DISA CS-4 MAXI Dust collector with Rotary Air Lock. Approx. 16,000 CFM at 8.7:1 air-to-cloth ratio; 1,725 sq. ft. of filter area, with (128) filter bags filtering to 3-micron. -- General Info: CS-4-M consists of (3) filter modules & one entrance module. -- Comes with: DISA, S56-500 Material Handling fan powered by 50 HP TEFC motor. Fan nominal rating: 16,000 CFM @ 9" SP. Fan is currently mounted on elevated support but can be installed on the ground as well. -- (3) Reverse air bag cleaning modules with motorized fans that clean the bags every (4) hours of operation automatically, each with 2 HP fan motor. A damper at inlet closes during cleaning cycle to prevent blowback. -- Complete with: Hopper bottom as collected dust is conveyed to one end where a NRS-20 Rotary Air Lock where dust is discharged into Transfer fan. Filtered air return unit, 8' support structure to allow for dumpster under Dust Collector. -- Includes: Control panel, motor starters and switches, and Explosion Panels. Material handling main fan w/motor mounted to side of base module. -- 26" diameter inlet pipe, 97" clearance under collector for dump hopper, free standing steel bolt-together structure, -- Features: Dust transfer from bottom of Rotary Air Lock to enclosed container by separate floor mounted material handling fan, approx 7.5 HP. -- Note: Pictured storage bins are not included.

DONALDSON / TORIT DWST6-5 Cartridge Dust CollectorDownflo® WorkStations (DWST) fit anywhere on the plant floor and apply NO restrictions to worker movements or visibility. The full line of WorkStations are designed specifically for those in-plant areas where dirty and/or noisy operations are out in the open—grinding, sanding, chipping, batch mixing or welding. The DWST delivers exceptional performance in metalworking, woodworking, and process applications where high filtration efficiency and ledge less construction is often a requirement. Specifications: -- (5) Module System, each with 10 HP motor, 7,000 CFM. -- (4) Ultra-Web cartridges. -- Pulse-cleaning manifolds and ventures, (2) dust drawers. -- (1) Acoustical panel per module. Louvers mounted on lower section of unit.Includes: -- (1) IEC control panel includes 460-volt motor starters, circuit protection for each motor, transformer, programmable logic controller. -- Magnehelic gauge mounted in a panel door, start/stop buttons, and a through-the-door disconnect switch. -- Pulse cleaning can be continuous or after-shift. -- All components are IEC rated. The enclosure is rated Type 12. -- 1"; Compressed Air Regulator with Filter Separator and Gauge, Black Iron Fittings, and Black Iron Piping Required for Cleaning System. -- Provides a 1"; Common Connection Point for Design Shutters to Tie into with Existing Compressed Air System.

DONALDSON / TORIT - 2DF-16, ...Cartridge Dust CollectorSpecifications: -- Holds (16) cartridge filters. -- Includes "New" AirMax Premium Media Cartridge Filters: Fire retardant. -- Total filter media area: 3,616 ft². -- Air-to-Media ratio @ 8,000 CFM is 2.2:1. -- Automatic Pulse Clean System with: Differential pressure gauge and sequencing control in enclosure. -- (2) Hopper outlets with sealing drum cover kits. -- Steel support structure. -- Includes: 20 HP Top mount, direct-drive Blower. -- Rated for 8,000 CFM. -- Electrical motor starter & controls. -- Includes: Installation/Operation/Maintenance Manuals.Sold with 6-Month Mechanical Warranty

DOOSAN DX-180 LC-3 CRAWLER EXCAVATOR w/ 42" BUCKET (DIESEL) --Specifications: 42,000 lbs; Auxiliary Hydraulics; Hydraulic Quick Coupler; Hydraulic Thumb; 24" Wide Tracks; 42" Bucket --Hours: Approx. 4,165 (Still in use; Hours will increase) --Seller States: Great machine that is job ready. --Contact Us for Competitive Leasing Options! --All equipment is advertised to the best of our knowledge and everything is sold “AS IS"; with no guarantees.#Excavator #Doosan #Construction

DOOSAN DX300LC-3 HYDRAULIC CRAWLER EXCAVATOR with 60' LONG REACH BOOM (DIESEL)Specifications: -- 200 HP Diesel Engine; Joystick Controls w/ Switchable Control Patterns; Rearview Camera; 72" Bucket, -- New Bushings & Pins in Bucket Knuckle; 33.5" Wide Tracks; Overall Width: 11' 4". --Hours: Approx. 3,471 (will increase; still in use) --Seller States: Used, in Good Working Condition; No known issues. --Contact Us for Competitive Leasing Options! --All equipment is advertised to the best of our knowledge and everything is sold “AS IS"; with no guarantees.

