CHAMPION - HRA25-25, ...Dual Stage Air Compressor. 25 HP Commercial Duty motor; 90.1 CFM at 175 PSI and 250-gal. horizontal tank. -- Features: CHAMPION's "R" Series 2-stage cast iron pump, dome pistons, and disc valves allow for higher performance at lower RPM's; largest roller bearings in the industry. -- The 250-gal. horizontal tank is equipped with: Large pressure gauge, standard tank drain, and a hard painted finish for years of durability. -- Complete with: Large dia. air filters, OSHA approved belt guard. -- Air-cooled aftercooler.

COMPLETE CHANTLAND 4234 Loose Bagging System4234 BELT-WEIGH BAGGER Including the following: -- Load Cell Weighing with "5511" Weighmeter Controller -- Color Touch Screen 5.4" size -- Single or Dual Set Point -- Calibration Routine -- Zero Tracking - Weigh Track -- Multiple Product Set-Up w/Quick Change over- (100) products -- RS-232, RS 422 Ethernet TCP/IP Connection -- NEMA 4X Poly Enclosure 16" x 14" -- Three Level Password Protection -- Requires Dedicated 120V /60 Cycles service -- Two Stage Variable Speed Control for Bulk Feed & Dribble Cut off by Weight Using VFD -- Flapper Style product Stop Gate for Positive Product Cut-Off -- Discharge Dust Collection Chute -- Spiked Agitator Above Inlet, with Drive, -- An Agitator Stirs the Product and Helps Deliver Product to the Belt. -- Surge Bin, Mounts to Flange of Packer, with Removable Lid, Inlet Flange and Dust Flange in Lid -- Approximately 10 Cubic Foot Capacity with Threated Ports for Customer Supplied Bin Level IndicatorsAP100 Automatic Bag Placer -- Bag Face 13-19 Inches -- Bag Length 24 Inches and up to 40 Inches Long -- Material of Bag Construction; Kraft Paper, Poly Plastic, Woven -- Gusseted Bags 5-1/2" Wide Gussets -- Upgrade to VEE Spout Clamp for AP10000FISCHBEIN "400NS" PLAIN SEWN CLOSURE SYSTEM -- This heavy-duty, state-of-the-art plain sewing system is designed for semi or fully automated bagging operations. -- The 400NS is specifically made for medium to high volume bagging applications that will require operating speeds up to 55 linear feet per minute @ 2.5 stitches per inch. -- This versatile unit will securely sew close woven polypropylene, multi-wall paper, and jute bags. -- Includes an infeed and standard unit is Right to Left travel.Standard features include: -- Empress model "100" two thread sewing head @ 2.5 stitches/inch -- Adjustable height high speed pedestal with casters. (31-56 inches) D4380 15" infeed -- Air thread pusher -- PLC controlled pneumatic actuators -- 24 VAC control circuit / 24 VDC solenoid valve controls,1HP, 1750 rpm motor 230 VAC single phase, or 230/380/460/575 VAC 3 PH -- NEMA 12 Electrical Components -- 180 Days System WarrantyNOTE: Minimum 6" of bag free top required

CHEN SAN FUNG SD-100 Denibbing Sander --39" Width cap.; (1) head with (6) 0.5 HP counter rotating arbors mounted on a central rotating drive assembly with (20) blades per spindle, variable assembly rotation from 2 - 20 RPM. -- Each arbor/spindle is equipped with abrasive fladder disc type brush media, variable arbor speed from 300 - 1,200 RPM. -- Conveyor belt feed with vacuum holdown, variable feed speed from 6 to 39 FPM with 2 HP drive. -- Infeed & outfeed holddown pinch rolls, 0" to 4" motorized part thickness with working width from 6" to 39" part size opening with mechanical readout. -- Complete with: Controls on belt loading side, RPM readouts for spindle speed, magnetic starters, 7" dust collection outlet and optional 15 HP vacuum turbine motor.

--In Auction: https://exfactoryauctions.com/Detail/SA-231009/event/A122024$1 --No RESERVE!-- CHIA LUNG KR-30 2-Spindle Dual Table Automatic Rotary Copy Shaper Equipped with: (2) 19” Dia. x 35-1/2” H Tables. (2) 6-1/4” Dia. Center clamp plates.

