SPEC AIR Model R-44SQ Dust Collector with Shaker Bag Cleaning, Abort Gate, Spark Detection, Rotary Air Locks and Relay Fan in a closed loop configuration. -- Overall Data: 46,000 CFM with approx. 6170 sq. ft. of cloth area consisting of (286) filter bags operating at 7.4:1 Air-to-Cloth Ratio (ACR). 'Can velocity' (upward) is 211 FPM. Polyester filter bags are 9" dia. x 110" long. -- Fan:/Motor: SPEC-AIR EB-44 Clean Air Fan with approx 44" dia. inlet/outlet, ground- mounted in an upblast arrangement. Fan can deliver 46,000 CFM @ 16" SP. Inspection door, and belt guard. Belt-driven by a TOSHIBA 200 HP High Efficiency (Inverter Duty), TEFC motor, 447T frame at 1780 RPM. -- Bag Cleaning: Via (2) Shaker motors with a lattice of tie-rods inter-connected to each row of bags. Bags are accessed from the top clean air plenum.Timer relay from low voltage controls for bag cleaning. -- Comes with: (2) Tapered hoppers separating the large particles, large access door, Backdraft Dampers adapted to (2) 32" filter inlets, lower hopper bottom each with Rotary Air Lock. Discharge from both RAL's is connected to a Material Handling Transfer/Relay fan into an enclosed container (not included) for continuous collection of waste. A return pipe from container makes this a closed loop configuration. Explosion doors. Safety ladder to top return air plenum.. Magnehelic differential pressure gage to monitor the condition of the filter bags. -- Construction: Heavy gage construction with reinforcing ribs and Flange-bolted in the middle easily allows units to transport into two units, ie 120" x 141".Return Air starts from filter outlet with adaptor to 44" dia. fan inlet. Discharge Silencer of fan outlet has a 44" Abort Gate returns air into building. -- Features: HANSENTEK Spark Detection system. Main electrical panel with pushbottons and controls. -- Includes: Filter housing and outside pipe is fully covered with insulation to minimize heat loss & reduce plant heating cost. -- Overall dimensions: 282"; Long x 120"; Wide x 317"; High. Weight approx. 20,000. Lbs. -- Note: Unit was moved in 2020 to current location, refurbished added installation.

SPEC AIR Model R120-26RD-OC Baghouse Filter Auto Shaker Type Dust Collector Loaded with features. -- Capacity of approx.15,500 CFM and the following features and components: -- EB-26, 60 HP SPEC AIR, Air Handling Fan , 15.500 CFM @ 16" SP mounted in a negative pressure configuration (clean air side) with return air and with automatic 26" dia. Abort Gate Damper according to NFPA-68-69 CODE. 110 volt actuated by the Spark Detection System. -- HANSENTEK AN104 Spark Detection/Suppressions system Per NFPA 64-68 and c/w BPS-9X4 Booster Pump & FLEXCON P2P20 Tank. -- 1,961 sq. ft. of filter area using (97) high efficiency Polyester bags. Operating at 7.9 to 1 ACR (Air to cloth ratio). -- 26"; Diameter Inlet & outlet duct. -- Tangential inlet with Backflow Damper, according to NFPA-68 CODE. -- Top mounted motorized bag shaker. mechanism powered by 1.5 HP. -- Rotary Air Lock with 96" clearance. (4) leg support steel frame & Safety access ladder. -- Explosion Venting Doors, according to NFPA-68 CODE. -- Filter Bag size approx. 9" dia. x 9' long, -- Inline 26" dia. Silencer muffler on return air duct. -- Ground mounted Belt Driven Fan complete with TEFC motor and inspection door. -- Features: 60 HP Soft Start Controller. -- ENGINEERED ELECTRIC Control Panel with starters and controls. -- Manometer gauge to monitor differential pressure (life) of filter media. -- Housing/Support Steel dimensions: 120" long x 120" wide x 32' high. Approx. 13, 500 Lbs. -- Some pictured pipe is included.

SPEEDAIRE - 4B228D, ...Portable CompressorSpecifications: -- 6 HP Reciprocating Air Compressor; Pump # 4B247A; 10.3 SCFM @ 90 PSI; 9.1 SCFM @ 135 PSI. -- Max. pressure rating: 135 PSI; 26-Gallon horizontal air receiver on (2) wheels; motor and flywheel guard.6 HP Motor, wired for single-phase, 240 Volts, 15 Amp. -- Complete with: -- Single-stage Compressor head; air pressure regulator gauge, and tank pressure gauge; start-stop auto or manual cycle controls; pressure relief valve. -- (1) Air discharge port with quick disconnect.

