This BRIGHTLINE 532 mm Alignment Laser will work well on a variety of machines, and on dark surrfaces shows up better than the common Red line. -- The 5 mW Green line shows four to five times more visable to the human eye than an equally Powered Red line. -- The output power is 5 mW; 100º fan angle. -- Expected life 3,000 - 5,000 hours. -- Projection type (dot/line/cross): Dot. -- Package includes: Alignment Laser mounted in a block, Mounting bracket and power supply. This light can also be powerd by direct 3.0 VDC (300 - 800 mA draw). -- Laser beam thickness at aperture is 3 mm with a divergence of 0.1 mm for every meter of beam length. This is a focus adjustable laser with an operating temperature of 15C - 35C.

This BRIGHTLINE 635 Mm Alignment Laser will work well on a variety of machines. It is ideal for any aplication where a highly visible line projected onto a surface is needed. -- The output power is 5 mW; 100º fan angle. -- Expected life 3,000 - 5,000 hours. -- Projection type is a line and is focus adjustable. -- Package includes: Alignment Laser mounted in a block with mounting bracket and a direct 3.0 VDC (300 - 800 mA draw) power supply. -- Line straightness better than 0.1% over full length, line divergence (beam diameter) will expand 0.3 mm for every 1 meter increase in distance from the Laser to the target surface. The beam diameter at the aperture is 4.0 mm. -- Operating temperature is -10°C to +40°C.

120" Carriage travel, 13" wide anodized aluminum sliding table w/lateral handle, 45ø tilting arbor, 13-3/4" blade cap., 4-3/4" max. depth of cut, 49" rip cut cap. -- 9 HP Main motor, (3) cutting speeds 2,800 - 4,000 & 5,600 RPM, 1 HP - 8,500 RPM scoring unit with external fine adjustment, manual height & tilt adjustment, all point slide lock, on/off switches at end of sliding table. -- Complete with: Steel overarm protection guard, outfeed table extension, rip fence w/micro-adjust, crosscut fence with (2) large stops and "goniometer" miter system; mechanical holddown clamp for multiple panels. --From seller: "This Saw though several years old has been meticulously maintained with weekly cleaning and lubrication (which are the only maintenance needed besides regular belt checks and blade changes). It operates comparably to when it was purchased new. Scoring blade adjustments are easily performed at the front facing adjustment knobs."

