AUTOQUIP 48S80 SCISSOR LIFT.8,000 Lbs Cap., electro-hydraulic operation. -- Standard 24" x 64" smooth steel platform. -- 7.5" Lowered height, 48" travel to raised height of 55.5"; internally mounted 1.5 HP Super Torque TENV motor, 2-cylinder design, (33) Sec travel time up-or-down. -- Complete with: Hand held up/down push button control with 10' cord, velocity fuse on cylinder, and maintenance locks on baseframe. -- Options: Up to 48" x 96" smooth steel platform, guarded foot pedal control, accordion skirt. -- Autoquip Series 35, Surface mounted lift. Unit is painted AQ black;

AUTOQUIP 60S25 Scissor Lift.2,500 Lbs. Cap., electro-hydraulic operation. -- Standard 32" x 87" smooth steel platform. Base frame 32" x 87". -- 8" Lowered height, 60" travel to raised height of 68"; internally mounted 1.5 HP Super Torque TENV motor, 2-cylinder design, (44) Sec travel time up-or-down. -- Complete with: Hand held, push button control with 10' cord, velocity fuse on cylinder, and maintenance locks on baseframe. -- Options: Up to 60" x 120" smooth steel platform, guarded foot pedal control, accordion skirt. -- Autoquip Series 35, Surface mounted lift. Unit is painted AQ black;

AUTOQUIP 36S40 DL Double Long Scissor Lift.4,000 Lbs. max. cap. with 48" x 120" smooth steel platform top. -- 36" Travel with a 6.5" lowered height and a 42.5" raised height; (25) Sec up and down speed. Base frame 24" x 98". -- Power unit with 1.5 HP Super Torque Motor, 208-230-460V - 3 Ph - 60 Cy, fan-cooled, Intermittent (2 minute) duty. -- Polyethylene hydraulic fluid reservoir with a capacity of 5 gallons. Supply voltage must be specified. -- Complete with; Hand held up/down push button control with 10' cord, velocity fuse on cylinder, and maintenance locks on baseframe, -- Option; Guarded foot pedal control.. NOTE: Surface mounted lift. Unit is painted AQ black;

AUTOQUIP 48S40 DL Double Long Scissor Lift.4,000 Lbs. max. cap. with 48" x 144" smooth steel platform top. -- 48" Travel with a 7" lowered height and a 55" raised height; (32) Sec up and down speed. Base frame 24" x 130". -- Power unit with 1.5 HP Super Torque Motor, 208-230-460V - 3 Ph - 60 Cy, fan-cooled, Intermittent (2 minute) duty. -- Polyethylene hydraulic fluid reservoir with a capacity of 5 gallons. Supply voltage must be specified. -- Complete with; Hand held up/down push button control with 10' cord, velocity fuse on cylinder, and maintenance locks on baseframe, -- Option; Guarded foot pedal control.. NOTE: Surface mounted lift. Unit is painted AQ black;

BAKER C 4-HEAD Horizontal Resaw w/Powered Return6" Wide x 12" high cap. Resaw; standard spring blade tensioning system;Specifications: -- 13'-2" x 1-1/4" x 0.035 blade provides thin kerf savings; quick & easy blade height adjustments. -- Wheels: 28" Dia. CNC machined, dynamically balanced, all-steel band wheels, (4) bolt flange; rough top feed belt combines with opposing side feed rolls and air pressure hold over rolls; idler hold downs . -- (4) 20 HP Total Enclosed Fan Cooled Motors; Thin-kerf technology and the Baker Low Profile Flat Guide System generates up to 60-70% less sawdust and up to 25% more boards, easily out-producing a gang rip. Complete with: -- Hydraulic variable feed speed from 20 to 120 FPM (6 to 36 MPM) with a tank, flow control and remote feed shutoff; powered side feed rolls. Includes: -- Powered conveyor, powered return conveyor, NEMA electrical panel with the starters, motor overload protection, remote start/stop stations.6" x 6" Square dust collection with a 90° adapter chute to a 4" dia. outlet (can be rotated in (4) directions); 600 CFM required for each drop.

BAKER ABX Single-head Horizontal Resaw The Baker "ABX" Band Resaws are designed to save space but give you the same great features of larger band resaws.Specifications: -- 12" x 12" Cut cap.; 28" precision machined wheels and 30 HP TEFC motor for main drive (40 HP optional); 2 HP hydraulic feed system with a 10-gallon reservoir, flow control valve for variable feed speed of 0 - 95 FPM; with filter, & remote feed shut off, and powered infeed. -- Features: -- Powered head rise/fall system with 40:1 ratio; endless flat belt infeed w/floating overhead feed rollers, each is hydraulically powered; spring blade tensioning. -- 3/4" - 12" Cutting width, 1/4" - 12" cutting height, uses 0.035" x 1" x 14'-2" blade length; BAKER flat guides for higher production, accuracy & extended blade life. -- Includes: -- Hydraulically-powered infeed hold-down.

