TYLER 2400 SLOT-WALL MACHINE: -- Specifications:Produces T-slot "slat-wall" for architectural/store fixtures. 4' x 8' (48" x 97") max. panel cap., 2' x 2' (24" x 24") min. panel cap., min. panel thickness = 0.5" max. panel thickness = 1.5"; The Tyler 2400 can machine up to (40) panels/Hr, depending on material density, thickness and the slot profile. -- Equipped with: (18) Router spindles all on 3" fixed centers, spindles are driven in groups of (3) with (6) 7.5 HP - 3,450 RPM motors, all router spindles rotate @ 15,400 RPM. -- Operation: Panels remain stationary on top, pneumatically clamped in place while the bottom mounted router bank traverses the full length of the panel with a high-speed return, variable feed speed control, router assembly traverses on ground & polished rails with chain drive. -- Panels are positioned along the 8' rear edge fence line, distance from the panel edge to the centerline of the 1st cut can be adjusted from 0.0" - 3" (1 router spindle pitch). -- Overhead hold-down assembly with (2) large air cylinders and (5) arms with spring loaded clamping pads hold the panel in place. Panels are loaded from the 8' front and exit to the side. -- Includes: Operator controls for the machine cycle and a "setup" mode of operation; machine cutting cycle is initiated by a 2-hand operator safety buttons located on the right front of machine. - Produces approx. (30 - 40) panels per hour. -- Available Options at Additional Cost:Router spindles on 4'- & 100-mm centers; 48" x 121" workpiece capacity increases left-to-right workpiece (length) capacity.60" x 97" workpiece capacity increases front-to-back workpiece (width) capacity & includes (1) additional multi-spindle router head.60" x 121" workpiece capacity increases front-to-back & left-to-right workpiece capacity & includes (1) additional multi-spindle router head.

UAS -BHT (CALCOR) MIB-11-T19- SVA Pulse Jet baghouse dust collector. MIB is Modular Industrial Baghouse. -- Has qty (18) each of filter bag # 04007500 (6.125 x 75") and qty (18) each of filter bag # 0400000249 (6.125 x 41.6250"), for a total 1,896 sq. ft with pleated Spunbonded Polyester w/PPTFE filter bags. -- OEM rated for 5,000 ACFM @ 11" SP, resulting in a 2.64 Air-to-cloth ratio. -- 20 HP Siemens motor, on a large floor-mounted blower -- Comes with DPC and Timer board for Pulse Cleaning Control. Allen Brady Starter and air quality motoring. -- Discharges thru Pyramid hopper into a 55 Gallon Drum. Includes explosion relief door. -- Housing dimensions: 60" x 60" x 232" high. Total weight with filters: 3800 Lbs. -- Looks like its brand new. -- Last used for a CNC Laser Cutter.

UHLING - HP-3000: Case Clamp (Single-Bay) -- Specifications:Clamping Capacity: 55" L x 96" H x 24" D; Large enough for multiple boxes. - Offers versatility, quick 30-second setup or changeover. Pressure Elements: -- (4) Dual air pod pressure bars that are pneumatically activated and counterweight balanced; position them effortlessly and let go. The counterweight keeps them in place; no need to secure them! -- Air Pod Stroke: 3-1/2" Stroke of air pod with 0 - 120 PSI pressure adjustment. -- Vertical Beam: Moves easily on roller bearings with pneumatic carriage locks; (4) small air cylinders from (1) control point. -- Operator Control Panel: Mounted on vertical beam, so it is always where it is needed; single-lever lock-or-unlock control & front/rear pressure selection.

UHLING HP-3000 55" L x 96" H x 24" D Single-Bay Pneumatic Case Clamp Specifications: Clamping Cap. 55" L x 96" H x 24" D, Accommodates multiple boxes. Air pod stroke 3-1/2", Pressure adjustment 0 - 120 PSI. Setup time (25) Sec., Changeover time (30) Sec. Equipped with: Vertical beam, with (3) Counterweight-balanced & (1) Stationary 24” W x 5-3/4” H dual air pod pressure bars, Roller bearing mounted carriage with Pneumatic locks, Adjustable in 5” increments. Solid back support. Adjustable squaring arms. Carriage mounted control panel, with Single lever lock & Individual air pod selection. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