LEADERMAC MODEL LMC-1600M - 63"; GANG RIPSAW Specifications: -- Width capacity: 0.6"; to 63"; -- Thickness capacity: 0.4"; to 2"; (thicker material processing is available as an option) -- Up & down motor: 1 HP -- Feed motor: 15 HP HD VFD -- Feed speed, infinitely variable: 20 - 200 FPM. -- Feed direction from Right to Left is standard -- Saw Spindle HP: 150 HP, Wye-Delta low amperage soft start (larger motors are available as an option) -- Saw Spindle diameter: 3.15"; (80 mm) double keyed -- Saw blade Diameter 12"; diameter for 2"; thick material -- Spindle RPM: Std. 4,000 RPM. 5,000 RPM optional with 10"; Blade capacity Standard Features & Equipment: -- Extra Heavy Main Frame – Stress Relieved -- Sound & Safety enclosure included – with internal strobe-free lighting -- High Precision Spindle - Double Keyed assembly with Hydro-Loc outboard bearing assembly on outboard side -- Entire Spindle assembly slides out on support for Quick, Easy and Precision Saw Setting & Changing -- Hardened & Hard Chromed Infeed Table -- (7) Sets of Top Power Driven Rolls – full width -- (5) Sets Bottom Power Driven Rolls – full width -- Infinitely Variable Pneumatic Pressure to Top Feed Rolls -- Top & Bottom Feed Rolls are all Driven by Cardan Shaft Drive with HD Gearboxes interconnected -- 1st Top & 1st Bottom Powered Roll Combination and then 2 Rows Anti Kick Back Finger Units – Full Width and then to the rest of the Powered Top & Bottom Rolls giving you the best Feeding Capability with good safety Features -- HD VFD – 15 HP Feed System – Infinitely Variable -- Main motor has Wye-Delta low amperage soft start -- Electrics are 460 volts 3/60 with all controls to CSA/UL Specifications -- Documentation: Maintenance manual, Operation manual, Electrical diagrams, Parts list & Tool Box (Electronic Version on Request) -- (8 - 4) Top & (4) Bottom 6"; Dust hoods included -- Saws, Dado Heads &/or cutter head(s) and spacers are optional at extra cost.Price Includes: -- Pedestal for all controls, on a 11 meter long cable to get around the front right (infeed side) of the ripsaw -- Moveable Main Electrical Panel with 10 ft. (3m) of main cable -- 150HP Saw Arbor Spindle motor in lieu of std. 75HP -- Pneumatic hold over on infeed table to hold wide, and allow holding over of narrow boards up to the fence -- Increased Feed Speed to 200FPM (60mpm) includes Heavier gearboxes and drive components) with 15 HP VFD -- Amp Meter for the Arbor Motor -- Faster removal speed for the arbor assembly (50% faster than standard machine) -- 1 Spare complete New Design Spindle Assembly including Drive Side Bearing Assembly with support slide and roller transfer support assembly per photo for preloaded saws Extended length per discussion.(1 only unit included in price of machine, this is for a 2nd cart and spindle assembly- total of (2) will come with the machine – additional units available, see below) -- Schneider / Telemecanique VFD drive uni

LEADERMAC MODEL LMC-1300M – 51"; GANG RIPSAW -- Specifications: -- Width capacity: 0.6"; to 51"; -- Thickness capacity: 0.4"; to 4"; -- Up & Down motor: 1 HP -- Feed motor: 7-1/2 HP with VFD -- Saw Spindle HP: 75 HP, larger motors are optional - see below -- Saw Spindle diameter: 3.15"; (80mm) double keyed -- Spindle RPM: Std. 4,000 RPM. 5,000 RPM optional with 10"; Blade capacity -- Saw blade Diameter 12"; diameter for 4"; thick material -- Feed speed, Infinitely variable: 20 To 50 FPM. 100 or 200 FPM optional -- Standard Features & Equipment: -- Extra Heavy Main Frame – Stress Relieved -- Sound & Safety enclosure included – with internal strobe-free lighting -- High Precision Spindle - Double Keyed assembly with Hydro-Loc outboard bearing assembly on outboard side -- Entire Spindle assembly slides out on support for Quick, Easy and Precision Saw Setting & Changing -- Hardened & Hard Chromed Infeed Table -- (7) Sets of Top Power Driven Rolls – full width -- (5) Sets Bottom Power Driven Rolls – full width -- Infinitely Variable Pneumatic Pressure to Top Feed Rolls -- Top & Bottom Feed Rolls are all Driven by Cardan Shaft Drive with HD Gearboxes interconnected -- 1st Top & 1st Bottom Powered Roll Combination and then 2 Rows Anti Kick Back Finger Units – Full Width and then to the rest of the Powered Top & Bottom Rolls giving you the best Feeding Capability with good safety Features -- HD VFD – 7.5 HP Feed System – Infinitely Variable -- Main motor has Wye-Delta low amperage soft start -- Electrics are 230, 450 or 575 volts 3/60 with all controls to CSA/UL Specifications -- Documentation: Maintenance manual, Operation manual, Electrical diagrams, Parts list & Tool Box (Electronic Version on Request) -- (4) Top & (4) Bottom 6"; Dust hoods included -- Saws, Dado Heads &/or cutterhead(s) and spacers optional extra -- Price Includes: -- Hanging Control Panel – in lieu of Control standard setup as shown in machine photo -- Moveable Main Electrical Panel with 10 ft. of main cable -- Amp Meter for the Arbor Motor -- 4"; thickness Capacity – using 12"; or 14"; diameter blades Available at extra cost: -- Adjustment of the Rear guide with digital readout from the front of the machine (only desirable if Side Heads are supplied) -- Additional Side Pressure Roller System on the Infeed Table of the Machine -- 100 HP saw spindle motor -- 125 HP saw spindle motor -- 150 HP saw spindle motor -- Scoring Saw Arbor ahead of main saws if desired -- Saw Spacers for Main Arbor quick Setup -- Mechanical Quick Lock Saw collars if desired for independent saw setting -- Spare Spindle Assembly, complete, including Drive Side Bearing Assembly with support slide and roller transfer support assembly per photo for preloaded saws, add $ 13,045 -- Questions? Call Jeff @ Ext 349!

