SANDMAN M7236 Downdraft Sanding Table110V 1 HP (M7236) T.E.F.C Motor with 15’ power cord. -- 72" x 36" Rubberized work surface. -- 10-5/8" LAU blower with sealed ball bearings. -- Industrial casters with 5" wheels, (2) ridged and (2) swivel-lock 2-ways. -- Hinged tilt-up top with gas strut lid support for easy filter servicing. -- Grid system top adds versatility. -- (18) Month warranty on parts.NOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.

SANI-TECH - SC1040/30, ...Auger Compactor -- Motor: 10 HP. -- Hopper capacity: 4.3 Cubic yards. -- Auger RPM: 10. -- Displacement rate: 270 Cubic Yards/Hour. -- 20-Yard Compactor

SAS SCORPION ENGINE PULLER Model SC40 DescriptionIncrease cash recovery from your recycling operationsSAS Forks Scorpion High Speed Motor Puller – Scrap Yard Engine Puller – Auto Recycling Engine Puller – Excellent for self service yards processing vehicles before crushing.Generate revenue:Process end of life vehicles in less than 60 seconds.Pull scrap engines and transmissions in 30 seconds.30% more revenue by separating metals from bodies.1000% more revenue per lb. on wire harness from engine compartment and dash.80% more visibility with a direct line of site from the operator’s window through the forks.Cycle time less than 15 seconds from park to full extension.Serviceable for long life. Replace blades in 3 hours or less.estimated only.Engineered & built for optimum performance:Engineered tough for continuous prying and durability.Hardened pins and bushings and grease-able pivot points for extended service life.Hydraulic hoses and cylinders are protected to minimize potential damage from sharp objects.Built with high strength blades and carriage skid plates for extended service.Clean up of ground debris is a snap with center plow blade.Speed is paramount in this design. Operator uses grapple from the cab, no torches, no personnel needed to hook up chains to pull or move engines. Safer, quicker and less costly removal of engines and transmissions.

Saturn Model 36x20 Slow-Speed Shredder --36" long x 20" wide chamber opening --1/2" knives. -- KYB MRH-30-SW2 hydraulic system powered by a 50-hp three-phase electric motor. --Comes equipped with stand and controls. -- Excellent for plastic, E-scrap, rubber, small tires, paper, cardboard, light metals.

SAVI HFK-250 Veneer Guillotine; General Specs: -- 102.4" (2,600 mm) Width cap., 4" daylight opening, hydraulically operated knife, 4 HP Leroy-Somer motor powers hydraulic unit with reservoir. -- Originally fitted with motorized parallel fence with 0.5 HP two speed gearmotor drive, push button operated, adjustable from 1" - 50" with magnified tape reader in front of machine. -- Equipped with: 2nd Cut feature with automatic reset, laser guide line light, photoelectric barrier guard for knife & hold-down beam, 2-hand operation of knife cycle. -- Note: Rear fence has been removed or modified. Shaft has chain/sprocket.

5 HP motor with 8" or 10" blade cap. -- Features: SawStop Safety System, blade stops and retracts on accidental contact, protection is always on, performs continuous self checks, invisible protection, does not interfere with work, compatible with all standard blades; works on all woods and non-conductive materials. -- Includes bypass switch for cutting metal. European style riving knife to minimize kickback; Low profile blade guard for narrow cuts; Quick-change mount for guard and riving knife ÷Large start/stop paddle for hands-free shut off; Main power switch with removable lock-out key; Magnetic contactor motor control; Blade shroud for improved dust collection; Zero-clearance insert; Extra heavy castings ÷Widely spaced trunnions; Infinitely adjustable trunnion assembly for precision alignment. -- Also includes: Vertical slide blade elevation for increased stability; Long-lasting V-ribbed belts; cast iron handwheels; Two access doors in cabinet; Powder-coated cabinet.

