ROSE MACHINERY BDH/LC/LCFT Automated Infeed SystemAutomated, high speed Infeed System for Gang Rip Saws of all makes and models and other similar machines. -- 5-Arm Breakdown Hoist - Electric hoist accepts loads 4' wide x 4' high x 4' - 24' long; 10 HP gear motor (with brake) powers the hoist and holds the load. -- Hoist actuated through foot switches for up & down; limit switches provide max. up & down positions; (5) lifting arms tilt load at 50° allowing layers to spill onto the takeaway conveyor; 16,000 Lbs. max. lift cap. -- Landing Chain - Features: (6) Strands of roller chain; powered by a 5 HP gear motor at 60 FPM nominal rate. -- Tail end constructed with integral slide, stock transits from Breakdown Hoist; head shaft & gear motor supported by tubular steel frame with bolts to allow for leveling at installation. -- Material stops at the head end so the operator can flip & grade each piece. -- Chain races fabricated from steel, UHMW PE wear strips on the top race and on the return race; conveyor is 42' long. -- Magnetic motor starter with foot switch for operator to start & stop of the chain. -- Lateral Chain Feed Table "LCF2013-20": Feeds material 3" - 10" wide x 4' to 24' long x 1" to 3" thick; variable 50 - 200 FPM Feed rate; adjustable fence throughout 3/4" range for alignment with the Rip Saw (or other machines). -- (6) 30" long, low friction steel flattop infeed chains for long life non-marking transport; 1 HP gear motor. -- (3) Powered smooth steel & non-marking feed rolls, 2 HP gear motor; rolls & chains controlled by variable speed drives. -- (3) Overhead pinch rollers, 5" dia., urethane covered; 1st (2) pinch rollers powered by individual 2-1/2" bore air cylinders to singulate pieces onto a 2' bridge; 3rd roller keeps the board moving on the bridge; pinch rolls triggered by photoelectric cells. -- Note: Fabricated frames and appropriate parts of the items in this quotation will be painted with (1) coat of industrial grade Shady Lane Green enamel; guards and appropriate moving parts painted with Safety Orange. -- All gear motors, mechanical equipment, limit switches, sensors or photoelectric devices, as required for each item of this quotation, are supplied and mounted; all pneumatic cylinders or other pneumatic power devices and their valves supplied and mounted; connecting hoses & fittings installed. -- Filter/Regulator units supplied, mounted, and connected by hose to the valves; Note: Compressed air service to equipment is by others.

Ripsaw Feeder with 32" wide feed rolls on 18" thru 28" roll centers; will feed 3' thru 16' lumber. With 24" of in-out fence travel; feed speeds from 50 to 150 FPM; 3/4 HP feed roll drive and 3/4 HP fence drive via gear motor with brake. -- Fabricated frame of structural steel with boots that allow +/- 1" elevation adjustment. 3-1/2" dia. steel feed rolls driven by a variable frequency drive for speed adjustment; rolls are canted to aid in holding stock against the fence. -- Powered fence with 24" fence travel is easily shifted via joystick control for stock alignment with the sawblades. -- With pneumatic powered gate to keep material from feeding until the operator initiates the feed sequence. -- Urethane covered idler pinch roll is attached to the fence and is powered down at the start of the feed sequence. When a photocell detects the board is clear of the gate, the pinch roll and gate will return to their normal position. Electrical control panel ready for connection to the power supply.

ROSE MACHINERY HBR Horizontal Band RE-RIP SawThe Horizontal Band Re-Rip Saw is an effective and efficient means of ripping short blocks into as many as six (6) set rip widths. Rip widths are easily adjustable, as well as the setting for stock thickness.Advantages of the system: -- Compact, efficient use of floor space. -- Accurate cutting of rips with minimum tear-out. -- Short blocks, 4" minimum length, without taper problems. -- Straight through feed design, good for sorting. -- Minimum dust collection required. -- Single point scrap collection. -- One saw drive motor, requires less power. -- Safety, no kickback problems.Specifications: -- Five (5) rip widths - (6) optional -- 20 HP bandsaw drive -- 30" diameter band wheels, 2" wide face -- (2) 3/4 HP feed works drives -- 1-1/2 HP feed belt drive -- 1" to 6" rip width (independently adjustable in each lane) -- 10" maximum board width at maximum rip -- 4" maximum waste piece width -- 3/4" to 2" stock thickness (all lanes adjust together) -- 4" minimum stock length -- 36" maximum stock length -- 80 FPM feed speed -- 52" to 58" pass line height -- Motor starters and push buttons included, wired for 440 volt, 3 phase, 60 Hz (uses standard mag starters) -- An automatic band lubrication system is includedOptional Equipment: -- For SIX (6) LANES, add ...$5,600 (SORTER increases $3,700) -- Automatic machine grease lubrication system, add ...$ 9,200 -- Ergonomic overhead stock slide, add ...$ 5,600 -- Output conveyor and sorter for 5-LANEsingle side discharge, add ...$47,300 -- Output conveyor and sorter for 6-LANE single side discharge, add ...$51,100 -- Operator's platform, add ...$ 7,900 -- Optional voltage configuration: 220/380/440V, 50HZ, add ...$2,900 -- Start-up and training, add $1,000 per day plus expenses at costHorsepower Requirements: -- (1) @ 20 HP -- (1) @ 1-1/2 HP -- (2) @ 3/4 HPDust Collection: -- (2) outlets, 6" diameter, 5,200 FPM velocity @ 2,300 CFMCompressed Air Required: -- 90 PSI @ 1.4 CFM

