QUICK MACHINERY N-P50 Air Pod style Cold Press. -- Heavy Duty I-beam construction with machined steel plates for flat smooth pressing surface.Specifications: -- Platen pressing area size: 62" x 146" with side loading on 146" side (also available as end loading). -- 50 PSI Platen pressure over the entire surface area with 90 PSI supply air pressure. Pressure is applied by 12.8" dia. air pods with 5.9" stroke; (36) air pods total for this size press. -- (2) Pressure air pressure zones: 5' x 12' and 4' x 8'. -- Air powered raise and lower idler rollers in the bed of the press for loading & unloading panels; raising & lowering of idle conveyor roller tracks by control button on panel. -- Motorized Adjustable Daylight Opening from 2" to 40"; push button controls operate an electrically powered chain driven worm gear drive system for precise positioning of upper platen setting/opening. -- Controls: 60-Min cycle timers provide visual and audible signals at the end of each cycle and automatically releases platen air pressure at the end of each cycle if desired.

QUICK MACHINERY N-P50 Air Pod style Cold Press. -- Heavy Duty I-beam construction with machined steel plates for flat smooth pressing surface.Specifications: -- Platen pressing area size: 62" x 146" with side loading on 146" side. -- 50 PSI Platen pressure over the entire surface area with 93 PSI supply air pressure. Pressure is applied by 12.8" dia. air pods with 5.9" stroke; (36) air pods total for this size press. -- Air powered raise and lower idler rollers in the bed of the press for loading & unloading panels; raising & lowering of conveyor by control button on panel. -- Motorized Adjustable Daylight Opening from 2" to 40"; push button controls operate an electrically powered chain driven worm gear drive system for precise positioning of upper platen setting/opening. -- Controls: 60-Min cycle timers provide visual and audible signals at the end of each cycle and automatically releases platen air pressure at the end of each cycle if desired.Actual Model is a N-P50-05-12-SL-1PL-M-40-R-1Z.• Maximum platen pressure: 50 PSI at 93 PSI supply pressure• Lower platen dimensions: 5' x 12'• Side-loading design• Number of upper platens: 1• Upper platen dimensions: 5' x 12'• Vertical opening: Motorized adjustable from 2" to 40"• Lower platen roller tracks: Yes, non-powered roller tracks• Number of 12.8" diameter, 5.9" stroke air pods: 36• Number of air pressure zones: 1 (5' x 12' pressing)Optional powered roller tracks are available. -- The press model shown in pictures is a dual platen powered feed through end-load press.

QUICK L-HLPP-2-20-43-8-12 ...2-Sided Hydraulic Laminating Press: -- Number of working sections: (2) -- Working width, section #1: 6" and 8" -- Working width, section #2: 8", 10"; and 12" -- Maximum working length: 6,200mm (20.3') -- Maximum working height: 1,100mm (43.3") -- Pressure at the glue line: Up to 175 PSIMain Laminating Cylinders: -- Number of cylinders, section #1: (14) -- Number of cylinders, section #2: (21) -- Size of cylinders: 100 mm dia. x 80 mm strokeHolddown Cylinders: -- Number of cylinders, section #1: (14) -- Number of cylinders, section #2: (21) -- Size of cylinders: 40 mm dia. x 150 mm strokeLift Cylinders: -- Number of cylinders: (2) on each side = (4) -- Size of cylinders: 63 mm dia.Hydraulic Pump: -- Drive motor: 10 HP -- Maximum pressure: 140 kG/cm² -- Maximum Holddown Cylinder Pressure: 50 kG/cm² -- Maximum Side Lift Cylinder Pressure: 50 kG/cm² -- Shipped without hydraulic oil in the oil tank