LEADERMAC LMC-101-900 HD 36" HD Multi-Blade "Roll Feed" RIP SAWSpecifications: -- Working width: 0.6"; – 36"; -- Working thickness: 0.4"; – 4"; -- Up & Down motor: 1 HP -- Feed motor: 7-1/2 HP with VFD -- Spindle HP: 75 HP, larger motors optional -- Spindle diameter: 3.15"; double keyed -- Spindle RPM: Std. 4,000 RPM, 5,000 RPM optional -- Saw Blade Diameter, 14"; diameter -- Feed speed, infinitely variable: 20 – 50 FPM, 100 or 200 FPM optionalStandard Features: -- Extra Heavy Main Frame – Stress Relieved -- Sound & Safety enclosure included – with internal strobe-free lighting -- High Precision Spindle - Double Keyed assembly with Hydro-Lock outboard bearing assembly on outboard side -- Spindle assembly slides out on support for Quick, Easy and Precision Saw Setting & Changing -- Hardened & Hard Chromed Feed Tables -- (7) Sets of Top Power Driven Rolls – full width -- (5) Bottom Power Driven Rolls – full width -- Infinitely Variable Pneumatic Pressure to Top Feed Rolls -- Top & Bottom Feed Rolls driven by Cardan Shaft Drive with HD Gearboxes Interconnected -- 1st Top & 1st Bottom Powered Roll Combination and then (2) Rows Anti Kick Back Finger Units Full Width and then to the rest of the Powered Top & Bottom Rolls provide the best Feeding Capability with excellent safety features -- HD VFD – 7-1/2 HP Feed System – Infinitely Variable -- Main motor has Wye-Delta low amperage soft start -- Electrics are 230, 450 or 575 volts 3/60 with all controls to CSA/UL Specifications -- Documentation: Maintenance manual, Operation manual, Electrical diagrams, Parts list & Tool Box (Electronic Version on Request) -- (8) Dust outlets consisting of (4) top & (4) bottom 6"; diameter dust hoods -- Saws, Dado Heads &/or cutterhead(s) and spacers optional extra Options Included In Price: -- Hanging Control Panel – in lieu of Control std. setup as shown in machine photo, Included -- Moveable Main Electrical Panel with 10 ft. of main cable, Included -- Amp Meter for the Arbor Motor, Included -- 4"; Thickness capacity in lieu of standard 2"; thickness, Included Available Options: -- To 3" Thickness Capacity – using 12"; blades, P.O.R. -- To 3"; or 4"; thickness Capacity – using 14"; blades, P.O.R. -- To 100 FPM Top Feed Speed – Infinitely Variable – 4"; Thickness Capacity, POR -- To 200 FPM Top Feed Speed – Infinitely Variable – 2"; max. Thickness, P.O.R. -- 100 HP saw spindle motor, P.O.R. -- 125 HP saw spindle motor, P.O.R. -- 150 HP saw spindle motor, P.O.R. -- Front or Rear 10 HP Side Heads (Please discuss if interested), P.O.R. -- 15 HP or 20 HP Side Head motors in lieu of 10 HP, P.O.R. -- Adjustment of the Rear guide with digital readout from the front of the machine (only desirable if Side Heads are supplied), P.O.R. -- Scoring Saw Arbor ahead of main saws if desired, P.O.R. -- Saw Spacers for Main Arbor quick Setup, P.O.R. -- Mechanical Quick Lock Saw collars if de

