SANDMAN M74836 Downdraft Sanding TableGreat sanding table for a singular function such as doing cabinet doors, door fronts, etc. This downdraft table has a 6″ overhang on the front side making it good for sanding while sitting. Machine comes standard with casters, utility tray, & Felt-lined Platforms.Specifications: 48 L x 36" W top surface with heights of 32", 34" $ 36". -- Overhangs of 6" front. 0" back and 4" ends. -- (2) DP20252 Filters and (1) PF4029 pre-filter. -- 1 HP Baldor Motor – Standard Single Phase 110V (13 Amps) -- (18) Month warranty on parts.(Single and 3-Ph 220V available)NOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.

SANI-TECH - SC1040/30, ...Auger Compactor -- Motor: 10 HP. -- Hopper capacity: 4.3 Cubic yards. -- Auger RPM: 10. -- Displacement rate: 270 Cubic Yards/Hour. -- 20-Yard Compactor

SAS SCORPION ENGINE PULLER Model SC40 DescriptionIncrease cash recovery from your recycling operationsSAS Forks Scorpion High Speed Motor Puller – Scrap Yard Engine Puller – Auto Recycling Engine Puller – Excellent for self service yards processing vehicles before crushing.Generate revenue:Process end of life vehicles in less than 60 seconds.Pull scrap engines and transmissions in 30 seconds.30% more revenue by separating metals from bodies.1000% more revenue per lb. on wire harness from engine compartment and dash.80% more visibility with a direct line of site from the operator’s window through the forks.Cycle time less than 15 seconds from park to full extension.Serviceable for long life. Replace blades in 3 hours or less.estimated only.Engineered & built for optimum performance:Engineered tough for continuous prying and durability.Hardened pins and bushings and grease-able pivot points for extended service life.Hydraulic hoses and cylinders are protected to minimize potential damage from sharp objects.Built with high strength blades and carriage skid plates for extended service.Clean up of ground debris is a snap with center plow blade.Speed is paramount in this design. Operator uses grapple from the cab, no torches, no personnel needed to hook up chains to pull or move engines. Safer, quicker and less costly removal of engines and transmissions.

Saturn Model 36x20 Slow-Speed Shredder --36" long x 20" wide chamber opening --1/2" knives. -- KYB MRH-30-SW2 hydraulic system powered by a 50-hp three-phase electric motor. --Comes equipped with stand and controls. -- Excellent for plastic, E-scrap, rubber, small tires, paper, cardboard, light metals.

SAWSTOP - ICS 73230, ....Table Saw w/Safety "Stop Feature"Specifications: -- 10" Blade cap.; 7-1/2 HP motor; 3-1/8" depth of cut @ 0°; 2-1/4" depth of cut @ 45°; 13/16" max. dado width; 5/8" arbor dia. -- Features: -- Enclosed cabinet; Heavy-Duty belt drive; cast iron trunnions; SAWSTOPS's revolutionary flesh detecting safety mechanism. -- Includes: -- 52" "T-Glide" rip fence system; side support table and laminated top; 4" dust collection port; magnetic contractor motor control; main power switch with removable lock-out key. Actual model is: "ICS 73230"

5 HP motor with 8" or 10" blade cap. -- Features: SawStop Safety System, blade stops and retracts on accidental contact, protection is always on, performs continuous self checks, invisible protection, does not interfere with work, compatible with all standard blades; works on all woods and non-conductive materials. -- Includes bypass switch for cutting metal. European style riving knife to minimize kickback; Low profile blade guard for narrow cuts; Quick-change mount for guard and riving knife ÷Large start/stop paddle for hands-free shut off; Main power switch with removable lock-out key; Magnetic contactor motor control; Blade shroud for improved dust collection; Zero-clearance insert; Extra heavy castings ÷Widely spaced trunnions; Infinitely adjustable trunnion assembly for precision alignment. -- Also includes: Vertical slide blade elevation for increased stability; Long-lasting V-ribbed belts; cast iron handwheels; Two access doors in cabinet; Powder-coated cabinet.

SCHUTTE 280.100 HAMMERMILL -- Type 13100P -- Rotor 24" dia. x 48" wide -- Housing 3/4" thick -- Shaft speed 3,600 rpm -- Heavy duty, statically and dynamically balanced rotor -- (96) Standard notched heat treated hammers 3/8" thick -- Also included; two screens -- Motor 125 HP -- Applications; Planer shavings, dry wood chips, etc. etc.