UHLING - HP-3000: Case Clamp (Single-Bay) -- SpecificationsClamping capacity: 72" L x 74" H x 24" D; Large enough for multiple boxes; offers versatility, quick 30-Sec setup or changeover. -- Pressure Elements(4) Dual air pod pressure bars that are pneumatically activated; counterweight balanced; just position them effortlessly and let go: Counterweight will keep them in place; no need to secure them! -- Air Pod Stroke3-1/2" Stroke of air pod with 0 - 120 PSI pressure adjustment. -- Vertical BeamMoves easily on roller bearings; pneumatic carriage locks with: (4) Small air cylinders from (1) control point. -- Operator Control Panel:Mounted on vertical beam so it is always where it is needed; single lever lock-or-unlock control & front/rear pressure selection. -- Counter SupportBy solid laminated panel opposite to pressure bars. -- Actual Model is: UHLING HP-3000

UHLING HP 4000 Case ClampThe most versatile, quick and easy-to-use Case Clamp on the market!Specifications: -- 100" x 50" x 24" Clamping cap. that's UHLING's most versatile Clamp ever. -- (3) Counterweight balanced, fully adjustable horizontal dual air pod pressure bars and (2) vertical, easy adjustable dual air pod pressure bars. -- 3-1/2" Stroke with individual controls for each air pod pair. -- Roller bearing mounted carriage with pneumatic locks (considered to be the fastest 2-axis Clamp on the market). -- Single lever lock-or-unlock control and front/rear pressure selection. -- Solid panel counter support that is opposite the pressure bars. -- Easy access operator's control panel that's mounted on the vertical beam. -- Approximately (30) Sec or less changeover time. -- Options: Additional dual pod pressure bar assembly for vertical or horizontal.

UHLING HP-3000 CASE CLAMP (SINGLE-BAY): --Specifications:Clamping Capacity: 55" L x 96" H x 24" D; large enough for multiple boxes. Offers versatility, quick 30-second setup or changeover. -- Pressure Elements:(4) Dual air pod pressure bars that are pneumatically activated; counterweight balanced; position them effortlessly and let go. The counterweight keeps them in place; no need to secure them! -- Air Pod Stroke:3-1/2" Stroke of air pod with 0 - 120 PSI pressure adjustment. -- Vertical Beam:Moves easily on roller bearings with pneumatic carriage locks; (4) small air cylinders from (1) control point. -- Operator Control Panel:Mounted on vertical beam, so it is always where it is needed; single-lever lock-or-unlock control & front/rear pressure selection. -- Counter Support by:Solid laminated panel opposite to pressure bars.

UHLING HP2000 Case Clamp (Pneumatic)Offers a compact, quick and easy-to-use Case Clamp.Specifications: -- 50" x 42" x 24" Clamping cap. that can handle 80% - 90% of your case good needs. -- (2) Counterweight balanced, fully adjustable horizontal dual air pod pressure bars. -- 3-1/2" Stroke with individual controls for each air pod pair. -- Roller bearing mounted carriage with pneumatic locks. -- Single lever lock or unlock control and front/rear pressure selection. -- Solid panel counter support opposite to pressure bars. -- Easy Access operator's control panel that is mounted on the vertical beam.

UHLING HP-4000 ... is a versatile, quick and easy-to-use Case Clamp.Specifications: -- 100" x 50" x 24" Clamping cap. that's UHLING's most versatile Clamp ever. -- (3) Counterweight balanced, fully adjustable horizontal dual air pod pressure bars and (2) vertical, easy adjustable dual air pod pressure bars. -- 3-1/2" Stroke with individual controls for each air pod pair. -- Roller bearing mounted carriage with pneumatic locks (considered to be the fastest 2-axis Clamp on the market). -- Single lever lock-or-unlock control and front/rear pressure selection. -- Solid panel counter support that is opposite the pressure bars. -- Easy access operator's control panel that's mounted on the vertical beam. -- Approximately (30) Sec or less changeover time. -- Options: Additional dual pod pressure bar assembly for vertical or horizontal.