BALEMASTER 772 AO WIDE MOUTH HORIZONTAL BALER -- 25 HP motor -- Dual door cylinder -- Bale size 48" W x 26" H x 48" L -- Feed chute cross section 46" W x 48" L -- Air to Oil cooler included -- Number of bale ties 5 -- Loaded on your truck

BALEMASTER - 4550G-10: Auto-Tie Horizontal BalerSpecifications: --27"; x 40"; Opening. -- 50 HP. -- 10"; Cylinder. -- 30"; x 40"; x Variable Bale.

BALEMASTER - EO-650: Horizontal Auto-Tie Baler Specifications: • 25 HP Motor.• 8"; Main Cylinder.• Hopper Opening: 46";x 50";.• Bale Size: 48"; x 30"; x (variable).• Main Ram Face Pressure: 75 PSI.• System Pressure: 2,000 PSI.• Total Compression Force: 100,500 Lbs.

BALEMASTER E-1290 Auto-Tie Horizontal Baler with AMERISHRED AMS-7500 Shredder/Conveyor/TipperBaler Specifications: -- Cylinder: 10" -- Bale size: 36" x 40" x variable -- Motor: 75 HPShredder Specifications: -- Cut: 5/8" -- Motor: 75 HPSystem equipped with: -- Enduraveyor Baler Feed Conveyor -- Discharge Conveyor -- Metering Feed Conveyor -- Cart Tipper

BALEMASTER - 760AO, ...Horizontal Closed Door BalerSpecifications: -- Cylinders: (2) 6" -- Feed opening: 60" x 40" -- Bale size: 48" x 72" x 34" -- Main motor: 25 HPEquipped with: -- (4) Wire single-loop bale ties -- Heat exchanger -- Photo-eyeNote: Dog ear springs need to be replaced and a small leak by the motor; otherwise, in great condition.

BALEMASTER - 48 X 72, ...Horizontal Closed Door Baler -- Designed for baling of whole or flattened corrugated boxes. -- Large feed opening to accommodate feed of larger material. -- Large 48" x 36" x 72" bale; weighs up to 1,700 pounds. -- Perfect for a Qarehouse application. -- 25 HP Moroe

BALEMASTER - HD-60, ...Closed Door BalerSpecifications: -- Main motor: 20 HP -- 8" Cylinder -- Bale size 48" x 30" x 60" -- Feed opening: 57" x 35"Equipped with: -- Touchscreen controls with ALLEN BRADLEY - Micrologix, ... PLC 7" QuickPanel -- Electrical disconnect switch installed on Baler -- Ground feed oversized hopper -- Totally enclosed fan cooled (TEFC) High-Efficiency motor -- Windowed Feed Chute Door with control circuit Interrupter (Limit Switch) -- Shear Blade -- Cycling eye mounted in the frame -- Low Oil Level & Hot Oil Temperature Sensors

BALEMASTER 4025G-8 Auto-Tie Horizontal BalerSpecifications: -- Cylinder: 8" -- Main motor: 25 HP -- Feed opening: 32" x 27" -- Bale size: 30" x 36" x VariableEquipped with: -- 5 Wire TieNOTE: Shear not included.

BARKER Boiler and Fuel System built & tested in 2011 as a pilot unit. Successful testing has been completed. This surplus equipment includes the following main features: -- Combustion Temp Capability- 2,000 deg.F.; Steam Flow 24,000 lbs/hr saturated; Steam Pressure 1,500 PSI @ 600 deg. F. -- Fuel Feed rate - 3,000 Lbs/hr at 1/4" biomass (5% moisture) -- Heat Input - 7,500 btu/Lbs HHV @ 22 mmbtu/hr. -- All equipment has less than 2,500 actual operating hours since installation.EQUIPMENT MAJOR COMPONENTS: Combustor, Cyclonic combustion technology, Refractory lined Heat Recovery. Steam Generator. Rotary Drum Dryer for Fuel drying - capable of 30% moisture reduction (at the above combustion parameters) and 1.5 tons per hour (installed as used equipment).BALANCE OF PLANT FUEL FEED SYSTEM: Live-bottom bin, Bunker, Feed conveyors, Wood hog, Vibrating screen, Drag and screw conveyors. Boiler water system - feed pump,water and steam piping Emissions Control: All required baghouses (SJVUAPCD) California permitted. -- Now REDUCED PRICE from $1.5 million !!