SHOP FOX W1738 WIDE BELT SANDER 37-1/2" Width cap. Combination HeadSpecifications --Single Head, 37" Wide Belt Sander with a combination head. -- 4" Dia. rubberized contact drum and finish platen for a fine finish to your work. -- Efficient 10 HP Sanding belt motor. -- Popular size 25" x 60" Abrasive belts. -- Reliable Air tracking for the sanding belt.Equipped with & Features -- Electronic digital readout for manual setting of conveyor bed. -- Better designed with (4) Jackscrews to move the conveyor bed from a 0" - 5-7/8" opening. -- Variable Conveyor speeds of 13 to 65 FPM. -- (2) Each infeed & outfeed spring loaded holddown rollers.

SHRED-TECH - ST50, ...Dual Shaft ShredderSpecifications: -- Motors: (2) 20 HP. -- Cutter width: 1" Approx. -- Cutting Chamber: 20" x 35". -- Control Panel. -- Mounted on stand. -- Feed Hopper: 21" x 40" Opening.Can be shown under power.

SHRED-TECH - ST20, ...Dual Shaft ShredderSpecifications: -- Motor: (1) 20 HP. -- Cutter width: 3/4" Approx. -- Mounted on stand. -- Feed Hopper.

SHRED-TECH - ST100, ...Dual Shaft ShredderNew in 2019Specifications: -- Motors: (2) 50 HP. -- Cutter width: 1.5" Approx. -- Cutting Chamber: 32" x 60". -- Control Panel. -- Mounted on stand. -- The ST-100 Industrial Shredder is a complex, heavy-duty shredder machine that features a 32"; x 60"; cutting chamber, enabling it to handle a wide range of products and bulky wastes. It can tear through tougher loads, such as wooden pallets, metals, hazardous wastes, passenger tires, and more.Once these products go through our shredder, they end up in a smaller, optimum shred size. It works with a large-duty throughput of up to 3 tons per hour, working much more efficiently for the business

SHREDPAX AZ-45 Dual Shaft ShredderSpecifications: -- QTY 2 20 HP Motor -- Voltage 480 V, 60 Cy, 3-Ph. -- Dual Shaft -- Support Stand IncludedLoaded on your truck

SHRED-PAX - AZ-80, ...Shredder -- Dual Shaft Shredder. -- Motors: (2) 40 HP. -- Blades: 1" Width; (26) blades total. -- Crescent Moon Ram Assist. -- Ram rebuilt. -- Loaded onto your Truck.

SICOTTE J 20-5 Horizontal Boring Machine:12" x 60" Steel table with 2-1/2" manual up-and-down adjustment. -- (4) Drive groups with 1-1/2 HP - 3,500 RPM drive motor each, timing belt & pulley drive. -- (7) Spindles, 2" in dia. and with Jacob chuck 0 - 1/2" capacity. -- Spindle feed powered by 3 HP hydraulic pump, 0" - 6" stroke, variable speed up to (30) strokes/Min.Complete with: -- (3) Pneumatic holddowns, -- Cycle timer 0-30 sec., -- Automatic/manual cycle with foot pedal switch, -- Sinvle or continous stroke -- Emergency stop.

SICOTTE J3H-A-6 Angular Vertical Boring Machine24" x 72" Table size Angular boring machine for chair seat -- (6) Hydraulic self feed spindle having 3 7/8" adjustable stroke and variable speed feed, 1 HP motor, jacob chuck 0 to 1/2" capacity, mounted on 24"long arms with timing belt drive. -- The spindle can be set at coumpônd angle angle with 30 deg front to back and 15 deg right top left. -- (2) Air holddowns. -- 0" - 8" Vertical table feed hydraulically operated that can be used when you drill vetically without angle, , variable feed and table travel adjustable from front of machine, -- 3 HP hydraulic pump motor with reservoir. Complete with: -- Electrical control system with separate motor controls, -- Single or continous stroke, -- Manual and automatic cycle and foot pedal actuation, -- Selector switch to activate each spindle manually . -- This machine is design for chair seat boring or any other application where angular holes are required.