QUICK MACHINERY N-P80 Air Pod style Cold Press -- Heavy Duty I-beam construction with machined steel plates for flat smooth pressing surface. -- Specifications: -- Platen pressing area size: 38" x 98"; with end loading on 37" side. -- 80 PSI Platen pressure over the entire surface area with 105 PSI supply air pressure. Pressure is applied by 12.8" dia. air pods with 5.9" stroke; -- Air powered raise and lower idler rollers in the bed of the press for loading & unloading panels; raising & lowering of conveyor by control button on panel. -- Motorized Adjustable Daylight Opening from 1" to 40"; push button controls operate an electrically powered chain driven worm gear drive system for precise positioning of upper platen setting/opening. -- Controls: 60-Min cycle timers provide visual and audible signals at the end of each cycle and automatically releases platen air pressure at the end of each cycle if desired. -- Single platen 38" X 98". -- Optional: powered roller tracksSpecifications:QUICK Laminating Pod PressN-P80-03-08-EL-1PL-M-40-R-1Z• Maximum platen pressure: 81 psi at 90 psi supply pressure• Lower platen dimensions: 3' x 8' (38" x 98")• End-loading or Side-loading: End-loading• Number of upper platens: 1• Upper platen(s) dimensions: 3' x 8' (38" x 98")• Vertical opening: Motorized adjustable from 2" to 40"• Lower platen roller tracks: Yes, Non-powered roller tracks• Number of 12.8" diameter, 5.9" stroke air pods: 24• Number of air pressure zones: 1 -- The press model shown in pictures is a dual platen powered feed through end-load press.

QUICK N-P50 Fixed Daylight Opening Air Pod PressThis Pod Press can produce a maximum 50 PSI platen pressure over the entire surface at 100 PSI supply air pressure. Press has a fixed vertical daylight opening of 44". The (18) 12.8" max. diameter air pods have 5.9" stroke.Material conveyance is via automatically extending and retracting (via pneumatic cylinders) non-powered roller tracks. A cycle timer provides visual and audible signals at the end of each cycle if desired, and also automatically releases platen air pressure at the end of each cycle, if desired.Specifications: -- Maximum platen pressure: 50 PSI at 100 PSI supply pressure. -- Lower platen dimensions: 4' x 8' -- End-loading or Side-loading: End-loading -- Number of upper platens: 1 -- Upper platen(s) dimensions: 4' x 8' -- Vertical opening: Fixed at 44" -- Lower platen Non-powered roller tracks. -- (18) 12.8" diameter, 5.9" stroke air pods. -- Number of air pressure zones: 1Lead Time: Approximately (12) weeks from time of order.Actual Model: N-P50-04-08-EL-1PL-F-44-R-1ZNOTE: Please let us know of any "Special or Specific" safety equipment requirements that you may have prior to order

QUICK MODEL L-HLPP-1-36-43-6 SINGLE SIDED HYDRAULIC LAMINATING PRESS FOR POSTS AND BEAMS: -- Number of working sections: 1 -- Maximum working length: 36'. The 36' length achieved by manufacturing the machines in two 18' long pieces; the two 18' pieces are then joined together, resulting in 36' total working length. -- Maximum working width: 43" -- Maximum working thickness: 6"Main Laminating Cylinders: -- Number of cylinders: (30) -- Size of cylinders: 80mm dia. x 80mm strokeHolddown Cylinders: -- Number of cylinders: (30) -- Size of cylinders: 40mm dia. x 150mm strokeSide Lift Cylinders: -- Number of cylinders: (2) per section = (4) -- Size of cylinders: 63mm dia.Hydraulics: -- Hydraulic pump drive motor: 7-1/2 HP -- Maximum pressure: 140kg/cm2 -- Maximum Holddown Cylinder Pressure: 50kg/cm2 -- Maximum Side Lift Cylinder Pressure: 50kg/cm2 -- NOTE: Shipped without hydraulic oil