UHLING HP-3000 Case Clamp ... offers versatility, quick (30) second set-up or changeover. -- Clamping Capacity, 55"- L x 96"- H x 24"- D, that's large enough for multiple boxes. -- Pressure Elements, (4) horizontal @ with (3) individual air pods, counter-weight balanced, position them effortlessly and let go, the counter-weight will keep them in place, no need to secure them! -- Air Pod Stroke, 3-1/2" with individual controls for each air pod set. -- Vertical Beam, moves easily on roller bearings with pneumatic carriage locks. -- Operator Control Panel, mounted on vertical beam, so it is always where it is needed, single lever lock-or-unlock control & front/rear pressure selection. -- Counter Support, by solid laminated panel opposite to pressure bars. OPTIONAL: Top Clamping, removable top pressure element for applications such as a vertical center partition or similar needs, removes easily if not needed. Add $ 1,000.00 to standard machine price.CUSTOM:HP-3000 F, ... comes with a "Solid Floor" for easy clamping of upper cabinets, add $ 1,000.00 to standard machine price.HP-3000 M, ... clamping capacity, 60"- L x 96"- H x 36"- D, that's large enough for deep commercial Case Goods. Please call for pricing.

ULTRA GL-630H Feed Through Moulder: 6-Head (B-T-R/L-T-B), "Flooring" working capacity of 12" x 6".Specifications: -- Head sequence: Bottom 25 HP, top 30 HP, right 20 HP/left 20 HP (opposing), top 25 HP, and bottom 25 HP motor. -- Spindle dia. of 1-13/16" with cutterhead speed of 6,000 RPM; all spindles with high prevision bearings. -- Auto. positioning of the left & top spindles radially; all additional spindles with digital readouts, including chipbreaker & pressure elements. -- Pneumatics on all chipbreakers, pressure elements, and holddown rollers. -- Horizontal spindles with HydroLock outboard bearings on #1, #2, #5 & #6. -- Straight jointer on spindles #5 & #6; Profile Jointers on spindles #3, #4, #5 & #6. Equipped with: -- Inverter controlled feed drive, variable speed of 26 - 260 FPM. -- Infeed table 1.2 M (4') with all table plates & fences hard chromed to RC 70. -- Machine table includes: (5) Table rollers for smooth through feed; short stick attachment for through feed on pieces down to 230 mm. -- Electrical cabinet & pedestal for machine controls separate from machine, Heavy Duty sound enclosure. -- Includes Startup training and Warranty!

WEIMA WLK 15 Vertical Hopper-fed Low Noise Grinder Specifications: 59" x 59" Weima WLK-15 E-Rotor Shredder, 150 HP AC Motor15" Diameter RotorFilm & Fiber Rotor90 RPM Rotor Speed(63) 50MM CuttersBolt-In Cutter Holders3" Screen90" In-Feed HeightNEW Control Panel460/3/6010" Air-Veyor DischargeNew In 2007, Refurbished In 2023.NEW CUTTERSNEW CUTTER HOLDERSNEW BED KNIVESNEW BED KNIVE HOLDERSNEW RAM GUIDES - SIDES, TOP, AND BOTTOMNEW SLIP LEDGEOVER $45,000 In New WEIMA OEM Parts Installed$25,000 Spent On New Control PanelApproximate Dimensions:Shredder: 132" L x 111" W x 90" HControl Panel: 38" L x 18" W x 60" HHydraulic: 44" L x 36" W x 42" HWILL REQUIRE WIDE LOAD TRUCK

WEIMA - TH 614 HD : Metal Briquette Press w/WEIMA 4-Shaft Shredder & ConveyorProduces 60 mm dia. x 4" (100 mm) long compacted logs; approx. 1 cbm square vertical hopper.Specifications: -- 18 HP Motor; vertical hydraulic ram compacts the material in the extrusion chamber to produce uniform material; extrusion chamber is continually filled via rotary screw type auger. -- Volume reduction from chip/dust to block up to 10:1 approx. -- Includes: -- Metal package for TH 614 HD ; catch pan with level switch; 1 x 45°; 1 x 90° & 1 x straight).Shredder 4-Shaft Shredder with electrical cabinet & controls.Specifications: -- Dual drive motors: (2) 11 kW (15 HP) Drive motors; hopper opening measures 39.4" x 55.1" (1,000 x 1,400 mm); cutting chamber opening of 18.2" x 27.6" (462 x 700 mm); rotor length of 18.2" (462 mm); rotor speed 25 RPM; cutting disc 11" (280 mm) diameter.JORGENSEN - Transfer Conveyor18" Wide steel belt; collection hopper for under "ZMK 30" Shredder; coolant pump and float switch for fluid transfer.