DOUCET MFE 300 Lateral chain feeder for moulders and optimizers -- 3'0" x 16'-0" working deck for material length 2'0" - 16'0"; width 2" to 9.5" and thickness 1/2" to 4". -- Feed system: Hydraulic variable speed 50-300 FPM with a 20 HP power unit. In-feed (4) roller accelerator; (2) top steel rollers and (2) bottom drive roller. Additional idler rollers along feed fence to support lumber during feeding. -- Chains: Transport length of lateral chain feeder 3'0". (8) strands of C2060 chains on pneumatic up/down device to release lateral pressure on board when feeding. -- Pedestal: Feeder controls mounted to pedestal with extended cable. Interface relay to stop feeder when moulder is stopped. -- Adjustments: Tool less adjustment handles for quick setups. Easy access to for thickness adjustments at front side of feeder. -- AVAILABLE OPTIONSOne (1) set of four (4) feeding wheels made of steel with hardenedsurface teeth $ 1 000.One (1) set of four (4) feeding flat wheels made of steel, 2" wide insteadof 1" for wide material feeding $ 500.One (1) set of four (4) feeding flat wheels made of steel 1" wide $ N/C.Guiding Tunnel between feeder and moulder,Standard Guiding Tunnel (4' long) $ 1 650.Standard Short Guiding Tunnel (32" long) $ 2 100.Complete Guiding Tunnel (4' long) $ 2 700.Complete Guiding Tunnel with adjustable fence (4' long) $ 3 800.Motorized Guiding Tunnel (4' long) on request.Additional chain transfer length capacity (up to a maximum of 6additional feet) For MFE-300-16 sold per foot $ 1 685. Note: More than 6 add. feet: price upon requestSteel plates between chainsFor MFE-300-16 $ 1 050.Platen chains recommended for softwood speciesFor MFE-300-16 $ 2 850.One (1) additional chain for shorter material down to $ 1 750.18" min. lengthPressurized lateral guide with roller bearing end $ 1 400.Powered lateral guide with roller and side guides on request.Custom working height on request.

DOUCET - 16-SECTION: Clamp Carrier (Hydraulic)Specifications -- (16) Sections; 8-1/2' width. -- (6) Clamps per section; (86) clamps total. -- 32" Clamp opening (rapid change) with: 2-1/2" High jaws.Complete with: -- 5 HP Hydraulic power pack and motor for rotation. -- Hydraulic clamp tightening. -- Pneumatic overhead panel flattener.NOTE: Tear down included!

DOUCET DRAWER MASTER DWM-36 36" Universal Drawer Box Assembly Clamp Specifications: Assembles drawers with Standard Finger-Type Dovetails, Sliding-Type Dovetails, Bored & Doweled Drawers, and Tongue & dado box joints. Cap. 10" H x 24" W x 36" L. Equipped with: Fixed left jaw, Manually adjustable right jaw, with Rapid set jaw opening. Double-acting pneumatic cylinders. 2-Hand push-button operation. “Quick” Mode & "Progressive Compression" mode, Operates as a jog button to allow for easy fitting of bottom panel in lateral grooves. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

DOUCET BT3-30-5-23-G-PT Return Conveyor for Edgebanders Specifications: Right-hand feed, with Left-hand return. Min. part size 4" x 12". Max. panel size (with operator assistance supporting then turning panels) 45" x 96". Equipped with: 1-1/2’ L Infeed roller conveyor section, with (5) 23-1/4” W & (2) 34-1/4” W Rollers. 34-1/4” W x 5-1/2’ L x 35” H Receiving table, with Automatic/Manual height adjustment 2". (8) 3/8” Dia. transfer belts, (3) on 3” Centers, (2) on 6” Centers, & (3) on 9” Centers. 29-1/2” W x 5-1/2’ L x 34” H Return table. 29-1/2” W x 18’ L x 34” H 3-Section Return conveyor, with 5-1/2” W x 6’ L Gravity roller conveyor side extension. All rollers 1-7/8” Dia. covered line shaft on 3” centers. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

DOUCET - 8-SECTION, ...Clamp Carrier (Hydraulic). -- (8) Sections, 8-1/2' width. -- (8) Clamps per section, (64) clamps total. -- 42" Clamp opening (rapid change) with 2-1/2" high jaws. Complete with: -- (1) Pneumatic fence w/manual valve. -- 5 HP Hydraulic power pack and motor for rotation. -- Hydraulic clamp tightening; mounted on rail. -- Pneumatic overhead panel flattener.Actual model is: SRH 08-8.5-64-42R.Note: Tear down and loading not included.