LEADERMAC SYC 300M Heavy Duty Roll Feed Ripsaw: Features & General Description: -- Cast Iron base with easily accessed Anchor Bolts; lift up sound enclosure with light for quieter and safer operation; Hydro-Loc Outboard Bearing System for best gang sawing shaft support, includes grease gun; HD Cardan shaft feed (chainless) drive throughout. -- (6) Full width, close coupled driven top feed rollers; (4) full width driven bed rollers; top rolls are air tensioned; variable pressure controls on top feed rolls; motorized lift to top rolls; infeed table is hard chromed with approx. 0.012"; - 0.014"; chrome. -- Easily adjusted roll holdover on the infeed table; saw spindle has motorized lift and lowering; multiple HD V-belt driven saw spindle with special HD belt tensioner; saw blades cut from below, hence better dust removal and a heavier sturdier design. -- Saws are pre-mounted on a slip-on sleeve for quick change; (3) sets of anti-kickback devices included; central lube system; pneumatic pressure controller safety switch – if air pressure to the top rolls drops below the set to run level, the feed will automatically stop. -- Controls include: VFD Control to feed speeds and Digital Speed Readout in FPM or MPM; TECO-WESTINGHOUSE main electric motor; I.E.C. – TELEMECANIQUE-SQUARE-D Electricals meet or exceed UL/CSA Standards. -- Machine is equipped with WYE-DELTA Soft-Start (low Amperage) starters & main disconnect, multiple “E-Stops" operate at low amperageSPECIFICATIONS: -- Max. thickness, 5.1"; (130 mm); Note – to 4-1/2"; with std. 14"; diameter blades; to 5.1"; with optional 16"; Blades. -- Saw sleeve usable length of 12.3"; (312 mm) - max. dist. between outside saws; minimum length material, 10"; (250 mm) – at slower speeds. -- Saw Blades with 10"; min. to 14"; max dia. x 70 mm Bore (double key), 16"; (400 mm) optional – no charge; Saw spindle with 50 mm dia. runs at 3,200 RPM; Saw sleeve – included, 70 mm OD with double keyways. - Includes (1) set of spacers. -- Main Motor – 75 HP (50, 60, or 100 HP optional); top feed rolls – rise & fall, 1 HP; Feed Drive of 7.5 HP with VFD infinitely variable speed control, 20 to 165 FPM (6 to 50 MPM) to 200 FPM – 60 MPM – optional). -- (4) 150 mm Dust collection outlets; approx. weight – net, 5,060 Lbs.; WYE-DELTA – low Amperage - Soft Start for main motor starter; electrics to UL/CSA Standards and wired to 230/460 or 575/3/60. - Note: Stock machines are with 50 HP – 460/3/60 electrics machine and can be easily and inexpensively transformed to other voltages.Optional Extras. -- 75 KVA Auto Transformer to run machine on 230/3/60 electrics, please add ...$ 2,045. -- 16"; (400 mm) Dia. blade with 5.1"; max. Thickness N/C; NOTE: – Contact us to see if stock machine has this capacity. -- Extra Saw Sleeve, add ...$ 995. -- Additional Sets of spacers for saw sleeve, P.O.R. -- 20 MW Laser & Laser Holder w/12"; Bolt o