SQUARE D - 75T3H, ...75 KVA, 480 - 208 V, 3-Phase Autotransformer Specifications: -- Intended for power, heating, and lighting applications. -- Enclosure Rating: NEMA 2. -- Multi-Tap (432 - 504 V) Primary 480 V (Delta); Secondary 208Y / 120 V @ 60 Hz ventilated. -- Aluminum windings. -- cULus Listed. (2) Available; price per unit. - Make offer for both!

SSI Model - 1000-E, Slow Speed, High Torque ShredderSpecifications: -- 50 HP Motor; twin shafts; 40" x 25" ChamberIncludes: -- Stand, feed hopper; controls

STAR V MACHINERY SCG-1600 AUTOMATIC CROSS GROOVER:: -- Specifications:(1) Spindle with 12 HP - 3,600 RPM motor, 60" max. crosscut cap., material thickness 0.25" - 1.125". (1) Internal 60" Stroke Tape Applicator Station. -- 96" Stroke Servo Motor Driven Rear Pusher Fence (Full 60" Rear Table Width), 96" Long x 20" Front Table with 5 Digital Manual Stops. -- Rear Fence Movement, Cutter forward Speed Cut/Tape Stroke and All Controls for Start/Stop, On/Off, Axis position Displays on 10" Touch Screen Panel HMI. -- Grooving Head up & down movement via pneumatic cylinder with linear rail & linear bearings, depth fine adjustment with special threaded adjustable unit. -- Carriage cross-travel powered by a 3 HP hydraulic motor (4GPM), driven ball screw with linear rail & linear bearings; feed rate from 0 - 40 FPM; Heavy Duty welded frame construction. -- Complete with:Safety guards and cutter guards; pneumatic support fence; (1) heavy-duty in-feed/out-feed roller tables. Available Options at additional cost:ACCESSORIES, TOOLING AND TAPE "CHOOSE AND ADD TO MACHINE BASE PRICE" Cove Corner Plug Jig $575.00 ea. Brazed Carbide 90 Degree Cutter for up to 1/2" Solid Surface $745.00 ea. Please specify the Material Brazed Carbide Cove Backsplash Cutter for 1/2" Solid Surface $1,265.00 ea. Please specify 3/8" or 1/2" Radius Brazed Carbide 90 Degree Cutter for up to 3/4" Wood Materials $940.00 ea. 90 Deg. Insert Cutter for up to 1/2" Thick Material (Body Only) $1,265.00 ea. Requires Below Inserts90 Degree V Insert for up to 1/2" Thick Material, $32.00 ea. Minimum of 12 Inserts Required $384.00 Carbide Insert Cove Backsplash Cutter Head for 1/2" Material (Body Only) $1,590.00 ea. Please specify 3/8 or 1/2 RadiusRequires Below Inserts 3/8" Cove Radius Insert for 1/2" Thick Material $42.00 ea. Minimum of 12 Inserts Required $504.00 3/8" Double 45 Degree Insert for 1/2"Thick Material $42.00 ea. Minimum of 12 Inserts Required $504.00PCD Diamond 90 Degree Cutter for up to 1/2" Thick Material $3,485.00 ea. PCD Diamond Cove Cutter with 1/2" Radius for 1/2" Thick Material $5,645.00 ea. Roll of VAC2MG, 2" (50mm) wide 1025y (937m) long Roll V Groove Tape $245.00 ea. Minimum of 3 Rolls per order = $735.00 -- Actual Model is STAR V MACHINERY SCG-1600 AUTOMATIC CROSS GROOVER:

STAR V MACHINERY SLG-2000 36 LINEAR V-GROOVER: -- Specifications:Working table dimensions are 120" long x 36" wide; Working width from 6" - infinite" (152 - infinite mm); Working length from 20" - infinite (508 - infinite mm); Working thickness from 0.25" - 1.15" (6 - 29 mm).Maximum throat clearance for linear & cross-cuts is 14.5"/24.5" (355/622 mm). -- Equipped with: (2) Independent, 10 HP - 3,600 RPM Saw Motors with "servo" control adjustment in "Y" axis & manual "Z" axis adjustment.30 mm Dia. Arbor x 76 mm (3") clamping length to accommodate wider cove backsplash, triple-fold profiles, or using it for hogging and finish cut; 9.25" (235 mm) max. Cutter-head dia.1-Saw motor is mounted on the front & 1-Saw motor is mounted on the back of the 8" x 12" x 1/2" heat-treated steel heavy-duty overhead support beam.Side-to-side head travels via linear rails & bearings, manual head height adjustment via linear rails & bearings. -- Feeding System:(1) 3 HP Variable speed drive belt system with "servo" height adjustment; Feed rate from 0 - 45 FPM (12 MPM), belt feeder moves workpiece on a precision "aluminum" roller table; -- Tape Applicator: (2) Automatic Tape Applicators with "servo" adjustment, according to the Saw motor position in "Y" axis. -- Operator Interface:10" HDMI Touch Screen Display for Start/Stop, On/Off, Feed Speed & Axis Position. -- Complete with:; Safety guards and Cutter guards. Anti-Kick-back Device. Emergency Shutoff line. Dust collection requirements 4,200 CFM, collector outlets on cutter guards 5" in dia.. -- Actual model# is STAR V MACHINERY SLG-2000.