SAWSTOP - ICS 73230, ....Table Saw w/Safety "Stop Feature"Specifications: -- 10" Blade cap.; 7-1/2 HP motor; 3-1/8" depth of cut @ 0°; 2-1/4" depth of cut @ 45°; 13/16" max. dado width; 5/8" arbor dia. -- Features: -- Enclosed cabinet; Heavy-Duty belt drive; cast iron trunnions; SAWSTOPS's revolutionary flesh detecting safety mechanism. -- Includes: -- 52" "T-Glide" rip fence system; side support table and laminated top; 4" dust collection port; magnetic contractor motor control; main power switch with removable lock-out key. Actual model is: "ICS 73230"

SCHELLING FM-H 330/330 Automatic Panel Saw 129.9" (3,200 mm) Cutting length, 3.3" (85 mm) max. saw blade projection.Specifications & Features: -- 11 kW (15 HP) main & 1.6 kW (2 HP) scoring motor. -- Variable saw carriage travel speed from 0 - 262 FPM (80 MPM), constant return of 262 FPM (80 MPM). -- Electronically controlled overhead program fence with grippers, rack & pinion driven on both sides, forward speed from 0 - 262 FPM (80 MPM), return speed of 262 FPM (80 MPM); (6) Clamps open up to 3.9" (100 mm). -- 1,500 mm Long crosscut fence (front-to-back), (2) side/crosscut aligners for up to 87" crosscuts, (1) in front & (1) behind pressure beam. -- SCHELLING "COMPOSER" operating system; on-board SCHELLING optimizer, color monitor (displays cutting dimensions & patterns w/moving graphics), self-diagnostic, data input by keyboard & mouse or direct downloading from office PC is possible. Complete with: -- (3) Front mounted air float tables for moving panel from rip position to crosscut position; fully enclosed for safety with man-height sheet metal panels & wire screen windows.Specifications subject to verification.

SCHELLING FXH 430/410 FRONT LOAD, AUTOMATIC PANEL SAW: -- Specifications:169" (4,300 mm) Cutting length & 167" (4,250 mm) pull back; 3.9" (99 mm) max. saw blade projection, 23 HP (17 kW) main & 3.5 HP ((2.6 kW) scoring motor. -- Saw Carriage: Electronically controlled saw carriage with rack & pinion drive; variable travel speed 1 - 394 FPM (1 - 120 MPM), constant return of 394 FPM (120 MPM). -- Pusher Fence: Electronically controlled overhead pusher fence, rack & pinion driven on both sides; (9) Gripper clamps that open up to 3.5" (90 mm). -- Forward speed 0 - 262 FPM (0 - 80 MPM), return speed 262 (80 MPM) FPM; travel via brushless AC Servo Drive -- Operator & Machine Control:PC Front-end with Schelling "MCS" + Windows "NT" operating system.17" Color display with SVGA resolution (displays cutting dimensions & patterns w/moving graphics); virtually unlimited storage capacity, standard keyboard & mouse.Ethernet card; 128 MB Ram, 56K modem. Integrated graphical self-diagnostic, remote diagnostics by the factory is possible via dedicated phone line; data input by keyboard or possible direct downloading from office PC.SCHELLING "MCS" software displays simulation of patterns before actual cutting; graphical representations of cut-to-size parts in production shows the operator what to do in "real time". -- Complete with:2,300 mm Long crosscut fence (front-to-back), (2) automatic side/crosscut aligners for up to 87" (2,210 mm) crosscuts, (1) in front & (1) behind pressure beam cut line.(3) Front mounted air floatation tables, each table 24" x 83" (609 x 2,108 mm), rear of machine fully enclosed for safety with man-height safety fencing. -- Actual Model is SCHELLING FXH 430/410

SCHELLING FM-430/410 CNC Front Load Panel SawSpecifications & Features: 169" (4292 mm) Cutting length & 165.3" (4,200 mm) pull back, 3.75" (95 mm) max. saw blade projection; 25 HP (19 kW) 4,100 RPM main & 3.4 HP (2.5 kW) 5,600 RPM scoring motor. -- Equipped with: Variable saw carriage travel speed from 0 - 278.8 FPM (85 MPM), constant return of 278 FPM (85 MPM). -- Electronically controlled overhead program fence with rack & pinion driven on both sides; forward speed from 0 - 278 FPM (85 MPM), return speed of 278.8 FPM (85 MPM); equipped with (8) gripper clamps (open up to 5" (130 mm). -- Features: SCHELLING "COMPOSER" IBM-AT Compatible Computer Control; aftermarket color monitor (displays cutting dimensions and patterns w/moving graphics) , self-diagnostic, data input by keyboard; onboard optimization program. -- Complete with: 2-3/4" to 87" (2,200 mm) Long side/cross-cut aligning zone, (1) aligner in front & (1) behind the cut line. -- (3) Front mounted air float tables for moving panel from rip section to the cross-cut section, (2) movable and (1) fixed; each with their own blower. -- Rear of machine fully enclosed for safety with man-height sheet metal panels & wire screen windows. T