WEIMA ZM-40 Quad Shaft 4-Shaft ShredderEquipped with: -- Dual drive motors - (2) 30 HP Drive motors. -- Hopper opening measures 51" x 55.1" (1,300 x 1,400 mm); cutting chamber opening of 30" x 27.6" (762 x 700 mm). -- Rotor length of 30" (762 mm); Rotor speed 25 RPM; cutting disc 11" (280 mm) diameter. -- Complete with: -- Control Panel with soft start and 16' cable bundle. -- Note: "Quad Shaft" Shredders, unlike Dual Shaft Shredders, allow shredded material to be circulated through the cutting chamber until it is small enough to pass through the sizing screen. -- Machine weight: 5,500 Lbs.

WEIMA ZM-30 Quad Shaft 4-Shaft ShredderEquipped with: Model- ZM 30 S -- Unit was used to shred wire (6,000 – 8,000 lbs per hour) --20mm screen included 25 HP x 2 --480V- 3 phase --Cutting chamber is 19"; x 27"; Hopper is 33"; x 48"; --The ZM30S is a beefed up version of the ZM 30. Unit has the same size motors, shafts and cutters as the ZM 50 but with a shorter shaft length

WEINIG Powermat 1000 7-Head Feed Trough Moulder(B-R-L-T-T- B-U); working cap. 9-1/16" x 4-3/4". Head sequence: -- Bottom 15 HP, Right 15 HP, Left 15 HP, Top 30 HP, Top 40 HP , Bottom 30 HP, and Universal 15 HP motor. All motors with electronic brakes. WEINIG Touch-Screen "Power Com" -- PowerCom Plus software system features: Profile drawing storage, profile dimensions, tool changes and production optimization. -- Electronic LED readouts for all tool holder settings, including chip breakers & pressure elements.Spindle arrangement: -- Spindle #1: 1-13/16" w/Cutterhead speed of 8,000 RPM; -- PowerLock tool holders on #2 - #5 with 12,000 RPM, universal tool holder variable from 4,000 to 12,000 RPM and with high precision bearings; -- Adjustment of vertical tools 2-3/16" axially. -- Motorized tool positioning; radial & axial on tool holders #2 - #5; motorized feed beam adjustment with independent adjustment top head; top head with independent adjustment of chip breaker & pressure element. -- Universal spindle with 270° of movement.Feed System: -- Variable feed speed from 20 - 118 FPM, 7.5 HP inverter-controlled Cardan feed drive, overhead feed wheels with pneumatic pressure. -- Vertical tools with adjustable table plates to cutting circles, hardened infeed bed plates before & after 1st bottom head. -- Chromed tables and fences, (2) powered table rollers in bed and (1) between left and top spindles and (1) at outfeed. -- Infeed straightening table 2 M (6-1/2').Equipped with: -- Pedestal for machine controls separate from the electrical cabinet, central location of lubrication points. -- The safety hood, automatic table lubrication pump, and (2) lights inside the reinforced sound enclosure are electromagnetically interlocked, as is the phone modem..