CLARK C20sC FORKLIFT - Cushion Tire, LPG Powered with compact chassis.Specifications: -- Basic Capacity at 24" load center, 4,000 Lbs -- Mast-Triplex Panoramic, Max. lift height 188", Collapsed Height 83" -- Full Free lift 59", Fork length 48", Chassis width 35", Overhead guard 81.1", Length to fork face 85.1", Carriage 33" Class II, propane fuel systemEquipped with: -- Side shifter with internal hosing -- Tires, Cushion Lugged Drive/Smooth Steer -- Power steering -- High capacity cooling system -- Electronic back-up alarm

CML NEW FINISHING TOWER/6 Multi Level Oven System: This type of oven is very flexible thanks to the FIFO (First In / First Out) operation and the possibility to adjust the stay time using more or less belt trays.It is particularly suitable to help the evaporation of the volatile components contained in UV curable paints, or to carry out a first degree of drying of conventional paints in an 'out of dust' environment. - Its technical characteristics also make this system extremely suitable for drying or curing materialDescription of the Standard Equipment & Specifications: -- Overall dimensions: 7,650 x 3,300 mm x 3,250 mm height (25’ x 11’ x 10.67’ H). -- Weight: 4.000 kG (8,819 Lbs)Multiple Floors Dryer, mod. TOWER/6 Paint Coated parts (panels components) are transported on (6) belt conveyor trays, moving vertically up/down, having a length of 6,500 mm (256") each. This practical length makes it possible to load "two panels charges" having a length of 3,000 mm. (9.85 feet) each. -- Max. weight supported by every belt tray level: 115 kG (253.5 Lbs). -- Max. allowed thickness 50 mm (1.97 inches) -- Speed controlled by inverter at belt travel steps of 3.250 mm (127.9") or in continuous model. -- Vertical movement on (4) pre-tensioned chains controlled by motor with gearbox. -- Cabinet made of structural carbon steel profiles and pre-painted insulated panels, complete with entry door and windows. -- Ventilation by means of laminar air distribution among the floors. Average air speed 2 m/Sec (6.56 feet/Sec) - (100% of the air volume is taken from the outside and exhausted to the outside). -- Air supply unit complete with centrifugal fan taking the air from the outside of the building, complete with heat exchanger to be supplied with hot water, with temperature adjustment system and double set of pocket filters. -- Air ductworks between air supply and exhaust fans and distribution boxes (plenum) is included. -- Ready to be connected to emergency system to stop the line -- Curing Tunnel operating functions controlled by SCHNEIDER PLC via electronic keypad input. -- Separate electrical cabinet in IP 55 execution - IP 55 motors -- Manufactured according to CE Standards and covered by a (12) Months or 2,000 Operating Hours Warranty for defective parts or materialOther Dims, Operation & Utilities: -- Dimensions of the electrical switchboard: 800 x 600 x 2,000 mm (2.7’ x 1,97’ x 6,56’) -- Total power: kW 10,5 -- Compressed air:: lt/Min 20 (5.29 gal/Min) -- Exhausted air volume: m³/Hr 7.500 (264,860 feet³/Hr) -- Supply air volume: m³/Hr 7.500 (264,860 feet³/Hr) -- Thermal power: Kcal/h 125.000 (326,000 BTU/Hr), - AIR In/Out: 50°C (122°F)