STEFF 2034/1 Power Feeder (3) 4-3/4" Dia. and 2-1/4" rubber feed rollers with 60-shore hardness. -- (2) Speeds are obtained by changing the position of the gears inside the housing while the other (2) aspeeds result from switching of the bipolar motor. -- 0.75 HP Motor with forward-and-reverse. -- (4) Feed speeds of 13 - 26 - 36 & 72 FPM. -- Feeder head movement in any position up throughout full 180° range. -- 20" Standard reach of head from base. -- Hardened steel drive gears. -- Electrostatic powder coated finish on all cast iron parts. -- Easy access external lubrication points for each roller shaft. -- Fully adjustable mounting column w/locking joints. -- Options: 2.5" or 3" wide feed rollers, conversion kit to belt feeder, different roller shore hardness and steel toothed rollers; please ask for prices.

STEFF 2034/3 (3) 4-3/4" Dia. and 2-1/8"wide rubber feed rollers with 60-shore hardness. -- 2-Speeds are obtained by changing the position of the gears inside the housing while the other 2-speeds result from switching of the bipolar motor. -- 1 HP motor with forward-and-reverse. -- (4) Feed speeds of 13 - 26 - 36 & 72 FPM. -- Feeder head movement in any position up to a full 180° range. -- 20" Standard reach of head from base. -- Hardened steel drive gears. -- Electrostatic powder coated finish on all cast parts. -- Easy access external lubrication points for each roller shaft. -- Fully adjustable mounting column w/ locking joints. -- Options: 2.5" or 3" wide feed rollers, conversion kit to belt feeder, different roller shore hardness and steel toothed rollers; please ask for prices. -- With (35) years of producing Power Feeders, STEFF has a huge market in the USA.Add $ 100 for 230 V, single phase option

STEFF 2038/1 Power Feeder (3) 4-3/4" Dia. and 2-3/8" rubber feed rollers with 60-shore hardness. -- 2-Speed - 0.75 HP motor with forward-and -reverse. -- (8) Feed speeds of 6 - 13 - 16 - 21 - 36 - 42 - 54 & 102 FPM. -- Feeder head movement in any position up to a full 180° range. -- 20" Standard reach of head from base. -- Hardened steel drive gears. -- Electrostatic powder coated finish on all cast parts. -- Easy access external lubrication points for each roller shaft. -- Fully adjustable mounting column w/locking joints. -- Options: Longer reach (34" & 38") from base to head; 2.5" or 3" wide feed rollers, conversion kit to belt feeder, different roller shore hardness and steel toothed rollers; please ask for prices.

STEFF 2038/3 Power Feeder. -- (3) 4-3/4" Dia. and 2-1/4" rubber feed rollers with 60-shore hardness. -- 2-Speed - 1 HP motor with forward-and-reverse. -- (8) Feed speeds of 6 - 13 - 16 - 21 - 36 - 42 - 54 & 102 FPM. -- Feeder head movement in any position up to a full 180° range. -- 20" Standard reach of head from base. -- Hardened steel drive gears. -- Electrostatic powder coated finish on all cast parts. -- Easy access external lubrication points for each roller shaft. -- Fully adjustable mounting column w/ locking joints. -- Options: Longer reach (34" & 38") from base to head; 2.5" or 3" wide feed rollers, conversion kit to make it a "belt" feeder, different roller shore hardness and steel toothed rollers; please ask for prices.

