 mm) crosscuts, (1) in front & (1) behind pressure beam cut line.(3) Front mounted air floatation tables, each table 24" x 83" (609 x 2,108 mm), rear of machine fully enclosed for safety with man-height safety fencing. -- Actual Model is SCHELLING FXH 430/410

SCHELLING FH4-330/310 FRONT LOAD, AUTOMATIC PANEL SAW: -- Specifications: 130" (3,330 mm) Rip Cutting cap. & 130" (3,300 mm) pull back; 4.1" (105 mm) saw blade projection; 3.5" (90 mm) Max book height; 24 HP (18 kW) - 3.800 RPM main motor, 3 HP (2.2 kW) - 5,500 RPM scoring motor. -- Saw Carriage: Variable saw carriage travel speed from 16 - 525 FPM (5 - 160 MPM), constant return of 525 FPM (160 MPM). -- Pusher Fence: Programmable overhead program fence, rack & pinion driven on both sides; forward speed from 0 - 262 FPM (0 - 80 MPM), constant return speed of 262 FPM (80 MPM).Pusher fence with (8) material gripper clamps with double clamping fingers, clamps open to 3.5" (90 mm).Operator & Machine Control:PC Front-end controller with SCHELLING "MCS" Evolution + "HPO" Optimizing System + "Windows XP" operating system.17" Color screen displays cutting dimensions & patterns with "REAL TIME" moving graphics, self-diagnostic, data input by keyboard or direct downloading from office PC. -- Complete with:90.5" (2,300 mm) Long crosscut fence (front-to-back), (2) side/crosscut aligners, (1) in front & (1) back of the cut-line, up to 87" (2,210 mm) cross-cutting cap.Electronic scorer adjustment, from the machine control, (3) Front-mounted air float tables with (1) central fan, 24" x 83" (600 x 2,100 mm) each, of which (2) are movable.Fully enclosed for safety with a man-height wire screen fence with access doors. -- Includes:Original Docs, Manuals, tools & tooling as pictured. -- Actual Model is SCHELLING FH4 330/310

SCHELLING FM-H 330/330 Automatic Panel Saw 129.9" (3,200 mm) Cutting length, 3.3" (85 mm) max. saw blade projection.Specifications & Features: -- 11 kW (15 HP) main & 1.6 kW (2 HP) scoring motor. -- Variable saw carriage travel speed from 0 - 262 FPM (80 MPM), constant return of 262 FPM (80 MPM). -- Electronically controlled overhead program fence with grippers, rack & pinion driven on both sides, forward speed from 0 - 262 FPM (80 MPM), return speed of 262 FPM (80 MPM); (6) Clamps open up to 3.9" (100 mm). -- 1,500 mm Long crosscut fence (front-to-back), (2) side/crosscut aligners for up to 87" crosscuts, (1) in front & (1) behind pressure beam. -- SCHELLING "COMPOSER" operating system; on-board SCHELLING optimizer, color monitor (displays cutting dimensions & patterns w/moving graphics), self-diagnostic, data input by keyboard & mouse or direct downloading from office PC is possible. Complete with: -- (3) Front mounted air float tables for moving panel from rip position to crosscut position; fully enclosed for safety with man-height sheet metal panels & wire screen windows.Specifications subject to verification.