DOUCET SDM-M-30-72 Frame and Cabinet Door ClampDesigned for quick and accurate clamping & squaring of miter and regular cabinet doors.Specifications: -- 5-1/2" x 12-1/2" Min. door size, 30" x 72" max. door size. -- (1) Fixed vertical clamp, (2) mobile vertical clamps on roller bearings for effortless positioning. -- (1) Mobile horizontal clamp with a unique "gas spring" assisted lever for effortless centering; pressure is distributed with 4' dia. air cylinders. -- "Progressive Flow" clamping system @ 80 PSI; 675 Lbs of clamping pressure per clamp; operator working height adjustment.

DOUCET - DRAWER MASTER DWM-36: 36" Universal Drawer Box Assembly ClampSpecifications -- Assembles drawers with: Standard finger-type dovetails; sliding-type dovetails; bored & doweled drawers; tongue & dado box joints. -- Capacity: 10" H x 24" W x 36" L.Equipped with: -- Fixed left jaw, manually adjustable right jaw; Rapid set jaw opening. -- Double-acting pneumatic cylinders. -- 2-Hand push button operation. -- “Quick"; Mode & "Progressive Compression" mode; operates as a jog button to allow for easy fitting of bottom panel in lateral grooves.

DOUCET SRM-6 6-Section Clamp Carrier;Specifications: -- (6) Sections; 8.5' wide usable clamping width -- (8) Clamps per section (total of approx 48 clamps).with quick attach system -- 32" Opening clamps, 2-1/2" high x 4" jaw width. Complete with: -- Pneumatic panel flattener, -- 5 HP hydraulic pump for rotation drive, -- Hydraulic clamp tightener.Note: Actual model SRM-6-8.5-48-32-RTear down not included

DOUCET - RDM2: Door Master Rotary Door Clamp with (5) StationsMax. cap. of 30" x 96" per squaring assembly. -- Features: Double door clamp design; allows clamping & squaring multiple doors at one time or large doors up to 96" L. -- Machine offers: Precise & accurate squaring of stile & rail cabinet doors; with the rotating design, you can achieve high production.Equipped with: -- (5) Rotating pneumatic sections. Each section with pneumatic squaring assembly: (2) Horizontal; (4) vertical clamps. -- Push button control for: Rotation with Heavy-Duty 575 - 3-phase gearmotor drive. -- Made of 100% welded tubular steel construction.Actual model is: DOUCET "RMD2-5-30-96".

DOUCET X-45 & MP-16 Automatic Feed to Finger JointerModel "MT-10-GD" automatic feed to Finger Jointer, chain feeding system driven on the bottom and right-and-left sides, feeds boards up to 6" max. width. -- Model "X-45" right-hand Shaper section: Cap. 3/4" - 2" max. thickness, 1-1/2" - 8" max. width (with lugs on 12" centers, 6" max. width on 9" centers), 5" min. - 96" max. length. -- Equipped with: 5 HP Trim saw, 15 HP Shaper motor, PLC controls on shaper section, dual feed chain with lugs on 12" centers, 45 FPM fixed feed speed, 5 HP feed drive, PLC controlled extrusion type glue applicator with 12-gal. tank, sound enclosure and cabinet type base. Transfer to the assembly press. -- Model "MP-16" Assembly Press: 7' - 16' Max. cutoff cap., automatic cycling, 90 FPM powered infeed flat top chain with side alignment rolls to the pre-assembly tunnel. - Pieces advance through the cutoff saw to a moveable limit switch and are cut to length, 5 HP up-cut cutoff saw for continuous assembly (2" x 9" cap. with 14" blade), finished lengths are pushed out by the next piece onto material outfeed arms, PLC controlled press section, 10 HP hydraulic unit, 10,000 Lbs max. pressure. -- Includes: Stainless friction plates on assembly table, board holddown on all (4) sides, sound enclosure, cabinet type base and all protective hoods, (1) 8-bolt cutterhead with knives and setup stand. -- Approx. 8,000 linear ft./shift or more based on 12" average infeed length.

DOUCET - 16-Section: Clamp Carrier; 16-1/2' Wide(16) Sections with: 16-1/2' wide usable clamping width.Complete with: -- (12) Clamps per section (total of 192 clamps). -- 48" Opening clamps: 3-1/2" High x 4-1/2" jaw width. -- (1) Pneumatic panel flattener. -- Heavy-Duty, 5 HP hydraulic pump for rotation drive. -- (1) Hydraulic torque wrench clamp tightener.Actual model: SRH-16-16.5-19+2-48RNOTE: Tear-down not included.