LEADERMAC LMC 518 S 5-HEAD (B-R-L-T-B) MOULDER (FEED THROUGH): -- Specifications:Leadermac "SMARTMAC" with a working cap. of 7" x 5". -- Head sequence: Bottom 7.5 HP, right/left 15 HP, top 15 HP and bottom 10 HP motor. -- Spindle dia. 40 MM with cutter-head speed of 6,000 RPM. All spindle adjustments except 1st. bottom head with mechanical digital readouts. -- Features: Pneumatic receding chip-breaker for top spindle. Mechanical digital readout for chip-breaker and pressure element. -- Feed system: Variable speed 20 - 85 FPM, by a 4 HP motor; Short stock driven feed roller at right spindle. Side pressure roller at infeed mounted to infeed table. -- Table plates and fences hard chromed, inside fences 32 mm height for side work profiles. -- Infeed table 2 M (6'6") infeed straightening table, manual table lubricant pump. -- Equipped with: Central lubrication system, full sound & safety enclosure. -- Includes: Used cutter-heads. Operator tools & manuals. -- Electrics conform to UL/CSA & CE specifications.

MEREEN-JOHNSON 312 DC DIP CHAIN GANG RIPSAW:Specifications: -- 1 Moving Blade, -- Hydraulic pinch roller infeed.: -- 12" Arbor cap., 14" max. dia. tooling, -- 3-1/2" max. thickness, -- 30" min. length for glue joint accuracy & 22" min. for busting only; 6" throat.Equipped with:& Features -- 50 HP - 3,600 RPM TEFC Direct drive motor, arbor -- Disc brake & load meter, arbor lockout on the access door. -- Feed & chain: 3 HP Variable feed speed from 30 - 150 FPM with adjustable jam protection, -- M-J "Posi-Feed" dip bed carried on 5" pitch hardened double-V chain, "Quad Life" hardened dip cams, -- Extruded structural aluminum feed bed slats with replaceable steel-backed rubber insert strips, -- Automatic chain oiler with low-level shutoff. -- (4) 3" Dia. air loaded overhead pressure rolls; full width segmented maple -- Spring-loaded overhead pressure shoe, -- Pressure rolls & pressure shoe unit adjust with scale & pointer thickness reference; -- Anti-kickback fingers. -- (1) saw sleeve and spacerIncludes-- Blades, Sleeves, Spacers

Mereen-Johnson 424 Gang Rip sawSpecifications -- 24" Arbor cap., -- 14" max. dia. tooling, -- 3-1/2" max. manual thickness adjustment, -- 14" min. length for glue joint accuracy and 22" min. for busting only, -- 6" throat. Equipped with and Features -- 75 HP - 3,600 RPM TEFC Direct drive motor, -- 2-3/16" dia. arbor with disc brake, -- load meter and slip-off outboard bearing. -- Feed & chain: 3 HP Variable feed speed 30 to 170 FPM, -- M-J "Posi-Feed" dip bed carried on 5" pitch hardened double-V chain -- "Quad Life" hardened dip cams -- Extruded structural aluminum feed bed slats with replaceable steel backed rubber insert strips --, Automatic chain oiler. -- (4) 3" Dia. air loaded overhead pressure rolls; full width spring loaded overhead bed plate, -- Pressure rolls and bed plate unit with scale & pointer thickness reference; -- Anti-kickback finger system with (1) lower & (2) upper on infeed. -- Sound enclosure, -- (2) Upper dust hoods (1) 10" & (1) 5" dia. and (1) lower 4" dia. hood, -- Requires 3,820 CFM;Also included: -- (7) laser with mounting rack -- (2) additional arbor and lots of spacers