CMS NC-P.F./112-TUCU 5' x 12' 5-Axis CNC Router, with ATCSpecifications: -- Travels: X-Axis (Side-to-side) 3,600 mm (141.73"), Y-Axis (Front-to-back) 1,600 mm (62.99"), Z-Axis (Up-and-down) 700 mm (27.56"), 4th Axis (Around Z-Axis) 360° Continuous, & 5th Axis (Head inclination) +/- 100°. -- Distance between housings 155". -- Feed speeds: X-Axis 0 - 54,000 mm/Min. (0 - 2,125.98 IPM), Y-Axis 0 - 45,000 mm/Min. (0 - 1,771.65 IPM), & Z-Axis 0 - 10,000 mm/Min. (0 - 393.70 IPM). -- Positioning speeds: X-Axis 54,000 mm/Min. (2,125.98 IPM), Y-Axis 45,000 mm/Min. (1,771.65 IPM), & Z-Axis 10,000 mm/Min. (393.70 IPM).Equipped with: -- (2) 1,830 LR x 1,560 mm FB (72.05" LR x 61.42" FB) Moving tables, with Independent or synchronized movement, LIGNOSTONE surface, & Ground & tempered interchangeable slideways. -- CMS "TUCU" Universal 5th Axis head, with 8 kW (10-3/4 HP) - 18,000 RPM - 600 Hz ISO 30 Air-cooled electrospindle, with Variable spindle speeds 0 - 18,000 RPM, Max. Tool Length & Dia. 110 mm (4.33"). Electronic brake, Reverse, & BERGES "ACI 22" 22 kW (30 HP) Frequency static converter. -- 12-Position Automatic tool changer.Features: -- X, Y, & Z-Axes Carriages, with Ground & hardened sideways via 4-Point hitch (Recirculating, linear, & self-cleaning) bearing (Star-type), & AC Servo motors with Precision dual lead ball screws, Z-Axis with Automatic insert brake. -- Pneumatic compensating cylinders. -- Automatic centralized pressure-injected lubrication.Operator Control: -- ALLEN-BRADLEY/OSAI "86S0 MC" CNC Control, with 9" Color CRT, Color graphic visualization & tool path process simulation, Spiral interpolation, Parameteric functions, Tool radius & length compensation, Brief description of tool path for simple generation of part programs, Teach-in function, Double push button control, & PC.Complete with: -- Documentation. -- EATA "CRIA 2.5 EU3 VE" 15 L (3.96 Gallon) Cap. Chiller. -- BECKER 3 kW (4 HP) Vacuum Pump. -- Spare Spindle. -- Toolholders.NOTE: Machine currently not operational due to control/drive issues.Machine Dimensions: 202" x 140" x 138" H.Control Dimensions: 26" x 24" x 57" H.Control/Electrical Cabinet Dimensions: 40" x 36" x 96"; H.Chiller Dimensions: 24" x 19" x 39" H.Vacuum Pump Dimensions: 36" x 26" x 43" H.

CNC FACTORY PYTHON XPR FLAT TABLE MACHINE (W/LOADING, UNLOADING): -- Specifications:5' x 10' Single Table machine: stationary phenolic table is machined with a square "MATRIX" grid pattern for fixturing parts, -- Working field:"X" axis 122" (3,099 mm), “Y"; axis 62"; (1,575 mm) , "Z" axis stroke is 12" (305 mm). -- Positioning speed:"X" & "Y" axis 233 FPM (71 MPM), "Z" axis 82 FPM (25 MPM);Closed loop AC Servo drive system driving precision helical rack & pinion in "X" & "Y" axis & ground ball screw in "Z" axis;All axes ride on extra large precision profile linear guide ways. -- Work Table:"MATRIX" grid pattern allows use of vacuum pods or closed cell rope gasketing material and use of spoil boards for "nested based machining".Pneumatic Pop-Up Pins for manual and automatic material placement. -- Machining:(1) 12 HP (9 kW) "HSD" Electro spindle with ISO 30 adaptor, spindle speeds from 1,000 - 24,000 RPM;(1) 12-position ATC tool plate mounted on the head for "on the fly" ATC. -- Operator & Machine Control:"SYNTEC 4E 21"; graphic industrial control center with hand held controller.Built-in continuous operation file saving and production override with speed control G-Code compatible with virtual every Cad and software including USB and Ethernet file control.Acceleration and deceleration working and repositioning; Tool wear history with built-in alarm stops, work coordinates and on screen programming19" High resolution monitor; Ergonomic industrial keyboard & mouse; USB drive; serial ports for RS-232; all housed in a separate dust free cabinet -- Complete with:(1) 250 m³/Hr vacuum pump; auto tool length measuring sensor; . -- Options Include:(1) NC controlled "Robotic" in-feed scissor-lift loading table; (1) Rake system; (1) NC controlled & powered belt out-feed table with vacuum sweeping system. -- Actual Model is CNC FACTORY PYTHON XPR 510.