STEEL FAB 400 Gallon Vertical Air Receiving TankSpecifications: -- Tank size 36" Dia. x 6' H.

SULLAIR ES8-30H/A 30 HP Single-Stage Fluid Rotary Screw Air Compressor, with 53,186 Run & 49,602 Load Hrs. (As of 11/2023)Specifications: -- Cap. 111 ACFM. -- Rated pressure 60 - 125/135 PSIG. -- Noise level 85 dBA.Equipped with: -- E-Profile rotor design air end. -- 30 HP 3,530 RPM Motor. -- Air-cooled aftercooler. -- SULLAIR “SUPERVISOR II DELUXE"; Microprocessor controller & graphic monitor system, with LCD Display, Touchpad, Constant pressure & temperature readout of pressure, Power failure auto restart, & Automatic start/stop.

SULLAIR LS-10, 30 HP SCREW AIR COMPRESSOR: -- Specifications:30 HP Motor, rotary screw air end, approx. 115 PSIG - 125 PSIG max; Mounted upon 150 Gal. receiver tank.Approx. Dimensions: 64" x 32" x 65"; Approx. Weight: 2,500 lbs. -- 2,630 Approx. total operating hours. Hour meter: Inoperable.

SULLAIR ES8-30H/A 30 HP Single-Stage Fluid Rotary Screw Air Compressor, with 53,186 Run & 49,602 Load Hrs. (As of 11/2023) Specifications: Cap. 111 ACFM. Rated pressure 60 - 125/135 PSIG. Noise level 85 dBA. Equipped with: E-Profile rotor design air end. 30 HP 3,530 RPM Motor. Air-cooled aftercooler. SULLAIR “SUPERVISOR II DELUXE” Microprocessor controller & graphic monitor system, with LCD Display, Touchpad, Constant pressure & temperature readout of pressure, Power failure auto restart, & Automatic start/stop. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

SULLAIR - LS12-60- HH/A/SUL, ...Rotary Screw Air CompressorSpecifications & features: -- 60 HP - 1,770 RPM Motor, rotary screw air end, 150 max. PSI, 250 ACFM; (2) asymmetrical lobe profile rotors, only make contact on a lubricated pitch line to virtually eliminate capacity or efficiency loss. Features: -- Tapered roller bearings on the discharge and cylindrical bearings on the inlet for high load carrying capacity, pressurized fluid lubrication & cooling of the compressor with rigid piping and tubing; efficient 2-stage air/oil separation with replaceable element. Complete with: -- Spin on fiberglass fluid filter; Heavy Duty inlet air filter. -- Capacity modulator stabilizes system pressure and matches output to demand (minimizes need for Air Receiver & reduces wear caused by start/stop). -- Electromechanical gauges & controls, air aftercooling; mounted on a steel frame bed with fork cutouts. -- (73,500) Total operating hours.

SULLAIR 10B-50 ACAC Rotary Screw Compressor (Open Type)Specifications: -- 50 HP - 1,770 RPM Motor, rotary screw air end, 100-110 max. PSI, approx. 180 ACFM; (2) asymmetrical lobe profile rotors only make contact on a lubricated pitchline to virtually eliminate cap. or efficiency loss. -- Equipped with: -- Tapered roller bearings on discharge and cylindrical bearings on inlet for high load carrying capacity. -- Pressurized fluid lubrication & cooling of Compressor with rigid piping & tubing; efficient 2-stage air/oil separation with replaceable element. -- Spin-on fiberglass fluid filter, Heavy Duty inlet air filter, cap. modulator stabilizes system pressure and matches output to demand (minimizes need for air receiver & reduces wear caused by start/stop). -- Includes: -- Electro-mechanical gauges & controls, air after-cooling.