DOUCET BT3-30-5-23-G-PT Return Conveyor for EdgebandersSpecifications: -- Right-hand feed, with Left-hand return. -- Min. part size 4" x 12". -- Max. panel size (with operator assistance supporting then turning panels) 45" x 96".Equipped with: -- 1-1/2’ L Infeed roller conveyor section, with (5) 23-1/4"; W & (2) 34-1/4"; W Rollers. -- 34-1/4"; W x 5-1/2’ L x 35"; H Receiving table, with Automatic/Manual height adjustment 2". -- (8) 3/8"; Dia. transfer belts, (3) on 3"; Centers, (2) on 6"; Centers, & (3) on 9"; Centers. -- 29-1/2"; W x 5-1/2’ L x 34"; H Return table. -- 29-1/2"; W x 18’ L x 34"; H 3-Section Return conveyor, with 5-1/2"; W x 6’ L Gravity roller conveyor side extension. -- All rollers 1-7/8"; Dia. covered line shaft on 3"; centers.

"NEW" Doucet RC - STOCK Gluer - Table top unit for glue applications on a smaller scale. Motorized stainless steel roller equipped with a 2 Litre capacity reservoir easily removable for clean up. -- Spread roller: Stainless steel with roller dimension 8" X 3 1/2"; speed of roller 50 FPM. -- Table top dimension: 20-1/2" x 13".

DOUCET ERS-96/RS-75/AP-508 MULTI-BLADE PANEL GROOVE/RIP SAW SYSTEM:The Doucet ERS-96/RS-75 Automated Panel GROOVE/RIP Saw System is designed to GROOVE and/or RIP panels as well as edge the sides of core materials. Ideal for plywood, OSB, MDF, HDF and other composite panels.This Line was originally designed for Engineered Flooring Blanks.ERS-96 Grooving Specifications:40 HP - 3,500 RPM belt driven saw arbor motor. Material width cap. 96" maximum. Material thickness 0.5" - 0.625" maximumGrooving pattern on 4" centers across the 96" width of panel. Depth and width of groove approx. 3/16" kerf/width by 1/8" deep.3" dia. Arbor shaft with 1.5 HP motor for motorized arbor adjustment for panel thickness. Saw arbor accessible from above for tool changes. -- Feed system:5 HP - 1,750 RPM feed motor, variable feed speed up to 75 FPM.(4) Powered bottom feed rollers & adjustable top idler pressure rolls with positive panel support during grooving operations.Top & bottom feed rollers have slip resistant urethane covered rollers, feed rollers are chain driven with air tensioning. -- Complete with:Dynamic saw arbor brake; Infeed anti-kickback fingers; Saw blade safety interlock cover; 12" dia. dust collection outlet (4,000 CFM required). RS-75 Ripping Specifications:40 HP - 3,500 RPM belt driven saw arbor motor. Material width cap. 60" maximum. Strip width cap. 2.5" minimum. Depth of cut 0.25" - 0.75" (6 - 19 mm) maximum.3" dia. Arbor shaft with 1.5 HP motor for motorized arbor adjustment for panel thickness. Saw arbor accessible from above for tool changes. -- Feed system:Doucet AP-508 Automatic panel feeder with scissor lift to automatically feed panels as needed.5 HP - 1,750 RPM feed motor, variable feed speed up to 75 FPM.(4) Powered bottom feed rollers & adjustable top idler pressure rolls with positive panel support during grooving operations.Top & bottom feed rollers have slip resistant urethane covered rollers, feed rollers are chain driven with air tensioning. -- Operator Interface: Doucet OI/HMI Control System for automatic loading & stacking with minimal human intervention other than a forklift operator to bring in new material and remove the processed parts/strips. -- Complete with:Dynamic saw arbor brake; Infeed anti-kickback fingers; Saw blade safety interlock cover; 12" dia. dust collection outlet (4,000 CFM required). -- Options Include: (1) Doucet AP-508 Automatic panel feeder with Indexing scissor lift. (1) Cross Transfer Chain Conveyor to feed panels sideways by the long edge through the Groover, max width 96". (1) Cross Transfer Chain Conveyor to feed panels short end wise through the panel RIPSAW, max. width 60" (1) Outfeed Lift Table to automatically stack ripped strips. Maximum weight of stack: approx. 5,000 LBS. -- Actual Model is DOUCET RS-75/ERS-96/AP-508