QUICK MACHINERY N-P80 Air Pod style Cold Press. -- Heavy Duty I-beam construction with machined steel plates for flat smooth pressing surface.Specifications: -- Platen pressing area size: 49" x 97" with end loading on 49" side. -- 80 PSI Platen pressure over the entire surface area with 102 PSI supply air pressure. Pressure is applied by 12.8" dia. air pods with 5.9" stroke; (28) air pods total for this size press. -- Air powered raise and lower idler rollers in the bed of the press for loading & unloading panels; raising & lowering of conveyor by control button on panel. -- Motorized Adjustable Daylight Opening from 2" to 40"; push button controls operate an electrically powered chain driven worm gear drive system for precise positioning of upper platen setting/opening. -- Controls: 60-Min cycle timers provide visual and audible signals at the end of each cycle and automatically releases platen air pressure at the end of each cycle if desired. -- Single platen 49" X 97" . -- The press model shown in pictures is a dual platen powered feed through end load press. -- Actual model is N-P80-04-08-EL-1PL-M-40-R-1Z

QUICK Clamp Rack 8' -- Description: The QUICK Clamp Rack features a cleanly-designed, exceptionally strong frame, with massive 4" x 4" structural tubing cross beams and feet, and 4" x 6" structural tubing legs.The innovative “two-sided"; frame design allows for either one-sided or two-sided operation, at the shop owner’s discretion. The one-sided configuration allows for placement of the frame tightly against a wall, for maximum compactness. The two-sided configuration doubles the amount of easily-accessible clamping area, for industry-leading “room to work."; The Rack is configured by choosing either of the two available foot mounting positions. -- Specifications:96" Wide (36) Clamps 3.5" X 40" opening

QUICKWOOD CD2-300 Moulding & Profile Sander or Denibber;4-Head Brush Loading Sander, 12" width and 4" height cap., for 3-sided sanding & denibbing. Head Configuration: -- (2) "BH300" Overhead rotating abrasive/brush heads, both arbors equipped with a combination of abrasive and brush loadings, 12" long arbors, 12" max. dia. sanding discs. -- 0.75 HP Motor drives each arbor with inverter for 200 - 1,200 RPM arbor rotation speed. -- Right & Left ("BH-140" & "BH-100" respectively) side mounted rotating abrasive/brush heads. -- Tilting heads and adjustable in-and-out, 6" long arbor, 8" dia. sanding discs, 0.5 HP motor each head. -- 0" - 4" Max. manual part height adjustment via hand wheel; 57-1/2" long roller conveyor with PVC covered rollers, variable feed speed 10 - 60 FPM. -- Infeed & outfeed overhead holddown rolls and (1) between the top heads. Includes centralized control panel, hubs, abrasive, & brush. -- Can also be ordered with just (2) top heads or (3) heads, ie. Left or Right. Call for separate prices.

QUICKWOOD - RO 800-1, ...Denibbing Sander.1-Head with 32" max. cap., 0" - 4" max. part thickness opening. Equipped with: -- (1) Carousel head with: (4) Rotating arbors mounted on a central rotating drive assembly, carousel rotation 2 - 20 RPM, 0.75 HP rotation drive. -- Arbor/spindles are: 11.4" Long; 350 - 1,150 RPM spindle speed with LED readout on control panel; 2.5 HP main motor; each arbor holds a combination of (25) "Quick-Discs" & (12) nylon brush loadings of 13-3/4" max. dia. -- Feed system with: (2) 2-3/8" Wide narrow conveyor belts and side guides (to keep panels from moving side-to-side), motorized width adjustment in-and-out from the center. -- Manual thickness opening 0" to 4". -- Variable feed speed from 6 - 36 FPM, 0.75 HP feed drive. Complete with: -- Control panel and (2) 6" dia. dust collection ports.