SCHUTTE PULVERIZER COMPANY - Model 40 HZF, ...HammermillComplete with the following major components & features: -- Integrated 18", 4,000 CFM Blower. -- Mellott Vibrating Conveyor -- Main drive motor: 75 HP -- Hammer width approx. 1-1/4" wide. -- 3-1/4" Shaft. -- 24" Dia. Rotor and a tip speed of 22,600. -- 17-1/2" Rotor width. -- 3/4" Main chamber steel.MANUFACTURER'S STATED KEY FEATURES:&#9679 Heavy-Duty plate construction with replaceable liner plates. &#9679 Heavy-Duty grates available in a variety of sizes. &#9679 Heavy-Duty rotor assembly. &#9679 24" dia. x 3" thick flywheel. &#9679 Built-in fan conveys material up to 50' vertically and 100' horizontally.&#9679 Reversible anvil. &#9679 2-Way reversible "raked" hammers pull wood in without feed rolls. NOTES: &#9679 The" HZF Series" Horizontal Trim Scrap Grinder is a high-speed, high production Grinder designed specifically for processing longer lengths of wood scrap such as: Rippings, edging, and trim blocks. Available in (4) standard sizes from 10" to 36" wide.&#9679 Each model features a built-in fan driven off of the main mill shaft, saving energy and valuable floor space while also significantly increasing production.

SCHUTTE-BUFFALO 15 Series, Model 15300 Wood Grinder;Complete with the following components and features: --Carbon Steel Construction. --Rotor approximate 44" diameter x 72" wide. --Approximately 3" wide Swinging Hammers, tip speed 20,700. --Top feed, bottom discharge. --Bottom screen approximate 5040 square inch area. --Clam shell housing. --500 HP, TEFC, 3/60/460 volt, 1785 RPM drive Motor with coupling and shaft guard. --Mounted on a heavy-duty steel Factory Frame. --NOTES: Largest model of the 15 Series. &#9679 Machine weight 16,000 Lbs.

SCHUTTE BUFFALO - Model WA16L, ... HammermillModel# WA16L, 3500 RPM, with filtration system and multiple grates for destruction sizes. -- It also includes Electrical panel. -- This system is apart and palletized. All you have to do is pick it up and transport it to you. -- System was in perfect working order when it was taken apart and palletized for transport. -- The system is perfect for the destruction of computer hard drives and different types of media.

SCM M3 Multi-Blade Dip Chain Gang Rip SawSpecifications: -- 300 mm (11.81") Width cap. -- 110 mm (4.33") Max. depth of cut. -- 8-3/4" Throat depth. -- 390 mm (15.35") Min. stock length. -- 200 - 350 mm (7.87" - 13.78") Blade diameter. -- Arbor dia. 70 mm (2.76"). -- Table size 750 x 1,530 x 750 mm H (29-1/2" x 60.24" x 29-1/2" H). -- Blade speed 4,200 RPM. -- Feed speeds 6 - 48 MPM (19 - 157 FPM).Equipped with: -- 44 kW (60 HP) - 3,554 RPM Blade motor. -- Variable speed drive feed chain motor. (2) Upper infeed & (2) Upper outfeed 4" Dia. rollers, Automatic chain lubrication. -- Top & bottom anti-kickback fingers. -- Main dust hood, with 200 mm (7.87") Dia. outlet. -- 40"; x 2-3/4"; H Adjustable infeed fence. -- Motor load meter.Complete with: -- Operation & Maintenance Manual. -- Tooling (As pictured).

CANTEK - C 12 RSH, ...Straight Line Rip Saw:Ruggedly constructed with cast iron & ground tables, cast iron pressure housing with (6) guide rollers, and solid welded steel base chassis.Specifications: -- Saw blade dia. 8" - 12", -- Saw arbor dia. 1", saw arbor speed 4,400 RPM. -- 16 HP Saw arbor motor, 2 HP feed motor, 45 - 120 FPM variable speed range. -- Min. workpiece length 8", max. cutting thickness 3-3/8", -- Distance from column to center of chain 18". -- Table size is 39" x 57", table height 31-1/2".Equipped with & Features -- The cast iron upper pressure housing provides a stable mounting for the precision ground & nickel chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. -- 1-Piece cast iron chain with a diamond-cut surface for positive material feeding.