Mereen-Johnson 312-DC/SR2 Gang Rip Saw with Rip Navigator Scout InfeedSpecifications -- Arbor Space: 12" -- Thickness Capacity: Up to 3" (w/ 14" Blades) -- Minimum Length: 22" (30" for Glue-Joint) -- Two Shifting Blades -- 1"Minimum Net Rip Between Shifting Blades -- Machine-Mounted Laser Stand -- Arbor Motor: 50 HP, Direct-Drive -- Feed Motor: 3 HP -- Variable Speed Feed: 30 - 150 FPM -- "Posi-Feed" Friction Feed Chain w/ Aluminum Slats and Replaceable Rubber Inserts (Rubber Inserts are Brand New) -- Hardened Steel Feed Chains & Track w/ Oil Mist Lubrication -- Air-Loaded Press Rolls -- Single Lower, Double Upper Infeed Anti-Kickback Fingers w/ Single Upper OutfeedEquipped with & Features -- Rip Navigator Scout Arranged to Receive 17'-6" Maximum Length Boards from Scissors Lift Manually placed on Board Dealer ArmsIndividual Boards are Automatically Dealt onto Lateral Chains and Conveyed to a Board Stop -- Board Stop Queues Boards for Advancement to Disappearing Fence -- Automatic Adjusting Fence Positions Boards for Placement into Gang Rip Saw Fence Positioning Through Rip Navigator -- Fence Mounted Pinch Roll Feeds -- Board to Gang Rip Saw Mounted Power Table -- Voltage: 480 with Transformer (Original Voltage as built is 575) -- New Bearing in Saw Arbor -- New Rails for Scout Infeed Chains -- 5743 HOURS -- NEW IN 2013

MIDWEST AUTOMATION GS 214 Top and Bottom Glue Spreader53" Cap., top & bottom opposed glue applicator rolls, max. 3" opening, 40" pass-line height, 7-3/4" dia. grooved rubber spreading rolls. -- Rolls fitted with Teflon end seals and water tight bearings, upper elevator opening by single hand wheel on left with dial indicator; dual hand wheel opening glue film thickness adjustment. -- Galvanized collection tank; 54 FPM feed speed, top & bottom direct drive, 1.5 HP direct drive motors. -- Complete with: (2) Protection safety guards at roller in- & outfeed with safety interlocks, complies with UL & CE safety standards.

Horizontal Tilting Multi-Moulder with Verical Router System designed for curved casings, crowns, circles, ellipses and straight mouldings. -- Equipped with: (1) 1-1/4" Diameter Spindle, 6" max. width x 7" max. thickness cap., 7.5 HP spindle motor, 6,000 RPM spindle with reverse rotation, 6-1/2" max. cutting circle horizontal, 6" max. cutting circle tilted, 0° - 52° horizontal tilting arbor, hand wheel spindle height & spindle tilt adjustment. -- Variable feed speed from 0 - 30 FPM, DC feed feed motor; hand wheel adjustable thickness opening, 34" x 30" table, independently adjustable feed rollers, and mechanically adjusted fence. -- 3.25 HP, 5-speed Porter Cable router with 1/2" shank included. This allows easy insert & Channels on both straight and curved mouldings. -- Designed to use standard 4" dia. 2-knife cutterhead for 16°/60° 1/4" corrugated back knives, (1) supplied; includes operating manual & video, parts list and covered by (1) year warranty. -- Optional: ProScale digital readouts for height and tilt settings, please add $900 for each, or for the Optional 8’’ spindle and aluminum Cutter-head, please add $3,550

Designed for curved casings, crowns, circles, ellipses and straight mouldings. -- Working dimensions: 6" wide x 7" thickness capacity. -- Spindle diameter 1-1/4" with cutterhead speed of 6,000 RPM. 6-1/2" max. cutting circle in horizontal position, 6" max. cutting circle tilted. -- Feed motor 7.5 HP variable speed 0 - 30 FPM. -- Tilting of spindle head 0° - 52°. -- Includes: Hand wheel for spindle height & tilt adjustment, mechanically adjustable fence for accurate and easy positioning. Axial adjustment. Floating work table 30" x 23". -- Linear tracking system guides the work piece smoothly and directly under the cutterhead, while keeping the workpiece flat. -- Includes (1) 4" dia. corrugated cutterhead. Operating video and manual, spare parts list and (1) year warranty. -- Additional options: Proscale digital readout for height and tilt setting .... add $900.00 for each.