SULLIVAN PALATEK D185PJD AIR COMPRESSOR (GAS/DIESEL): -- Specification:Mobile Air Compressor with JOHN DEER 4024TF281A, 2.4 L (4) cylinder diesel engine; PINTLE hitch. 29-Gal single fuel tank, 210 CFM (5.9 m³/Min.) @ 100 PSIG., idle speed 1,650 RPM, full load speed 2,500 RPM. -- Equipped with:Tapered roller bearings, adjustable pressure from 70 - 100 PSIG. large, 108 mm & 127 mm dia. twin screw air end & automatic 0 - 100% capacity control, with two stage dry type air filter, oil level sight gauge.One-piece canopy removable in a matter of minutes for ease of serviceability and maintenance. Pitched roof to allow water drainage, meets 2010 US EPA sound requirements. 15" Wheels with steel belted radial tires. -- (1,893) Hours on the unit.

SUMMIT PR-9S 2-Ram Horizontal Baler -- Motor: 60 HP. -- Main Cylinder: 9". -- Eject Cylinder: 8". -- Feed Opening: 60" x 44" x 46". -- Cranston Wire Tie. -- Infeed Conveyor. -- Loaded onto your Truck.

SWEED MODEL 517 SCRAP CHOPPER With Dump HopperFeatures: --The Model 517 XHD provides a large cutting capacity. This is the chopper of choice for custom applications or for operations converting substantial quantities of linear scrap materials. Prepared for an abusive environment, the 517 XHD has a strong 1/2"; plate steel housing. The 517 XHD also features a magnetic starter to protect workers from an unexpected restart after loss of power. The powerful air activated feedworks is controlled with a footswitch for operator safety, and is also capable of despooling scrap wire and cable from reels. --Additional safety options are available. Material Reference The recommended model of scrap chopper is determined by scrap size, scrap volume, and requested custom features. Please consult a SWEED representative to determine the appropriate scrap chopper for your application.» High-tensile bale wire» Small, solid, aluminum and copper bars» Jacketed and non-jacketed wire and cable» For other materials, consult SWEED --Electric Motor 5 HP --Infeed Opening 6 "; W x 1 "; H Cut Length 3 ½"; standard (smaller cut lengths available with different knife configurations) --Number of Stationary Knives 1 --Number of Rotating Knives 1 standard --Overall Chopper Dimensions 56"; L x 34"; W x 30"; H --Chopper Weight 1,492 lbs --Chopper Shipping Weight 1,577 lbs -- Include Stand and Gaylord

TAKEKAWA - RG-30S, ...Straight Line Rip SawSpecifications: -- 15 HP - 5,000 RPM Belt driven arbor, overhead arbor design. -- 1-1/4" Dia. arbor. -- 12" Dia. max. blade cap., 2-3/4" max. depth of cu.t -- 12" Min. part length. -- Throat clearance to the right of blade 26". -- Table size: 74" Long x 38" wide; 2 HP step feed drive, 33 - 66 & 131 FPM.Equipped with and Features: -- Automatic chain lubrication. -- Top pressure system with spring loaded rollers. -- Adjustable rip fence. -- Antikickback fingers. -- Push buttons and magnetic starters.

TANNEWITZ - XJ, ...Table SawSpecifications: -- 5 HP - 3,600 RPM Fan cooled motor, 1" right tilting arbor Table Saw with a 1-piece main table; table size 42" wide x 44-1/2" deep. -- Base formed from hot rolled steel of 5/16" thickness & welded into (1) solid unit; 10" dia. handwheels for easy adjustment of tilting, raising & lowering of arbor. -- Complete with: Extended rack & pinion adjustable rip fence for greater ripping capacity; left- & right-hand T-slot miters. -- 16" Blade dia., 4" dado width cap.; 4" cut depth at 90°; 3" cut depth at 45°. -- Equipped with: Taper pin miter with micrometer adjustment on fence, magnetic controlled off switch, and 6" dust outlet with auxiliary rear opening for easy access. -- Power safety electrical breaker box included. Please NOTE: No blade guard.

16" Blade cap., 3-3/4" max. cutting height, 5 HP - 3,600 RPM direct drive motor, arbor tilts 45ø, 44" x 40" cast iron table size, table with miter gauge slot. -- Complete with: Rack & pinion fence and large hand wheels for easy adjustments.

TASK MASTER TM-8512 DOUBLE SHAFT SHREDDERSpecifications & Features: -- TASKMASTER® TM8500 is a small grinder that delivers powerful capabilities. -- With its twin shaft design, this unit can perform in applications like no other by providing excellent feeding characteristics on a variety of solids. -- These units feature an 8.5"; wide cutting chamber with various chamber lengths. -- These versatile shredders can handle screenings, fish waste, fabrics, waste material, sludge, food waste, plant material, and much more.Features: -- 5 HP Motor -- Coarse or Finely Cut Output Configurations -- CUTTER CARTRIDGE® Technology -- Few Moving Parts -- No Stack Retightening -- Rugged Construction