CANTEK C10RSStraight Line Rip Saw --Specifications -- 12" Over cutting Rip Saw ruggedly constructed with cast iron & ground tables, -- Cast iron pressure housing with (6) guide rollers and solid welded steel base chassis -- Saw blade dia. 8" - 12", -- Saw arbor dia. 1", -- Feedspeeds of 50, 65 and 85 FPM - 4,500 RPM, --10 HPsaw arbor motor; 1 HP feed motor, --Min. workpiece length 8", max. cutting thickness 3-3/8", --13 3/4" distance between saw and column, -- 30" X 50" table size, 31-1/2" table height. --Equipped with & Features: -- Cast iron upper pressure housing provides a stable mounting for the precision ground & nickle chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. -- (1)-piece cast iron chain with a diamond cut surface for positive material feeding. --Included: Manual , and several blades and the toolkit.÷

CANTEK C-14RS Straight Line Rip Saw; Absolute straight line feeding Rip Saw. Rigid machine body consists of a thick welded steel frame with an integral table which is fitted with a sturdy cast column. Excellent precision work accuracy and durability.Specifications: -- 4.92" Max. thickness cap; 8" min. length; variable feed speeds from 50 to 120 FPM and powered by a 1 HP feed motor. -- 1" Dia. saw arbor powered by 20 HP arbor motor; swings 12" thru 16" dia. blade at 4,500 RPM; with 24" distance from blade to saw column. -- 31-7/8" From floor to top of table; table is 50" wide x 75" long.Feed System & Chain: -- Precision caterpillar chain and double "VEE" guide rails are made of special cast iron. The chain connecting pins are made of high grade steel - heat treated & ground for high durability and low wear. -- (8) Hold-down rolls for increased control and precise straight line cutting (6 rows). -- Mechanical operation Chain Oiler (Best) provides consistent lubrication to the chain track and automatically adjusts to your feed speed. When oil runs out the machine track stops running to avoid damage to track. Features: -- Precision Built Saw Arbor constructed of nickel chrome steel, large diameter, accurately ground and dynamically balanced. The arbor runs in precision angular contact type ball bearings (eliminates any radial run-out & axial thrust) - V-Belt driven from below, with easy to access adjustments and controls. -- (3) Sets of anti-kickback fingers; (2) top and (1) set in the table. -- Soft start - Star Delta starter. Telemecanique U/L magnetic starters.Options available at additional cost: -- 20mW Red Laser (FPIMLC1320WFL) & Laser Holder (FPICAN03)..................................... $ 495.00 -- Extra Saw Blade: 14";x0.157"; kerf x 1.5"; bore x 60T (CANC14RS-BLADE-14)........... $ 118.00

CANTEK C-12RSH Overcutting Straight Line Rip Saw;Ruggedly constructed with cast iron & ground tables, cast iron pressure housing with (8) holddown rollers and solid welded steel base chassis.Specifications: -- 3.35" Max. thickness cap; 8" min. length; variable feed speeds from 50 to 120 FPM and powered by a 1 HP feed motor. -- 1" Dia. saw arbor powered by 15 HP arbor motor; swings 8" thru 12" dia. blade at 4,500 RPM; with 18" distance from blade to saw column. -- Arbor runs in precision angular contact type ball bearings (eliminates any radial run-out & axial thrust) - V Belt driven from below. -- 31-7/8" From floor to top of table; table is 39" wide x 57" long. -- Rigid machine body consists of a thick welded steel frame with an integral table which is fitted with a sturdy cast column. Feed & Chain: -- 1-Piece cast iron chain with a diamond cut surface for positive material feeding and absolute straight line feeding. -- Precision caterpillar chain and double "VEE" guide rails are made of special cast iron. -- Equipped with high-frequency hardened chain Guide Rails. -- The chain connecting pins are made of high grade steel - heat treated & ground for high durability and low wear. -- (8) Hold-down rolls for increased control and precise straight line cutting (6 rows).Features: -- Easy to access adjustments and controls. -- Mechanical operation Chain Oiler (Best) provides consistent lubrication to the chain track and automatically adjusts to your feed speed. -- Equipped with: (3) Sets of anti-kickback fingers; (2) top and (1) set in the table. -- (1) 5" dia. dust outlet. -- Soft start, Star Delta starter - Telemechanique-Square D, Magnetic Wye/Delta Starters - Low Amperage Soft-Starter on the arbor motor - Electrics to UL/CSA Standards.Available Options when order with machine: --20mW Laser (FPIMLC1320W) & Laser Holder (FPICAN03) – made in N.A.... $ 495.00 -- KANEFUSA 12" Glue Joint Carbide Rip Saw Blade...$ 165.00

CANTEK - C14RS, ...Straight Line Rip SawSpecifications: --Overcutting Rip Saw. -- 4.92" Max. thickness cap; 8" min. length. -- Variable feed speeds from 49 to 128 FPM and powered by a 2 HP feed motor. -- 1-1/2" Dia. saw arbor powered by 15 HP arbor motor. -- 31-7/8" From floor to top of table; table is 50" wide x 75" long. Equipped with & Features: -- (3) Rows of antikickback fingers: (2) Top & (1) Bottom, for safe operation. -- (8) Holddown rolls for increased control and precise straight line cutting (6 rows). -- 6" (150 mm) Wide chain track runs on double-V guide rails, which are made of special cast iron for added wear. -- Magnetic Controls.