CNC FACTORY PYTHON XPR FLAT TABLE MACHINE (W/ATC): -- Specifications:4' x 8' Flat Table "Bridge Gantry" machine with: "Phenolic "MATRIX" grooved flat table for "NESTED BASE MANUFACTURING". -- Working capacity:"X" Axis 97" (2,464 mm); "Y" axis 49" (1,245 mm); "Z" axis stroke is 20.2" (515 mm); max. material thickness 10" (250 mm). -- Positioning Speed:"X" & "Y" Axis 279 FPM (85 MPM); "Z" axis 115 FPM (35 MPM).All axes movement is with 5G driverless Servo System with direct helical rack & pinion & 5G no homing calibration. -- Work Area:Flat table design with: "Matrix" grid phenolic surface for "Nested Base Manufacturing".The machine has: (6) Independent working zones with dual layer high flow vacuum; 2-left origins, 2-right origins, 1-front origin & 1-rear origin.Auto-material alignment pins, auto-unloading arm, material loading wheels; rear & side material alignment pushers. Automatic on/off vacuum flow, vacuum hold-down communication, automatic parts hold down, and release.Robotic Material Sensing Dust Hood; Single and dual vacuum ports. -- Machining:(1) 12 HP (8.9 kW) Air-cooled "HSD Electro-Spindle" with: ISO 30 adaptor, RH & LH rotation; variable speed from 1,000 - 24,000 RPM.(1) Rapid Fire 12-position revolving tool changer for "on the fly "ATC". -- Operator & Machine Control:"SYNTEC" PC Front End with: CNC Factory 5G, 5th generation CNC control + At machine cabinet and cutting software. Handheld MPG remote control with individual axis & real time simulation control; CNC speed control overrides & compensation at machine virtual support, HD digital monitoring camera, Wi-Fi, and Ethernet ready.Air-Conditioned control cabinet, 21" "TOUCH SCREEN" monitor; All mounted on a mobile cart. -- Complete with:(1) 150 cbm (60 Hz) Vacuum Pump; automatic pressurized Lubrication System for linear guides, pads and recirculating ball screw. Auto tool length measurement probe. Perimeter Safety System & fencing. -- Actual Model is: CNC FACTORY PYTHON XPR CNC

COE 249D Veneer Lathe with the following: -- 27" maximum log diameter, Approx.110" knife length. -- 1484 Veneer Lathe Big Bar. -- 1390 Veneer Lathe Core drive. -- 3 to 1 inner drive ratio. -- Capable of peeling approx. 35 cubic meters per hour. -- Includes: • Linden step feeder• Small log offset x-y spindle chucks• 27"; maximum log diameter• 1484 big bar• 3 to 1 inner drive ratio• Digital ball feed carriage drive -- Note: Sold without 'charger or drive' included. -- This COE Veneer lathe line was completely rebuilt and installed in 2006. The lathe was operated less than one year and is reportedly in very good condition.

COE 233 Rotary Veneer Lathe. -- 30" Swing and 44" Knife length., -- Turning motor LINCOLN 50 HP 230/460 -- Complete with: Hydraulic unit, all drive motors and controls. -- Includes: veneer knife. - Ideal for peeling short blocks.

144L X 120"D X 144"H (25) Filter Screens (4) 12" X 48", (4) 4-tube light panels(1) Exhaust Fan 1HP 120V

COMEC - LON-LS, ...Horizontal Belt SanderSpecial design for sanding of straight or curved solid wood parts such as: Chair legs, chair backs and other similar & difficult-to-sand parts.10 HP Belt driven motor; 12" dia. contact drum for 10" wide x approx. 140" long abrasive belt; air tracking & belt tensioning. -- Stock is fed over the contact drum with an overhead variable speed, pneumatically tensioned feed wheel. -- Sander belt power: 6.6 kW (9 HP approx.) - 220/440 V, 60-Cy, 3-Ph motor.