DOUCET ERS-96/RS-75/AP-508 MULTI-BLADE PANEL GROOVE/RIP SAW SYSTEM:The Doucet ERS-96/RS-75 Automated Panel GROOVE/RIP Saw System is designed to GROOVE and/or RIP panels as well as edge the sides of core materials. Ideal for plywood, OSB, MDF, HDF and other composite panels.This Line was originally designed for Engineered Flooring Blanks.ERS-96 Grooving Specifications:40 HP - 3,500 RPM belt driven saw arbor motor. Material width cap. 96" maximum. Material thickness 0.5" - 0.625" maximumGrooving pattern on 4" centers across the 96" width of panel. Depth and width of groove approx. 3/16" kerf/width by 1/8" deep.3" dia. Arbor shaft with 1.5 HP motor for motorized arbor adjustment for panel thickness. Saw arbor accessible from above for tool changes. -- Feed system:5 HP - 1,750 RPM feed motor, variable feed speed up to 75 FPM.(4) Powered bottom feed rollers & adjustable top idler pressure rolls with positive panel support during grooving operations.Top & bottom feed rollers have slip resistant urethane covered rollers, feed rollers are chain driven with air tensioning. -- Complete with:Dynamic saw arbor brake; Infeed anti-kickback fingers; Saw blade safety interlock cover; 12" dia. dust collection outlet (4,000 CFM required). RS-75 Ripping Specifications:40 HP - 3,500 RPM belt driven saw arbor motor. Material width cap. 60" maximum. Strip width cap. 2.5" minimum. Depth of cut 0.25" - 0.75" (6 - 19 mm) maximum.3" dia. Arbor shaft with 1.5 HP motor for motorized arbor adjustment for panel thickness. Saw arbor accessible from above for tool changes. -- Feed system:Doucet AP-508 Automatic panel feeder with scissor lift to automatically feed panels as needed.5 HP - 1,750 RPM feed motor, variable feed speed up to 75 FPM.(4) Powered bottom feed rollers & adjustable top idler pressure rolls with positive panel support during grooving operations.Top & bottom feed rollers have slip resistant urethane covered rollers, feed rollers are chain driven with air tensioning. -- Operator Interface: Doucet OI/HMI Control System for automatic loading & stacking with minimal human intervention other than a forklift operator to bring in new material and remove the processed parts/strips. -- Complete with:Dynamic saw arbor brake; Infeed anti-kickback fingers; Saw blade safety interlock cover; 12" dia. dust collection outlet (4,000 CFM required). -- Options Include: (1) Doucet AP-508 Automatic panel feeder with Indexing scissor lift. (1) Cross Transfer Chain Conveyor to feed panels sideways by the long edge through the Groover, max width 96". (1) Cross Transfer Chain Conveyor to feed panels short end wise through the panel RIPSAW, max. width 60" (1) Outfeed Lift Table to automatically stack ripped strips. Maximum weight of stack: approx. 5,000 LBS. -- Actual Model is DOUCET RS-75/ERS-96/AP-508

DURA-QUIP - VC-3532, ...Vibrating Conveyor: -- Specifications:35" Wide x 32' Long; Pan is 7" deep and has 1/4" round holes punched plate in most of length to allow sawdust to drop outside of Conveyor. -- Bottom frame is filled with concrete 12" deep and rests on coil springs to isolate vibration from the ground. Buyer to replace screens. -- Include: 10 HP TEFC 460 V Drive motor.

DUST TECHNOLOGY DT-50 Modular Dust Collector5 HP BALDOR Motor, compact 2-bag free-standing & self-contained Heavy Duty Dust Collector, rated @ 2,400 CFM, 9" - 11" static pressure at fan. -- Equipped with: 10" Inlet dia., (2) Cotton Filter bags with 66 sq. ft. filter area and (2) Plastic Collection Bags w/ 30 cu. ft. collection capacity. -- (2) Double "T" Bolt Straps and (2) Quick Release Metal Straps. Includes: Magnetic Starter

DUST TECHNOLOGY DT-150 Modular Dust Collector Free-standing self-contained internal air system, 15 HP Motor, rated for 6,000 CFM, 4-bag unit, 60 cu. ft. collection capacity. -- (4) Upper cloth filter bags with 133 sq. ft. filter area; 14" inlet dia., dust baffling system to fill bags evenly. -- Includes: 15 HP motor, magnetic starter, (4) Upper cloth filter bags with 133 sq. ft. filter area and (4) lower plastic disposable collection bags

DUST TECHNOLOGY DT-75 Dust Collector7.5 HP BALDOR Motor, compact 3-bag free standing & self-contained heavy-duty dust collector, rated @ 3,450 CFM, 9" - 11" static pressure at fan. -- Equipped with: 12" Inlet dia., (3) upper filter bags with 99 sq. ft. filter area (patented BEANE bags designed to be 99% efficient to .5 microns). -- Dynamically balanced sand cast poured aluminum high quality impeller with easy access; 45 Cu. ft. collection cap., dust is collected in 6-mil thick clear plastic or canvas collection bags for easy disposal or reuse, a unique adjustable baffling system assures even filling of bags. -- Includes: Manual motor starter with thermal overloads & push button station.