Automatically feeds, shapes & ejects Rosette blocks in sizes from 2-1/2" - 5" max. square blocks; 1.5 HP motor belt drives 2-7/8" spindle cutterhead @ 7,500 RPM. -- Operation: Adjustable hopper feed to side of spindle automatically indexes Rosette blocks under cutterhead up against a corner-V holding fixture with overhead spring fingers, cutterhead advances and machines Rosette, then automatically ejects block to front (hydraulic position of block and air eject cylinder). -- Features: Cutterhead equipped for standard 16°/60° corrugated back 1/4" thick knives to be ground at 0° hook angle. -- Produces up to (500) Rosettes/Hr; Rosette profiles can be ground on any profile grinder for infinitely variable design possibilities; table top unit may include base.

Automatically feeds, shapes & ejects Rosette blocks in sizes from 5-1/2" - 8" max. square blocks; 3 HP motor belt drives 4-3/4" spindle cutterhead @ 7,500 RPM. -- Operation: Adjustable hopper feed to side of spindle automatically indexes Rosette blocks under cutterhead up against a corner-V holding fixture with overhead spring fingers, cutterhead advances and machines Rosette, then automatically ejects block to front (hydraulic position of block and air eject cylinder). -- Features: Cutterhead equipped for standard 16°/60° corrugated back 1/4" thick knives to be ground at 0° hook angle. -- Produces up to (500) Rosettes/Hr; Rosette profiles can be ground on any profile grinder for infinitely variable design possibilities; table top unit may include base.

Miner 3-31 STATIONARY Board Edger -- Welded steel frame constructed with 8 inch channel and including legs -- Working height may be determined by buyer, standard is 36" -- Overall length of frame is 16 feet, bay is 31"; wide, maximum board width is 24"; -- Two Live bottom feed rolls and two overhead gravity pressure rolls -- One stationary saw collar and one hand lever shifting saw collar, each with a 12"; diameter carbide saw -- Kohler 30 HP gasoline engine with electric start and including battery and fuel tank -- Belt drive with belt guard -- Infeed and outfeed tables with dead rolls, fixed and movable laser light.

Miner 3-31 STATIONARY Board Edger -- Welded steel frame constructed with 8 inch channel and including legs -- Working height may be determined by buyer, standard is 36" -- Overall length of frame is 16 feet, bay is 31"; wide, maximum board width is 24"; -- Two Live bottom feed rolls and two overhead gravity pressure rolls -- One stationary saw collar and one hand lever shifting saw collar, each with a 12"; diameter carbide saw -- 30 HP electric motor with 480 volt 3 phase magnetic starter included -- Belt drive with belt guard -- Infeed and outfeed tables with dead rolls

Miner B-53 STATIONARY Board Edger -- Welded steel frame constructed with 6 inch channel and including legs -- Working height may be determined by buyer, standard is 36" -- Overall length of frame is 16 feet, bay is 31"; wide, maximum board width is 24"; -- Two Live bottom feed rolls and two overhead gravity pressure rolls -- One stationary saw collar and one hand lever shifting saw collar, each with a 14"; diameter split carbide saw -- 30 HP electric motor mounted on edger -- 480 volt magnetic motor starter -- Belt drive with belt guard -- Infeed and outfeed tables with dead rolls -- Laser lights aligned with each saw

MINNESOTA 24-8 Multi-Spindle Carving Machine.Specifications: -- Spindles/Capacity: (24) Spindles, 8" between centers & 72" length capacity. -- Motors: (12) 0.75 HP motors with (1) motor driving (2) spindles via flat belt. -- Features: Manual table elevation, motorized stock rotation, non-indexable head. -- Comes with: (2) Sets of carving tools (one medium and one fine). -- Includes: Tables for flat carving - to be confirmed (?).