QUINCY QSVB-25ANN2C Vacuum Pump:25 HP "QSVB Series", 371 CFM, 29.9"HgV rotary screw vacuum, positive lubrication fluid pump; 3″ inlet and 2″ exhaust port.. -- Equipped with:Modulating inlet valve, temperature regulating valve, and high discharge temperature shutdown system with manual reset. -- Complete with:Control panel, electrical enclosure, gauges, exhaust separation system, spin-on fluid filter, and magnetic motor starter. NOTE: The pump only has 969.2 total hours on the meter

QUINCY - QMT15 ACA, ...Air Compressor (Rotary Screw) w/DryerSpecifications: -- 15 HP - 54.9 CFM @ 125 PSIG; 120-Gallon tank mounted with Refrigerated Dryer & Filters. Equipped with: -- 15 HP TEFC Motor; air-cooled aftercooler; high efficiency inlet filter; upward package air discharge; vibration isolation; Wye-Delta start. -- 54.9 CFM @ 125 PSIG; 69 dBA; 120-gal horizontal tank; refrigerated air dryer.Total operating hours: (29,407).Specifications subject to verification

QUINDAO YICH - YICH-BC600, ...Automatic Feed Through Moulding Sprayer w/Drying Tunnel & 18" width cap. Machine setup: (2) C.A. TECHNOLOGIES AUTOCAT HVLP" low pressure Spray Guns and (1) GRACO "D54311" twin-diaphragm pump. This machine has only sprayed water for testing its operation and never used finishing spray materials.Conveyor belt: PU Abrasion resistant and chemically resistant material; conveyor driven by an electric motor and gear reduction box; overall construction: Cold roll steel plates, bent & joined for stable construction.Sprayer with: (3) Chambers are closely spaced and removable for cleaning; Guns are adjustable in height & angles to set the best angle for coverage; parts are guided into the machine by left/right roller guides. Specifications: -- Max. workpiece width: 600 mm (24") -- Min./max. part thickness: 10 - 120 mm (1/2" - 4-3/4") -- Min. part length: 600 mm (24") -- Feed speed: Adjustable, 15 - 100 FPM -- Number of spray guns: (6) -- Overall Dimensions - 3500 mm x 2100 mm x 2560 mm -- Weight 1000 kG (2,200 Lbs .. need to confirm)Electric powered IR oven with circulating airOven is a variable speed and variable temperature using a roller type conveyor. Current owner has used the oven at 200FOven Specifications: Min/Max part width ½" – 15 ½" Min/Max part thickness ½" – 5" Variable feed speed up to 50 FPM (14 MPM) Feed motor power 1.5 kW Fan power 1.1 kW Heating Power 10.8 kW Overall size 32’ × 38" x 67" H

RADER - Trailer Dumper with 30 ft. Tipping DeckComes with the following components and features: -- This unit was installed at the current location in approx. 1971 and is reportedly in great working order and condition. -- Previously used for Dumping Wood Chip Trailers. -- Professional rigging and loading is available. Decks are often extended for longer (53 ft.) trailers.

RAIMANN Model ASA 1650, Veneer Patcher.Specifications: -- 61" Throat cap., 3 HP gear motor with new/rebuilt drive unit, strip type mechanical plug-feeder mechanism - cap. of up to (40) plugs/Min.; -- Thickness of veneer patchable 1/32" - 1/5" (0.08 mm - 0.2 mm) (softwoods), 1/20" - 3/16" (hardwoods). P-34 dies. -- Tool sequence: Veneer patch is cut by the table die and scrap is ejected into discharge chutes, veneer patch blank is then positioned against the underside of the table die, plug punch cuts replacement veneer patch from underside and patch is inserted into the proper position. -- Reconditioned by experts. -- Overall size: 10' 8" (3,250 mm) Length x 67" (1,700 mm) height; approx. weight 12,000 Lbs (5,450 kG). -- Optional Glue applicator add ...$9,975. -- Optional strip feeder add ...$6,750.Actual model is RAIMANN Model ASA 1650