SCHELLING FMH 430 Front Load Panel Saw169.2" (4,300 mm) Cutting length, 161" (4,100 mm) pull-back, 3.3" (85 mm) max. saw blade projection, 25 HP (19 kW) main saw motor & 2.5 HP (2 kW) scoring motor. -- Variable saw carriage travel speed from 0 - 262 FPM (80 MPM), return speed of 262 FPM (80 MPM), LED ammeter to show load of main saw motor during operation. -- Electronically controlled overhead program fence, rack & pinion driven on both sides, forward speed from 0 - 262 FPM (80 MPM), return speed of 262 FPM (80 MPM); (9) material gripper clamps open up to 3.1" (80 mm). -- SCHELLING "COMPOSER" Electronic control with color monitor (displays cutting dimensions and patterns w/moving graphics), self-diagnostic, data input by keyboard or possible direct downloading from office PC. -- 90-1/2" (2,300 mm) Long crosscut fence (front-to-back); (2) side/crosscut aligners for up to 87" (2,210 mm) crosscuts; split pressure beam, (1) in front & (1) behind. -- (3) Front mounted air float tables for moving panel from rip position to cross-cut position, 24" x 78" (610 x 1,981 mm) each, (2) in the crosscut section are movable. -- Rear of machine fully enclosed for safety with man-height sheet metal panels & wire screen windows. -- Main saw blade is 370mm, Scoring blades are 200mm. Actual model is FM 430 MCS-F.This machine came equipped with the following optional upgrades: -- Formatting stops (for cutting panels with plastic laminate hanging over the edge), Real time label printing (industrial printer included), Symmetrical Cutting, Window Cutting, Postform Scorer (edge scoring saw that aligns with the main saw blade to reduce chipping at the exit side of the main blade travel), Large miter gauge that mounts to the saw to facilitate making mitered cuts, & Laser light that shows the cutline for freehand manual cutting.

Schneeberger 9 Sculptor Profile GrinderSwiss Made, Schneeberger Automated High Precision Grinder for Finger Joint, router bits, saw blades, straight and milling Cutters. Specifications -- Grinding Motor: 1,500 - 3,000 RPM. -- Cooling Pump: 2,800 RPM. -- Grinding Wheel Speed: 3,000 - 6,000 RPM. -- Grinding Wheel Diameter: 50 - 200 mm. Grinding Wheel Bore: 30 mm. -- Cross Travel of Grinding Wheel: 200 mm. Vertical Travel of Grinding Wheel: 400 mm. -- Grinding Head: Swivel-able. -- Worktable Travel: 400 mm. -- Coolant Capacity: 25 liters. -- Dimensions: 1,226 mm Lenght x 1,160 mm width x 1,180 mm height; Weight - 320 kG.10" Width cap., 11.5" dia., max. profile depth 5.5", radial clearance angle up to 35ø, lateral clearance angle up to 15øEquipped with & Features; -- 2 HP - 1,500 RPM motor, variable grinding speed 2,000 - 4,000 RPM, three sided full jet cooling. -- All std. grinding equipment for HSS grinding, 1-1/2" spindle arbor, (2) wheel flanges, (1) knife holder, dresser.

--In Auction--Starting bid: $100-- Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

SCHUTTE PULVERIZER COMPANY - Model 40 HZF, ...HammermillComplete with the following major components & features: -- Integrated 18", 4,000 CFM Blower. -- WEBSTER 16 Ft. Horizontal Vibrating Conveyor. -- Motor Controls. -- Main drive motor, 75 HP - 3,540 RPM. -- Hammer width is approximately 1-1/4 in. wide. -- 3-1/4" Shaft. -- 24" Dia. Rotor and a tip speed of 22,600. -- 17-1/2" Rotor width. -- 3/4" Main chamber steel. -- Factory Frame.MANUFACTURER'S STATED KEY FEATURES:&#9679 Heavy-Duty plate construction with replaceable liner plates. &#9679 Heavy-Duty grates available in a variety of sizes. &#9679 Heavy-Duty rotor assembly. &#9679 24" Dia. x 3" thick flywheel. &#9679 Built-in fan conveys material up to 50' vertically and 100' horizontally.&#9679 Reversible anvil. &#9679 2-Way reversible "raked" hammers pull wood in without feed rolls. NOTES: &#9679 The HZF Series Horizontal Trim Scrap Grinder is a high-speed, high production Grinder designed specifically for processing longer lengths of wood scrap such as rippings, edging, and trim blocks.&#9679 Available in (4) standard sizes from 10" to 36" wide.