COMEC - FAS/2, ...Corner Milling MachineCOMEC FAS is a dedicated milling machine with: Inclinable heads for machining the corner of chair seats. Specifications: -- (2) Heads with: 5.5 HP motor and 40 mm spindle shaft. -- Max. cutter size: 150 mm (5.9"). -- Tilting of milling units: 20°/ +45° in horizontal plane. -- Fixed left hand column to support head unit. -- Max. working height: 200 mm (7.8").

COMEVA - CUBE 3, ...Edgebander (Single Phase)The CUBE 3 from COMEVA is designed to be a very compact "every day" Edgebander. The CUBE 3 Edgebander is operated through a PLC control system with a touchscreen. The machine handles panel thicknesses of 0.315" up to 1.77" (8 mm to 45 mm), The coil feed accepts Edgebanding from 0.4 mm to 2 mm thick; strip material can be hand-fed.Equipped with: -- Heated infeed fence for optimum glue penetration. Large capacity Teflon coated glue pot (2.64 Lbs). -- Single motor End Trimming station -- Top & Bottom Trimming -- Top and bottom Buffing. -- Feed speed is variable between 9.8 & 23 FPM (3 - 7 MPM); feed chain pads with replaceable rubberized surface inserts. -- Rubberized holddown rollers with ball bearings for low friction and long life. Work stations: -- Pneumatically operated guillotine for up to 2 mm thick banding, followed by spring loaded double pressure rollers. -- Single front/rear trimming unit, 0.3 HP motor. -- Top & Bottom trimming units, (2) 0.5 HP motors. -- Top & Bottom buffing station, (2) 0.16 HP motors. -- Complete with: Safety enclosure protects the operator from noise and debris. Engineered & Manufactured by COMEVA S.L, in Spain.Includes: Owner’s Manual with mechanical & electrical schematics and parts breakdown; covered by a 1-Year Factory Warranty on parts.

COMEVA C-400 B Programmable European Door Milling Machine: Specifications: -- Maximum door length, X-Axis 96" (2,440 mm). Maximum machining length from center to center of the farthest slots is 74.8" (1900 mm) based on a 120 mm hinge length. -- Working field Y-Axis 23.6" - 39.3" (600- 1,000 mm) min/max door width. -- Working field "Z" axis 1.18" - 2.36" (30 - 60 mm) min/max door thickness. Positioning: -- NC Controlled working table for X-, Y- & Z-axis part positioning & processing. X- Y- & Z- Axis movement via hardened round ways & ground ball screws.Work Table: -- (2) NC Controlled extruded aluminum support rails with (6) Non-Marking manually positioned pneumatic panel clamps. -- (1) NC Controlled extruded aluminum support table for "Hinge Plate" router spindles. Machining: -- (4) Manually adjusted 0.5 HP (0.37 kW), 12,000 RPM air-cooled "Hinge Plate" router spindles with ERC 32 collets, RH rotation. -- (1) NC Controlled 3 HP (2.2 kW) air-cooled 12,000 RPM horizontal "Case Lock" router spindles with ERC 32 collets, RH rotation. -- (2) NC Controlled 2 HP (1.5 kW) air-cooled 12,000 RPM vertical "Hardware" router spindles with ERC 32 collets, RH rotation.Operator & Machine Control: -- Separate control console with "ADTECH CNC 4640" Controller with numerical and function keyboard; -- Monitor displays programming graphics, machine data & subroutines, runs production programs while programming and editing -- Programming storage for 30 individual programs. -- Includes: Owner’s Manual with mechanical & electrical schematics. -- Engineered & Manufactured by COMEVA S.L, in Spain.

