Newman S282 Planer

Newman S970 Planer 30" x 10" capacity 50 HP top/Bottom motors 5 hp feed motor straight knives with grinder

Newman K20 Trim Saw (2) Blades - Aprox 20" diameter Infeed & Outfeed decks

Newman End Trimmer K 20 MAXIMUM CUT LENGTH: 20' (6.1 m) 20' (6.1m) MINIMUM CUT LENGTH: 6' (1829 mm) 4' (1219 mm) 6' (1829 mm) MAXIMUM CUT THICKNESS: 7? (178 mm) 7-1/2? (190 mm) ACCURACY: +/- 1/32? (0.8 mm) +/- 1/32? (0.8 mm) FEED SPEEDS: 20 to 60 FPM (6.1 to 18.3 m/min.) FEED CHAINS: #60 roller chain #60 H type mill chain FEED DRAGS: 6 at 22? (559 mm) intervals 6 at 22? (559 mm) intervals SAW BLADES: 22? (559 mm) carbide, 60 teeth 1-1/2? (38.1 mm) bore, 10 gauge (3.4mm) 2 FLOOR SPACE: 20'-8? (6.3 m) x 6' (1.8 m) 20'-8? (6.3 m) x 6' (1.8 m) WEIGHT: Approximately 3500 lbs. (1590 kg) Approximately 3500 lbs. (1590 kg) 1`fixed saw and 4 movable saws 7.5HP each new electrical starters 1.5HP variable speed drive

Seller bought this saw with the intention of rebuilding it. He has most of the parts and started the work, but needs the space in the shop immediately. The first few photos are of the machine as it sits now (stripped). The next few show the machine BEFORE they started working on it. Newman KM16 Trim Saw Unscrambler Misc parts - shown in photos - everything going with the saw

Newman G200 Knife Grinder

Manufacturers Specifications Max Width of Material: 12 in 12-14” blade capacity Production Rate: 45-50 cuts per minute designed for 45 degree vertical cuts Work Tables: 60 inches to the right and left of the saw, Motors: (2) 2.5 HP (3,600 RPM). 220/60/3PH.

Northtech MRS-12N Gang Rip 50 HP Motor Needs a new safety with on the door

Northteck MRS-14-DXL 460v Manufacturer notes: This is a very popular machine and cost effective. New open ended design allows for you to cut wide material up to 27-1/8? wide. Plus spare arbors, lasers, and the optional quick locking, easy to adjust infeed will not break the bank. The Northtech heavy-duty 50 HP multi-rip (“gang-rip”) saw with 15? maximum blade diameter quickly and accurately cuts material up to 4-15/16? thick and 27-1/8” wide. Cutting both sides of your blanks at once provides incredible parallelism, reducing required moulder allowance, and increasing your yield. Laser guides (one included) and an optional 103” fence make proper alignment of even the longest material simple and precise. Variable feed speeds of 25 – 120 FPM and powered height adjustment further improve operator efficiency.

Northtech NT-6255 Shaper

Northtech NT 16R-10 Tilting Arbor Table Saw Infeed Roller 10 HP Motor

6” x 24” capacity 2 sided knives on helical cutter head 534 hours in meter

Northtech NTM-660M-20HCVS Planer 24" capacity

16 HP 12 filter bags up 4 collection bags lower Lots of pipe

6” width capacity 8” thickness capacity 30 hp main motor, 1.4 hp feed motor 3 hp blower motor…460 volt 3 phase 559 rpm blade speed digital oiling

Northtech 12" Resaw Model NT-HBR12V Self contained hydraulic pack

Northtech Chop Saw

Has (2) Blades Will cut up to a 12 x 12" Powered by (2) 20 HP 460 Volt 3 Phase motors Runs (2) 1 1/4" band blades Excellent Condition, (new condition with less than 4 hours use).

- Close link chain vs. open (no dust or pinch point) - Oiler has twice the number of lube points (critical) - The VS adjustment location on the 14N. - Can cut up to 4 15/16? with 14? blade vs. the MRS-12 12? blade 3-15/16”. - Can run 12? as well on the MRS-14N - Bottom kickback fingers for added safety - Saws, with proper tooling and material, can glue line Specifications: - Main Motor Hp. = 50 Hp. - Voltage/ Freq. = 460 Volt 60Hz - Phase = 3 Phase - Amp Requirement = 35 Amps - Feed Hp. = 2 Speed 1.5 / 3 Hp. - Feed System = Feed Chain - Feed Speed = 25 – 120 FPM - Variable Speed = Variable Speed Pulley - Elevation Hp. = 1/4 Hp. - Elevation Style = Manual Wheel Adjustment - Elevation Sys. = Jack Screw / Linear Guides - Total Hp. = 53.25 Hp. - Electronics = CE Approved Components - Dual Voltage = Elevation Arbor Motors - Control Voltage = 110 Volt - Assisted Start = Wye-Delta - Pass-Line = 33-1/2” - Min. Length = 17-3/4” - Min. Width = 1/2” - Max. Width = 27-1/8” - Min. Thickness = 5/16” - Max. Thickness = 4-15/16” - Arbor Rpm = 3570 Rpm - Blade Size = 12” Tungsten Carbide Tipped - No. of Teeth = 36 Tooth - Blade Kerf = 3.5 mm - Cleaning System = Brush on Chain - Vertical Travel = 3/8” – 5” - Dust Collection = (2) 6” @ 1962 CFM - Arbor Diameter = 70 mm - Hold Down Style = Pressure Plate - Kickback Finger = (2) Top (1) Bottom Sets - Emergency Stop = Push Button - Rear E Stop = Push Button - Safety Feature = Safety Interlock Switch - Guarding = Full Cabinet Enclosure - Oiler = Automatic Mechanical Oiler - Low Oil Warning = Low Oil Shut-off - Fence Type = Adjustable - Fence Dims. = 103” Length - Frame Const. = 5/16” Steel Construction - Worktable Dims. = 27-1/8” x 64” - Infeed Table = 13-3/4” x 103” - Decible Rating = 74 dB - Net Weight = 4402 Lbs. - Gross Weight = 4694 Lbs. - Machine Dims. = 67” x 58” x 71” - Packaging Dims = 72” x 65” x 77”

Nyle PHT350 Kiln System was powered up and tested, but not put into production.