SICOTTE - J 3H-7, ...Vertical Boring Machine24" x 84" Table size. Equipped with: -- (5) 1.5 HP Motors mounted on 24" long arms with motor starter and overload relay. -- (5) 1-1/2" Dia. spindles with spring collet 1/2" capacity. -- (2) Spring loaded holddowns.Features: -- 0" - 8" Vertical table feed, hydraulically operated; variable feed and table travel adjustable from front of machine. -- 3 HP Hydraulic pump motor with reservoir. Complete with: -- Electrical Control System with separate motor controls. -- Single or continuous stroke. -- Manual and automatic cycle. -- Foot pedal actuation. -- (1) Safety guard.

SICOTTE - T 1050, ...Horizontal Boring Machine 2-Spindle Horizontal Borer.Equipped with: -- 1 HP Motor, timing belt drives with motor starter. -- (2) Horizontal spindles, 2" dia. with Jacobs® Chuck, 0 - 1/2" capacity, turning at 3,450 RPM.Features: -- 4" Boring head stroke with air/oil system and adjustable feed speed. -- Spindle mount on dovetail beam with min. 2" to a max. 11-3/4" center distance.Complete with: -- (2) Pneumatic hold-downs & 12" x 16" wooden table size.

SIEMENS - 75 KVA,... 480 - 380Y/220 Volt 3-Phase Dry Type TransformerSpecifications: -- General purpose: Intended for power, heating, and lighting applications. -- Enclosure Rating: NEMA 3R ventilated; for indoor or outdoor use. -- Multi-tap (432-504) Primary 480 V (Delta); Secondary 380/220 Volt Y - 60 HZ ventilated. -- Aluminum winding material. -- NEMA Class ANN. -- Catalog # 3F6Y075FCD16.(2) Available; priced per unit; make offer for both!

SIERRA - RB5000, ...Portable Baler/LoggerNew in 2011 - Less than 500 hoursFeatures and Specifications: -- Faster cycle times equals higher production volume. -- Features an easy-to-load loading box that opens to 16’-5"; x 8’-1"; and short-stroke rams that greatly reduce cycle times. These powerful rams crush each load with 240 tons of force per side, producing:Logging production: 16 - 22 Tons per hourBaling production: 10 - 14 Tons per hour -- The "RB5000" is the perfect machine for any scrap yard that receives appliances, sheet iron, smaller automobiles & automobile shells, clips, and busheling as their main source of material. -- The "RB5000" Portable Baler/Logger compresses logs and bales to shredder and mill specifications. -- Typical log density: 25 to 35 Lbs. per cubic foot. Average overall weight: 1400 lbs. -- Typical bale density: 80 to 90 lbs. per cubic foot. Average overall weight: 850 lbs. -- Any transfer station that receives a high volume of appliances and sheet iron can also greatly reduce freight costs by baling and logging. -- The structural details and proper design protect the key components of the "RB5000". -- The solid self-framed construction of this portable baler/logger includes SIERRA’s: Standard L-box shaped design, 11/16th-inch abrasion-resistant steel Hardox 450 liner plates, and outer honeycomb construction creating a greater box integrity and adding to the "RB5000’s" longevity. -- For added versatility, the Crane is independent of the Baler, has a continuous rotation, and is fully operational while the Baler/Logger is in use, increasing productivity. -- The Crane features 24-2/3 Ft. boom length and 4,400 Lbs capacity while fully extended and includes an orange peel grapple with a rotator that was specifically designed to handle bales and logs. The well-designed cab and agronomical controls were designed for comfort, safety, and long-term use.

SIERRA - 700T: Shear BalerSpecifications: -- Motors: (2) Electric 100 HP. -- Preload Table. -- Precompression. -- Shearing: 14 - 17 Tons per hour. -- Baling: 12 - 14 Tons per hour. -- Logging: 15 - 17 Tons per hour. -- Cylinders: (1) Main Compression ram; (6) folding box rams. -- Cylinder forces: Shear - 700 tons precompression; 115 tons main compression; 160 tons folding box; (6) cylinders @ 80 tons each; 240 tons each side. -- Folding Box Dimensions: 19 Ft. x 8 in. x 7-2/3 ft. Open: 19 Ft.; 8 in. x 32 in. x 24 in. Closed: 34 In. x 22 in.Shear Throat -- Disassembled approx. (3) years ago. -- Running when removed from service.