COMEVA - NICRON 2C, ...CNC Door Machining Center with ATC and Flat Table for NestingSimple, robust, fast, and versatile CNC that can meet all your needs milling, drilling, trimming etc. passage and entry doors. Using available CAD software, it can also machine any designs such as raised panels on entry doors or special bevels on door jambs. - Equipped with a Flat Table compatible with nesting, Router milling motor, Double-End horizontal milling motor to work on edges of all types of doors is added to "free space" location. Also (see options below) for machining the hinges on door jambsMachine Specifications. Head Composition: -- Milling Router with Tool Changer capability, working in conjunction with the 6-position tool rack. This Router can machine the door knob/plate openings, rebate on edge of door frame. -- (1) Double-End horizontal Router Head: The Double-End spindle has one of the outputs with a cutter for machining the hinges and the second output has cutter for milling of the door latch opening.Worktable: -- REXILON Nesting type flat table slotted for vacuum distribution and with (12) pneumatic reference stops. -- Tool changer with 6-position tool rack on one side of table. -- (4) Independent vacuum zones; Working area is 2,600 x 1,300 x 200 mm (102" x 51" x 7.8"). -- Workholding can be achieved with zoned vacuum table (for milling on the top surface of doors and wider door jambs, raised vacuum cups for edge of doors and machining of hinges on door jambs (with optional jamb fixture device below).Control & Software: -- Mobile CNC control panel for all axes control c/w display, keyboard, and mouse. -- Powerful CNC Controller for machining control on all axes, reference stops, vacuum zones, and working groups; -- CADCAM Software is UCAMAM V11 (standard version) with: Postprocessor (which translates to language of machine) drawings from images such as BMP, JPG, TIF, GIF, PNG, as well as vector files from any format ADOBE Illustrator, DXF (CAD), EPS, PLT, TXT. Draw with this software directly and has auto-nesting to optimize use of the material.Drives & Speeds: -- ATC Router is 9 kW, 12,000 - 18,000 RPM with DELTA Inverter. -- Horizontal double-end unit is: 2.2 kW, 12,000 RPM. -- X & Y-Axe Speeds are: 10 MPM (30 MPM with safety barrier, faster speeds available); Z-Axis is 10 MPM. Other Machine Composition. -- Piston Stops: (12) Divided into (4) fields. -- Lineal Guides: H/Win 20 mm wide. -- Lubrication System: Central - manual. -- Vacuum Pump: 160 CBM/Hr, 7.5 HP. -- Standard machine voltage: 220 V, 50 - 60 Hz, 3-Ph (Transformers available). -- Overall Dimensions & Weight: 3,900 x 2,150 x 2,100 mm (154" x 85" x 83"); Weight: 2,300 kG (5,000 Lbs).Optional: - CE regulation (Light barrier and perimeter fencing ): ....................3,100 Euro- Raised (50 mm) Vacuum Cups. Recommend (8) @ 165 Euro......1

COMEVA - C-250, ...Programmable Door Milling Machine Specifications: -- Working field "X-axis" 90.55" (2,300 mm) max. door length. -- Working field "Y-axis" 23.6" - 39.3" (600 - 1,000 mm) min/max. door width. -- Working field "Z-axis" 1.18" - 2.36" (30 - 60 mm) min/max. door thickness. -- Positioning:NC Controlled working table for "X", "Y", and "Z" part positioning & processing."X", "Y", and "Z" Axis movement via hardened round ways & ground ball screws. -- Worktables:(2) NC Controlled extruded aluminum support rails with: (4) Non-marking manually positioned pneumatic panel clamps.(1) NC Controlled extruded aluminum support table for "Hinge Plate" router spindles -- Machining: (4) NC Controlled 0.5 HP (0.37 kW), 12,000 RPM air cooled "Hinge Plate" router spindles with: ERC 32 Collets & manual spacing adjustment, RH rotation.(1) NC Controlled 3 HP (2.2 kW) air-cooled 12,000 RPM horizontal "Case Lock" router spindles with ERC 32 collets, RH rotation.(1) NC Controlled 2 HP (1.5 kW) air-cooled 12,000 RPM vertical "Hardware" router spindles with ERC 32 collets, RH rotation. -- Operator & Machine Control: Separate control console with: "DELTA" 12" TFT touch screen control with numerical and function keyboard;Monitor displays programming graphics, machine data & subroutines, runs production programs while programming, and editing.Programming storage for (30) individual programs. -- Complete with: 1-Year Mfg. Warranty, User's operator/maintenance manuals & backup disks. -- Available Options at additional cost:Additional 0.5 HP (0.37 kW), 12,000 RPM air-cooled "Hinge Plate" router spindles with ERC 32 collets = $ 1,976.00 each.Additional 2 HP (1.5 kW) air-cooled 12,000 RPM vertical "Hardware" router spindles with ERC 32 collets = $ 3,240.00 each.Actual Model is COMEVA - C-250, ...CNC DOOR MILLING MACHINEIncludes: Owner’s Manual with mechanical & electrical schematics and parts breakdown; covered by a 1-Year Factory Warranty on parts.