STEFF 2038CI/1 Power Feeder(3) Rollers with continuous belt. -- 2-Speed - 1 HP motor with forward-and-reverse. -- (8) Feed speeds of 6 - 13 - 16 - 21 - 36 - 42 - 54 & 102 FPM. -- Feeder head movement in any position up to a full 180° range. -- 20" Standard reach of head from base. -- Hardened steel drive gears. -- Electrostatic powder coated finish on all cast parts. -- Easy access external lubrication points for each roller shaft. -- Fully adjustable mounting column w/locking joints. -- Options: Longer reach (34" & 38") from base to head; 2.5" or 3" wide feed rollers, conversion kit to belt feeder, different roller shore hardness and steel toothed rollers; please ask for prices.

(3) Rollers with continuous belt. -- 2-Speed - 1 HP motor with forward-and-reverse. -- (8) Feed speeds of 6-13, 16-21, 36-42, 54-102 FPM. -- Feeder head movement in any position up to a full 180° range. -- 20" Standard reach of head from base. -- Hardened steel drive gears. -- Electrostatic powder coated finish on all cast parts. -- Easy access external lubrication points for each roller shaft. -- Fully adjustable mounting column w/locking joints. -- Options: Longer reach (34" & 38") from base to head; 2.5" or 3" wide feed rollers, conversion kit to belt feeder, different roller shore hardness and steel toothed rollers; please ask for prices.

STEFF 2044/1 Power Feeder(4) 4-3/4" Dia. and 2-1/4" wide rubber feed rollers with 60-shore hardness. -- 2-Speed - 0.75 HP motor with forward-and-reverse. -- (4) Feed speeds of 13 - 26 - 36 & 72 FPM. -- Feeder head movement in any position up to a full 180° range. -- 20" Standard reach of head from base. -- Hardened steel drive gears. -- Electrostatic powder coated finish on all cast parts. -- Easy access external lubrication points for each roller shaft. -- Fully adjustable mounting column w/ locking joints. -- Options: Longer reach (34" & 38") from base to head; 2.5" or 3" wide feed rollers, different roller shore hardness and steel toothed rollers; please ask for prices.

STEFF 2044-3 Power Feeder. -- (4) 4-3/4" Dia. and 2-1/4" wide rubber feed rollers with 60-shore hardness. -- 1 HP - 2-Speed motor with forward-and-reverse. -- (4) Speeds (motor & gear) of 13 - 26 - 36 & 72 FPM. -- Feeder head rotates to any position up to a full 180°range. -- 28" Standard reach of head from base. -- Hardened steel drive gears. -- Electrostatic powder coated finish on all cast parts. -- Easy access external lubrication points for each roller shaft. -- Fully adjustable mounting column with locking joints. -- Options: Longer reach (34" & 38") from base to head; 2.5" or 3" wide feed rollers, conversion kit to belt feeder, different roller shore hardness and steel toothed rollers; please ask for prices.

STEFF 2048/1 Power Feeder(4) 4-3/4" Dia. and 2-1/4" rubber feed rollers with 60-shore hardness. -- 2-Speed - 0.75 HP motor with forward-and-reverse. -- (8) Feed speeds of 6 - 13 - 16 - 21 - 36 - 42 - 54 and 102 FPM. -- Feeder head movement in any position up to a full 180° range. -- 20" Standard reach of head from base. -- Hardened steel drive gears. -- Electrostatic powder coated finish on all cast parts. -- Easy access external lubrication points for each roller shaft. -- Fully adjustable mounting column w/locking joints. -- Options: Longer reach (34" & 38") from base to head; 2.5" or 3" wide feed rollers, conversion kit to belt feeder, different roller shore hardness and steel toothed rollers; ...please ask for prices.

STEFF 2048/3 Power Feeder (4) 4-3/4" Dia. and 2-1/4" rubber feed rollers with 60-shore hardness. -- 2-Speed - 1 HP motor with forward-and-reverse. -- (8) Feed speeds of 6 - 13 - 16 - 21 - 36 - 42 - 54 and 102 FPM. -- Feeder head movement in any position up to a full 180° range. -- 20" Standard reach of head from base. -- Hardened steel drive gears. -- Electrostatic powder coated finish on all cast parts. -- Easy access external lubrication points for each roller shaft. -- Fully adjustable mounting column w/locking joints. -- Options: Longer reach (34" & 38") from base to head; 2.5" or 3" wide feed rollers, conversion kit to belt feeder, different roller shore hardness and steel toothed rollers; ...please ask for prices.Add $ 100 for 230 V single phase option