CANTEK - C 12 RSH, ...Straight Line Rip SawRuggedly constructed with cast iron & ground tables; cast iron pressure housing with (6) guide rollers, and solid welded steel base chassis.Specifications: -- Saw blade dia. 8" - 12"; saw arbor dia. 1"; saw arbor speed 4,400 RPM. -- 15 HP Saw arbor motor, 2 HP feed motor, 45 - 120 FPM variable speed range. -- Min. workpiece length 8", max. cutting thickness 3-3/8", distance from column to center of chain 18". -- Table size is 39" x 57"; table height 31-1/2". Features: -- The cast iron upper-pressure housing provides a stable mounting for the precision ground & Nickle chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. -- 1-Piece cast iron chain with a diamond cut surface for positive material feeding.Approx. (600) Hours production time.Total amperage is 21.5 amp and the gross weight is approx. 2,530 Lbs.

CANTEK - C 12 RSH, ...Straight Line Rip SawRuggedly constructed with cast iron & ground tables; cast iron pressure housing with (6) guide rollers, and solid welded steel base chassis.Specifications: -- Saw blade dia. 8" - 12"; saw arbor dia. 1"; saw arbor speed 4,400 RPM. -- 15 HP Saw arbor motor, 2 HP feed motor, 45 - 120 FPM variable speed range. -- Min. workpiece length 8", max. cutting thickness 3-3/8", distance from column to center of chain 18". -- Table size is 39" x 57"; table height 31-1/2".Equipped with & Features -- The cast iron upper pressure housing provides a stable mounting for the precision ground & Nickle chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. --:1-Piece cast iron chain with a diamond cut surface for positive material feeding.Total amperage is 21.5 and the gross weight approx. 2,530 Lbs.

CANTEK HB-800 32" Vertical Band Resaw32" Wheel diameter, 20 HP motor Vertical Band Saw;Specifications: -- 3.543" (90 mm) wheel width, 30-5/8" throat capacity, 15-3/8" under guide capacity. -- 4" Blade width X 216- 217-1/8" blade length. -- 20 HP main motor, generates a blade speed of 5,024 SFPM.Features: -- Heavy fabricated steel machine frame. -- Specially designed Bakelite guide blocks provide rigid side blade support for straight cutting. -- Large cast iron work table is precision ground & can tilt to a maximum of 45°. -- Convenient blade tension adjustment by means of a handwheel and gauge. -- Cast iron upper and lower saw wheels are precision machined and dynamically balanced. -- Rack & pinion blade guide adjustment. -- Wheel is crowned for proper blade tracking & added stability of the blade.Complete with: -- Foot brake for braking wheels & blade. -- Blade lubrication system and reservoir for lubricant keeps blades cool.Including Electrics to UL/CSA - all starters -- Auto Start-Delta control for main motor with Emergency Stop Switch -- Telemecanique brand magnetic switchHF-150A Feeder: -- 1 HP motor with variable feed speed from 16 - 66 FPM; 6" feed opening. -- Pneumatic tensioned feed roller. -- Feed pressure is adjustable. -- Feed roller opening & closing is controlled by a foot switch for operator convenience. -- Knurled steel roller.

CANTEK - C 12 RSH, ...Straight Line Rip SawRuggedly constructed with cast iron & ground tables; cast iron pressure housing with (6) guide rollers, and solid welded steel base chassis.Specifications: -- Saw blade dia. 10" - 12"; saw arbor dia. 1"; saw arbor speed 4,500 RPM. -- 15 HP Saw arbor motor, 1 HP feed motor, 50 - 120 FPM variable speed range. -- Min. workpiece length 14", max. cutting thickness 3.34" (with 12" Blade), distance from column to center of chain 18". -- Table size is 39" x 57"; table height 31-1/2". -- Amperage 46 A.Features: -- The cast iron upper-pressure housing provides a stable mounting for the precision ground & Nickle chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. -- 1-Piece cast iron chain with a diamond cut surface for positive material feeding.