SIERRA - RB6000, ...Portable Baler/Logger - New in 2020Approx 9,300 HoursThe RB6000’s automatic baling and logging cycles keep you at peak efficiency. Baling: 12 - 16 Tons per hourLogging: 18 - 22 Tons per hourAutomobile Logging: 26 - 32 Tons per hourThe RB6000 baler/logger is a beast on automobiles, appliances, and lightweight sheet iron; producing logs with the density you need to meet max weight. Looking to produce mil-spec bales?The RB6000’s cylinder comes within 18 inches of each other allowing you to densely bale clips and busheling to mill specifications.Average Bale and Log specifications:Bales: Size (40 in. X 24 in. X Variable), Weight (850 lbs.)Logs: Size (40 in. X 24 in. X Variable), Weight (1200 - 1400 lbs.)The portability of the RB6000 baler/logger gives you the versatility you need with the capability of being moved to multiple locations or to different areas within the same location.The hydraulic powered outriggers provide the needed stability to handle the heavy weight of the machine.

SIERRA REB 2-250 TWO RAM BALER --New in 2020Specifications per factory: --The Sierra REB-2 two-ram baler was a machine designed by recyclers, for recyclers and is the ultimate machine for any high volume or high production facility. Available with either a 150 or 250 HP power unit, it has the ability to process a wider variety of materials at a higher rate of production and will ensure your return on your investment. The REB-2 has a unique shear blade that works on waste, fiber, non-ferrous scrap metal, and tires, so there is no need to choose between one material or the other. --To eliminate material contamination when changing materials, the REB-2 features an innovative bale eject and oversized bale release door combined with full ejection of bales. This feature also produces better bale integrity, especially on materials with lots of memory. --The standard features on the REB-2 two-ram baler gives it unmatched performance and versatility as well, expertly handling a wide range of recyclable materials:MSWUBCPETOCCONPHigh gradesAluminumNon-ferrous metalsTires MAIN MOTORS: 2 @ 125HP/480V/3PH/60HZ/TEFC• ELECTRICAL SERVICE: 480V 500 AMP• MATERIAL SETUP: 16 MATERIALS WITH 15 BALING PARAMETERS PER MATERIAL (SAVE, RESTORE AND RESET FACTORY DEFAULTS)POWER HYDRAULIC• SYSTEM OPERATING PRESSURE: 4500 PSI• SHEAR/BALING FORCE: 254 TONS• RAM-FACE PRESSURE: 304 PSI• MAIN PUMP FLOW: 564 GPM• PUMP: KAWASAKI PISTON/ VICKERS VANE• OIL FILTRATION: 5µ RETURN LINE, 3µ KIDNEY LOOP• MAIN CYLINDER: 12"; BORE - 254 TONS• EJECT CYLINDER: 8"; BORE - 113 TONS• DOOR CYLINDER: 7"; BORE - 87 TONS• RESERVOIR CAPACITY: 1400 GALLONS

SIERRA T556SLK Shear/Baler/LoggerApproximately 3500 hours only!The T556SLK shear/baler/logger was designed with strength, mobility, and time efficiency. It is available diesel or electric and is a true workhorse that doesn’t require a special foundation. After a two-day assembly process, it is ready to work for you. Easily transportable, the SLK series can be easily taken from yard to yard, and there is no need for an operator as they come fully equipped with remote-control operation.With 556 tons of cutting force, the T556SLK Shear/Baler/Logger has unmatched versatility and is ideal for scrap processors, C&D facilities, and Demolition contractors.Shear:Foundry scrap, pipe, beams, plate, HMS #1, HMS #2Shearing production: 16 - 22 tons per hourBale:Clean sheet, wire, lightweight scrap, tin, clipsSize (31"; x 25 x Variable), Weight (900 lbs. average)Baling production: 16 - 22 tons per hourLog:Appliances, automobiles, sheet metal, tinSize (31"; x 25"; x Variable), Weight (1200 lbs. average)Logging production: 18 - 22 tons per hourAs with all Sierra machines, the T556SLK is expertly manufactured with an innovative L-Box-shaped design, 11/16th-inch replaceable abrasion-resistant steel HARDOX "450" liner plates, and outer honeycomb construction, creating greater box integrity.

SIERRA - RB6000, ...Baler/Logger - New in 2008Electric with approx 12,500 hoursThe RB6000’s automatic baling and logging cycles keep you at peak efficiency. Baling: 12 - 16 Tons per hourLogging: 18 - 22 Tons per hourAutomobile Logging: 26 - 32 Tons per hourThe RB6000 baler/logger is a beast on automobiles, appliances, and lightweight sheet iron; producing logs with the density you need to meet max weight. Looking to produce mil-spec bales?The RB6000’s cylinder comes within 18 inches of each other allowing you to densely bale clips and busheling to mill specifications.Average Bale and Log specifications:Bales: Size (40 in. X 24 in. X Variable), Weight (850 lbs.)Logs: Size (40 in. X 24 in. X Variable), Weight (1200 - 1400 lbs.)