WEINIG UNIMAT 818 S Feed Through Moulder 6-Head (B-R-L-T-T-B), working dimension 12-3/16" x 6- 5/16".Capacity: -- Working width 3/4" - 12-3/16" -- Working thickness 5/16" - 6-5/16" -- feed speed-variable with 10 HP inverter 20 - 200 FPM Head sequence: -- Bottom 25 HP, right 15 HP, left 15 HP, top 30 HP, top 30 HP, and bottom 30 HP motor; all motors with electronic spindle brakes. -- Spindle dia. 1-13/16" with cutter head speed of 6,000 RPM; -- outboard bearings on spindles #1, #4, #5 & #6. Electronic LED digital readouts for all spindlesJointer: -- Head # 1 Bottom straight jointer manual, remotely controllable with closed safety hood; Automatic stone adjustment; Maximum jointing width 12 -1/16"; With outboard bearing 4 3/4"; For tool circle 6 1/16"- 7-1/16" -- Head # 2 Right spindle Profile jointer automatic; For working height 4-3/4"; Remotely controllable with closed safety hood; Automatic stone adjustment -- Head # 3 Left spindle Profile jointer automatic; For working height 4-3/4"; Remotely controllable with closed safety hood; Automatic stone adjustment -- Head # 4 Top spindle straight jointer manual; remotely controllable with closed safety hood; Automatic stone adjustment; Maximum jointing width 12 1/16"; With outboard bearing 4-3/4"; For tool circle 6-1/16"- 7-1/16"Profile Jointer automatic; Remotely controllable with closed safety hood; Automatic stone adjustment; Maximum jointing width 9-1/16" without outboard bearing 4-3/4" -- Head # 5 Bottom spindle straight jointer manual; remotely controllable with closed safety hood; Automatic stone adjustment; Maximum jointing width 12-1/16"; With outboard bearing 4-3/4"; For tool circle 6 1/16"- 7-1/16"Profile Jointer automatic; Remotely controllable with closed safety hood; Automatic stone adjustment; Maximum jointing width 9-1/16" without outboard bearing 4-3/4" -- (4) Jointer cassettes for profile jointer, length 6" -- (2) Jointer cassettes for profile jointer, length 9" -- (1) Set of jointing stoneReadouts: -- Digiset (double mechanical readouts) for left and top radial adjustments. One readout is for the tool size and the other for the finished wood dimension (with Imperial inch adjustment -- Mechanical readouts on all other axes. Side pressure roller: -- (10) Driven feed roller shaft from above -- (5) Driven steel rollers in the machine table -- Axial setting range of the feed rollers opposite left spindle, 1-3/8" -- Extension of the feed shaft opposite the left spindle to 8 -1/4 in. -- Axial setting range of vertical spindle 3-1/8 in. Axial setting range of horizontal spindle 1 -3/4 in. (1st bottom 3/8 in.) -- All spindles diameter 1 -13/16" -- (6) Additional set of spacing collars, clamping length 6-11/16", diameter 1-13/16" -- Pressure shoe in front of 1st left spindle receding from tool, incl. lateral roller pressure, pneumatic -- Receding chip breaker in front of 1st top spindle, pneumatic. -- Pressure shoe in front of and guide after top spindle with mechanical digital displays

WEINIG PROFIMAT 23 Feed Through Moulder;(6)-Heads (B-R-L-T-T-B), working cap. 9-1/16" x 4-11/16".Specifications: -- Spindles 1-1/2" dia. with cutterhead speed of 6,000 RPM. -- Feed System & Features: variable feed speed from 20 - 78 FPM, powered by a 5.5 HP motor. -- Receding chip breaker at top spindles. Side pressure opposite right spindle; spring-loaded with (2) rollers; driven outfeed roller in bed. -- In-feed straightening table 2 M (78"), side pressure roller mounted to in-feed table. Note: Bare Machine: No dust manifold or tooling.

WEINIG PROFIMAT 23 Feed Through Moulder5-Head (B-R-L-T-B) Moulder with working cap. 9-1/16" x 4-11/16". -- Spindle sequence: Bottom 10 HP, right & left by 10 HP motor, top 15 HP, bottom 10 HP motor. -- Spindle diameter 1-1/2" with cutterhead speed of 6,000 RPM. All spindles equipped with mechanical digital readouts. Digi-set readouts on left and top spindles. Chipbreaker and pressure for left and top spindles with digital readouts. -- Feed: 4 HP Carden feed drive (chainless feed system), variable feed speed 18 - 78 FPM; (1) driven outfeed roller in bed. -- Equipped with: Infeed straightening table: 2 M (6-1/2') central lubrication system, central lubrication and full sound and safety enclosure. -- Extras: Includes manuals, used cutter-heads, many sets of assorted Knifes, and dust collection manifold. -- Machine is set up for 460V and it comes with a 230 V to 460 V step-up transformer -- Low hours, used for production of cabinet door rail and stiles components.

WEINIG - Rondamat 934, ...Profile Knife GrinderSpecifications: -- 9-3/8" Max. arbor length, 4" - 9" tool dia. -- 6" - 8-7/8" Grinding wheel dia., grinding wheel speed inverter controlled with grinding wheel speeds 1,500 to 3,000 RPM; 1.1 kW (1.5 HP) Motor.Equipped with: -- Hydro-clamping of grinding wheel to arbor. -- Tool carriage movement with precision linear table bearings; setting gauges for axial constant; axial (side) clearance angle 0° - 20°. -- Onboard diamond wheel dressing, 13-Gallon Coolant tank with 1.2 HP Pump.Dimensions: 50" x 43" x 62" HWeight: 1,600 Lbs