RAIMANN - KM-310, ...Gang (Multi-Blade) Rip Saw12-1/4" Max. width cap., 13-1/2" chain width, 50 HP - 4,200 RPM V-belt driven arbor.Features: -- "Quickfix Hydro-Quick" Arbor: Multiple Saw blades are mounted on the arbor, they slide up-and-down the arbor into position and lock into place by tightening the end of the arbor; no tools & no spacers required. -- Frequency controlled feed speed of 13 - 110 FPM, 2.2 HP feed drive, chain spikes every 3rd chain link, automatic chain lubrication.Specifications: -- 300 mm (11.8") Max. saw blade dia. with 80 mm (3.15") bore, 65 mm (2.55") dia. arbor. -- Provides 3" max. depth of cut with pressure shoe, 3-1/2" depth of cut without. -- Manual thickness adjustment of upper holddown rolls with indicator scale. -- 6" Throat depth to the right of blade; 7/8" min. strip width, 17-3/4" min. stock length.Equipped with: -- (4) Sets of top & bottom antikickback fingers. -- Extended infeed with additional bed roll, and adjustable infeed fence. -- Motor load meters and automatic STAR DELTA starting. -- Automatic over thickness shutoff on infeed and 7-1/4" dia. dust hood.

RAIMANN KR 310 2M Multiple Rip Saw System ( 2 Moving Blades )12-1/4" Max. width cap., 13-1/2" chain width, 50 HP - 4,200 RPM V-belt driven arbor.Equipped with:& Features -- Quick Fix arbor with: (2) Movable blade and (3) fixed blades; (4) Laser Lights. -- Enlarged movable saw housing with 25" pass through. Ball threaded adjustment of spindle. Saw blades mounted to individual collars. -- Chain with spikes every 3rd link, with automatic oiler with indicator light. -- Driven fluted lower roller with smooth upper roller for smooth feeding. Auto oiler fo guide lubrication. -- (4) Sets of anti-kickback fingers and 12" dia. dust hoods. Cutting Specifications -- Cutting depth with 12" Dia. saw blades, 2-1/2" with pressure shoe; 4" without pressure shoe. -- Variable feed speed, 16 - 158 FPM, feed drive 2 HP motor.Additional Features -- Sound enclosure with vertical pneumatic lifting -- Adjustable infeed fence. -- Automatic over thickness shutoff on infeed. -- Automatic starting and swing arbor mount for control panel.Note: Transformer for 600 volts included if necessary

SCM TECH Z1 CNC MACHINING CENTER (W/ATC/BORING/"C" AXIS): -- Specifications:Working Capacity:"X" axis 120" (3,050 mm), "Y" axis 41.3" (1,050 mm), "Z" axis stroke 5.9" (150 mm), max material thickness 3.9" (100 mm). -- Positioning speed: "X" & "Y" axis is 229 FPM (70 MPM), "Z" axis is 72 FPM (22 MPM).Axes positioning by AC Brushless motors and YASKAWA drives; all axes ride on prismatic guideways & sliding blocks. -- Worktable:(6) "TV" tube-less mobile support rails, (2) vacuum pods per rail; (4) pneumatic lifter rails for heavy panels; (6) pneumatic pop-up backstops, (6) pneumatic pop-up front stops; (2) pneumatic pop-up side stops.LED display positioning assistance for the support rails & vacuum pods; (2) independent working fields; -- Boring Head:3 HP (2.2 kW) motor, 4,000 RPM; (8) Independent vertical spindles, (5) spindles in "X" & (3) spindles in "Y".(6) Horizontal spindles (2+2) in "X" & (1+1 ) in "Y" axis; (1) "X" axis grooving saw for max. 120 mm dia blade - 6,000 RPM. -- Machining:(1) 10 HP (7.5 kW) Air-cooled Electro-spindle router with HSK F63 adaptor; variable speed from 1,000 - 24,000 RPM, max. torque achieved at 12,000 RPM; static inverter for stepless speed & rapid shutdown rotation.(1) NC controlled "C" Axis for 360° Horizontal Processing.(1) 10-Position ATC rack mounted on the RH side of the machine. Max. tool weight is 8 KG (17.6 Lbs). -- Operator & Machine Control:PC front end with SCM "Xilog Plus" + Windows "7" Pro operating system; 15" CRT color display, CELERON 2 GHz processor, enclosed in air-conditioned cabinet."XILOG PLUS" offers the advantage of having simple and intuitive software • Easy-to-use: easy planning of 3D elements due to the software modules: Cabinet to create complete cabinets and furniture; Nesting for rectangular and free-form elements it also ensures reduced production time and tool paths; WD to create complete fastenings; intuitive programming due the pre-set large graphics macro library; Immediate work table set-up from 3D graphics -- Complete with:(1) 100 M³/Hr Vacuum Pump; automatic lubrication system; "BUMP STOP" safety system; Scrap conveyor. -- Actual Model is SCM TECH Z1