COMEVA - C-400 B Programmable, ...European Door Milling Machine: Specifications: -- Max. door length X-Axis 96" (2,440 mm); max. machining length from center-to-center of the farthest slots is 74.8" (1,900 mm) based on a 120 mm hinge length. -- Working field Y-Axis 23.6" - 39.3" (600 - 1,000 mm) min/max. door width. -- Working field "Z-axis" 1.18" - 2.36" (30 - 60 mm) min/max. door thickness. Positioning: -- NC Controlled working table for X-, Y- & Z-axis part positioning & processing; X- Y- & Z-Axis movement via hardened round ways & ground ball screws.Worktable: -- (2) NC Controlled extruded aluminum support rails with (6) Non-Marking manually positioned pneumatic panel clamps. -- (1) NC Controlled extruded aluminum support table for "Hinge Plate" router spindles. Machining: -- (4) Manually adjusted 0.5 HP (0.37 kW), 12,000 RPM air cooled "Hinge Plate" router spindles with ERC 32 collets, RH rotation. -- (1) NC Controlled 3 HP (2.2 kW) air cooled 12,000 RPM horizontal "Case Lock" router spindles with ERC 32 collets, RH rotation. -- (2) NC Controlled 2 HP (1.5 kW) air cooled 12,000 RPM vertical "Hardware" router spindles with ERC 32 collets, RH rotation.Operator & Machine Control: -- Separate control console with: "ADTECH CNC 4640" Controllers touch screen control with numerical and function keyboard. -- Monitor displays programming graphics, machine data & subroutines; runs production programs while programming and editing. -- Programming storage for (30) individual programs. -- Includes: Owner’s Manual with mechanical & electrical schematics and parts breakdown; covered by a 1-Year Factory Warranty on parts.Available Options at additional cost (when ordered with machine from the factory): -- Additional 0.5 HP (0.37 kW), 12,000 RPM air-cooled "Hinge Plate" router spindles with ERC 32 collets at ...$ 1,976.00 each. -- Engineered & Manufactured by COMEVA S.L, in Spain.

COMEVA NICRON CNC Door Machining Center: Flexible Door Machining Center to machine Hinges, Locks, Grooves, etc. A device to allow machining of door jambs is an option available. Also vertical top router head with Automatic Tool Changer is available. See options below.Specifications: -- Max. door length, X-Axis 102.3" (2,600 mm). -- Max. door width, Y-Axis 47.2" (1,200 mm). -- Max. travel on Z-Axis 7.87" (200 mm)Working Heads: -- The machine is equipped with a (2) motors/heads 5 HP (3.5 kW) - 12,000 RPM each, routing/milling units: (1) vertical unit and (1) horizontal double spindle head.Working table: -- Table dimensions: 51.2" x 102,3" (1,300 x 2,600 mm). -- Manual table loading system with vacuum cup hold-down for the doors. For the optional jamb (door frame) table fixturing includes an air cylinder clamping system.Operator & Machine Control: -- Separate mobile control panel with powerful CNC to handle all the functions of the machine. -- Includes the unique COMEVA DOOR Software specially designed for machining of doors. It controls the movements of all axes, reference stops, vacuum zones and workgroups. It is user-friendly with macros(subroutines) for most of the hinges/locks on the market so operator can input the job parameters instead of complicated programs.Complete with: -- Users operator/maintenance manuals & back up disks.Engineered & Manufactured by COMEVA S.L, in Spain. - Stated price includes Machine (Jamb device not included), Software and Safety Barrier.Includes: Owner’s Manual with schematics; covered by a 1-Year Factory Warranty on parts.