Machine Equipped as follows: NC 410 PC Based Controller Keyboard with Floppy Drive Automatic Strip Feed Magazine Belt Driven Top Pressure Beam Multi-Coiled Infeed Magazine RT63 Pre-Milling Unit SP20 Glue System w/ Pre-Melt Unit Hot Air Gluing system Automatic Infeed Pressure System T45 Front & Rear End Trimming Units w/Tilt RS10 Top & Bottom Rough Trimming Units RF30 Top & Bottom Fine Trimming Units AR10 4 Motor Corner Rounding Trimming Units RB30 Top & Bottom Profile Scraping Units RC10 Top & Bottom Glue Scraping Units SZ30 Top & Bottom Oscillating Buffing Units PH10 Top & Bottom Edge Heaters Specifications: Min. Panel Thickness:....................10mm? Max. Panel Thickness:....................60mm? Height of Edge-Band Material:…..15-65mm? Min. Banding Thickness:.................0.3mm ? Max. Banding Thickness:........ ...... 20mm? Min. Panel Length:...........................150mm? Min. Panel Width:............................ 100mm? Feed Speeds:.................................10-24m./min? Electrics: ......................................... 460-480V 3 Phase

Biesse Akron 440 Edgebander Premill Top & Bottom Trim Corner Round Edge Scrape Glue Scrape Buffing Unit 12-18 m/min Feed Speed All work units are servo controlled

Manufacturer Specs premill hot glue end trim top/bottom trim corner rounding scraping buffing Computer interface

Biesse Akron 245 Edgebander System is still under power until approx mid-October 2024. Touch PLC will need to be replaced. Everything else is working good on the machine. Owner has had it serviced by Biesse.

Min. Panel Thickness: 0.39? Max Panel Thickness: 2.36? Height of Edge-Band Material: 0.55-2.51? Min. Banding Thickness: 0.01? Max Banding Thickness: 0.39? Min. Panel Length: 5.51? Min. Panel Width: 1.96? 2 Feed Speeds: 39ft/min & 59ft/min Electrical: 230V, 60Hz, 3Phase Equipped With Siemens TD200

Biesse Akron 245 Machine was in good working condition when removed from service. Computer works, but the screen does not.

Pressure Beam Type: Rollers Pre-Milling Station: 2 Motors Glue Station Pressure Rollers: 4 End Trimming Station: Straight & Bevel (2 motors) Rough Milling Station: 2 Motor Fine Milling Station: 2 Motor Corner Rounding Station: 2 Motor Flat Scraping Station: Top & Bottom Profile Scraping Station: Top & Bottom Buffing Station: Top & Bottom Heat: Top & Bottom Panel Height: 10-50 mm Edge-banding Material Height: 13-55 mm Min. Thickness of Edge-Banding Strip in Rolls: 0.4-3 mm Max. Edge Thickness w/Trimming Unit: 8 mm Max. Edge Thickness w/o Trimming: 3 mm Max. Section of Solid Wood: 8 x 55 mm Panel Protrusion from Track: 25 mm Min. Panel Length: 150 mm Min. Panel Width (150mm Length): 85 mm Min. Panel Width (250mm Length): 55 mm Chain Feed Speed: 12 m/min Dimensions: 18' L x 4' W x 5' H Weight: 4,000 lbs Electrical: 230 V 3 Phase

Pressure Beam Type: Rollers Pre-Milling Station: 2 Motors Glue Station Pressure Rollers: 4 End Trimming Station: Straight & Bevel (2 motors) Rough Milling Station: 2 Motor Fine Milling Station: 2 Motor Corner Rounding Station: 2 Motor Flat Scraping Station: Top & Bottom Profile Scraping Station: Top & Bottom Buffing Station: Top & Bottom Heat: Top & Bottom Panel Height: 10-50 mm Edge-banding Material Height: 13-55 mm Min. Thickness of Edge-Banding Strip in Rolls: 0.4-3 mm Max. Edge Thickness w/Trimming Unit: 8 mm Max. Edge Thickness w/o Trimming: 3 mm Max. Section of Solid Wood: 8 x 55 mm Panel Protrusion from Track: 25 mm Min. Panel Length: 150 mm Min. Panel Width (150mm Length): 85 mm Min. Panel Width (250mm Length): 55 mm Chain Feed Speed: 12 m/min Dimensions: 18' L x 4' W x 5' H Weight: 4,000 lbs Electrical: 230 V 3 Phase

Brandt KDN 210 Edgebander

2008 Brandt Edgebander 230Y/133V 3 Phase Currently in Production

Brandt KF 76F Edgebander: Pre-milling, top/bottom trim, buffing, extra glue pot

Brandt KDF 440C Edgebander

Pre-milling Unit End Trim Profile/Flush trimming Unit Corner Rounding Unit Profile scraping Buffing Max feed speed: 10 m/min Maximum panel thickness: 50 mm

Brandt KDF 440 Highflex 1440 Edgebander

Brandt KDF 650 Edgebander

Brandt 1100 Edgebander Seller closed shop about 1 year ago and put this in storage. Claims they were using the machine up until they shut down.

Brandt KDN 770 2C Machine has been removed from service. Owner claims it is ready to run! Specs (to be confirmed): Hot Melt granulate quick heat-up glue system, overhead glue tank for easy maintenance & glue color change. Automatic magazine for strip & coil (large 800 mm dia. coil table to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine. (1) Drive plus (3) idle rolls "pneumatically controlled" pressure sections. End Trimming: 0.33 HP - 12,000 RPM Motors, chamfers 0° - 15°. Flush Trimming: Top & bottom, bevels 0° - 15° with (4) revolver type index pre-sets, (2) 0.5 HP - 12,000 RPM motors, cutter heads with insert knives. Fine/Radius Trimming: Top & bottom, bevels 0° - 15° with (4) revolver type index presets (0.5 HP - 12,000 RPM motors), cutter heads with insert knives for 3 mm PVC radius. 2 motor corner rounding Scraping Unit: Top & bottom for 2 - 6 mm radius, pneumatically controlled blowoff nozzles. Buffing Unit: Top & bottom buffing (0.25 HP - 1,400 RPM motors). Variable feed chain track speed from 8 - 20 MPM (26 - 65 FPM), 2 HP feed drive.

Brandt Ambition 1110 Edgebander

2007 Brandt KDF 680 Single sided Edgebander with Pre Milling and Corner Rounding

2016 Casadei Flexa 47 Edgebander 230 V/3 PH