SCM SANDYA 7 RCS Wide Belt Sander2-Head, 42" cap. - Great solid wood finish Sander. -- 1st Head: Grooved steel contact roll, 6-1/4" dia., 30 HP motor -- 2nd Head: Combination head, rubber covered contact roll, 6-1/4" dia. (65 Shore), and 2" wide finishing platen, 25 HP motor. -- 43" x 75" or 85" Abrasive belts with electronic tracking & pneumatic belt tensioning, pneumatic exclusion of all contact rolls. -- Conveyor belt feed with variable feed speed, 14.5 - 30 FPM, 1.5 HP motor, automatic part thickness adjustment, -- Motorized thickness opening with LED readout,0" - 6-1/4" via (4) precision conveyor bed jacks. -- Infeed & outfeed spring loaded rubber covered holddown rolls on all heads, -- Motor load meters, infeed and outfeed conveyor extensions, WYE-DELTA soft start.

SCMI OLIMPIC K 560TE EDGEBANDER (W/PRE-MILLING): -- Specifications: Edge Capacity: 0.4 to 6 mm (0.016 to 1/4") for strip feeding. -- Panel Capacity: Min. panel width: 60 mm (2.375"); min. panel length: 140 mm (5-1/2").Min./max. Panel thickness: 8 - 54 mm (0.375" - 2.125"); min. distance between panels: 600 mm (24").Equipped with: -- Pre-milling Station: (2) 2.0 HP (1.5 kW) motors; rectifies/cleans panels already sized. -- Adjustable Infeed Fence: Manually preset with digital indicator; pneumatic in/out positioning. -- Automatic Strip & Coil Feed Magazine: For straight edges and 3 mm guillotine for coils. -- Gluing Station: For EVA (Hot Melt) with: Quick change/disconnect Teflon glue pot for fast glue tanks change if needed; Heat up time approx. (10) Min. -- Pressure Section: Manual digital positioning; Teflon coated pneumatic driven roller & (2) spring loaded idle rollers.Workstations: -- End Trimming Station: (2) Front & rear 1/2 HP - 12,000 RPM motors mounted on THK guides; swivels 0° - 15° for straight & angle cutting. -- Top & Bottom Trimming Unit: (2) 0.7 HP - 12.000 RPM Motors; capable of tilting & pneumatic positioning for (3) settings, flush/bevel/radius trimming for quick setup. -- Top & Bottom Profile Scraping Unit with: Digital indicators; large dia. copy wheels for max. accuracy and pneumatic in/out positioning. -- Glue scraping Unit: Eliminates any excess glue. -- Buffing Unit: (2)Top/bottom 1/4 HP - 2,800 RPM motors; tilting up to 12°.Operator & Machine Control: -- "STARTOUCH" Controller with: 12" Touchscreen display; capable of storing (100) programs. -- Machine automation by PLC function and encoder positioned in the panel feed track pinion. -- Diagnostics for a quick solution to errors: Process statistics data (i.e., number of pieces/edges) and track feeding.Features & Complete with: -- 2-Speed feed speed of 40 & 60 FPM (12 & 18 MPM); (1) 2-1/2 HP feed drive motor. -- 200 Hz frequency inverter for all trimming units. -- Manual adjustable top hold-down pressure beam. -- Full sound enclosure cover and outboard panel support. -- Actual Model is: SCM OLIMPIC K 560TE