Hogs and Wood Grinders For Sale

2009 Rotochopper E256 Grinder/Shredder | 200 HP electric rotor drive motor | 50 electric hydraulics motor |

SAS SCORPION ENGINE PULLER Model SC40 DescriptionIncrease cash recovery from your recycling operationsSAS Forks Scorpion High Speed Motor Puller – Scrap Yard Engine Puller – Auto Recycling Engine Puller – Excellent for self service yards processing vehicles before crushing.Generate revenue:Process end of life vehicles in less than 60 seconds.Pull scrap engines and transmissions in 30 seconds.30% more revenue by separating metals from bodies.1000% more revenue per lb. on wire harness from engine compartment and dash.80% more visibility with a direct line of site from the operator’s window through the forks.Cycle time less than 15 seconds from park to full extension.Serviceable for long life. Replace blades in 3 hours or less.estimated only.Engineered & built for optimum performance:Engineered tough for continuous prying and durability.Hardened pins and bushings and grease-able pivot points for extended service life.Hydraulic hoses and cylinders are protected to minimize potential damage from sharp objects.Built with high strength blades and carriage skid plates for extended service.Clean up of ground debris is a snap with center plow blade.Speed is paramount in this design. Operator uses grapple from the cab, no torches, no personnel needed to hook up chains to pull or move engines. Safer, quicker and less costly removal of engines and transmissions.

Saturn Model 36x20 Slow-Speed Shredder --36" long x 20" wide chamber opening --1/2" knives. -- KYB MRH-30-SW2 hydraulic system powered by a 50-hp three-phase electric motor. --Comes equipped with stand and controls. -- Excellent for plastic, E-scrap, rubber, small tires, paper, cardboard, light metals.

SH 218D - SMW Diesel Drum Chipper - 31 1/2"dia Blade Roll, 650rpm, 2 21 1/2" T8 Blades. 1 21 1/2" T8 Bottom Blade, Feeding Inlet 12"-27", 8-9 T/hour, 19' 21" Feeding Conveyor, 32' 23" Outlet Conveyor, 200hp Motor, 4hp - 5.5hp Feeding Roll Motor, 4hp 6 Pole Outlet Motor, 2hp Oil Pump Motor. Also available in electric. Also Available: SH 218E - SMW Electric Drum Chipper - 31 1/2"dia Blade Roll, 650rpm, 2 21 1/2" T8 Blades. 1 21 1/2" T8 Bottom Blade, Feeding Inlet 12"-27", 8-9 T/hour, 19' 21" Feeding Conveyor, 32' 23" Outlet Conveyor, 147hp Motor, 4hp - 5.5hp Feeding Roll Motor, 4hp 6 Pole Outlet Motor, 2hp Oil Pump Motor.

2024 SMW MDL SH1400-600 Wood Grinder. Available in Diesel and Electric

SCHUTTE PULVERIZER COMPANY - Model 40 HZF, ...HammermillComplete with the following major components & features: -- Integrated 18", 4,000 CFM Blower. -- WEBSTER 16 Ft. Horizontal Vibrating Conveyor. -- Motor Controls. -- Main drive motor, 75 HP - 3,540 RPM. -- Hammer width is approximately 1-1/4 in. wide. -- 3-1/4" Shaft. -- 24" Dia. Rotor and a tip speed of 22,600. -- 17-1/2" Rotor width. -- 3/4" Main chamber steel. -- Factory Frame.MANUFACTURER'S STATED KEY FEATURES:&#9679 Heavy-Duty plate construction with replaceable liner plates. &#9679 Heavy-Duty grates available in a variety of sizes. &#9679 Heavy-Duty rotor assembly. &#9679 24" Dia. x 3" thick flywheel. &#9679 Built-in fan conveys material up to 50' vertically and 100' horizontally.&#9679 Reversible anvil. &#9679 2-Way reversible "raked" hammers pull wood in without feed rolls. NOTES: &#9679 The HZF Series Horizontal Trim Scrap Grinder is a high-speed, high production Grinder designed specifically for processing longer lengths of wood scrap such as rippings, edging, and trim blocks.&#9679 Available in (4) standard sizes from 10" to 36" wide.

Schutte model 280.100 Hammer Mill Includes: 125 HP Motor - 480v Includes: (3) Screens: Approx 1", 3/4", 3/8" (to be confirmed) Includes: Stand

SCHUTTE 280.100 HAMMERMILL -- Type 13100P -- Rotor 24" dia. x 48" wide -- Housing 3/4" thick -- Shaft speed 3,600 rpm -- Heavy duty, statically and dynamically balanced rotor -- (96) Standard notched heat treated hammers 3/8" thick -- Also included; two screens -- Motor 125 HP -- Applications; Planer shavings, dry wood chips, etc. etc.

SCHUTTE PULVERIZER COMPANY - Model 40 HZF, ...HammermillComplete with the following major components & features: -- Integrated 18", 4,000 CFM Blower. -- Mellott Vibrating Conveyor -- Main drive motor: 75 HP -- Hammer width approx. 1-1/4" wide. -- 3-1/4" Shaft. -- 24" Dia. Rotor and a tip speed of 22,600. -- 17-1/2" Rotor width. -- 3/4" Main chamber steel.MANUFACTURER'S STATED KEY FEATURES:&#9679 Heavy-Duty plate construction with replaceable liner plates. &#9679 Heavy-Duty grates available in a variety of sizes. &#9679 Heavy-Duty rotor assembly. &#9679 24" dia. x 3" thick flywheel. &#9679 Built-in fan conveys material up to 50' vertically and 100' horizontally.&#9679 Reversible anvil. &#9679 2-Way reversible "raked" hammers pull wood in without feed rolls. NOTES: &#9679 The" HZF Series" Horizontal Trim Scrap Grinder is a high-speed, high production Grinder designed specifically for processing longer lengths of wood scrap such as: Rippings, edging, and trim blocks. Available in (4) standard sizes from 10" to 36" wide.&#9679 Each model features a built-in fan driven off of the main mill shaft, saving energy and valuable floor space while also significantly increasing production.

SCHUTTE BUFFALO - Model WA16L, ... HammermillModel# WA16L, 3500 RPM, with filtration system and multiple grates for destruction sizes. -- Also, includes Electrical panel. --This system is apart and palletized. All you have to do is pick it up and transport it to you. -- System was in perfect working order when it was taken apart and palletized for transport. --System is perfect for destruction of computer hard drives and different types of media.

18"wide. In very good working condition, There is no power included. Works good to run waste wood thru. Call or write for info Levi Beechy E9050 Carlson Ridge Rd. Westby, WI. 54667 or Call 574 536 1646

SCHUTTE-BUFFALO 15 Series, Model 15300 Wood Grinder;Complete with the following components and features: --Carbon Steel Construction. --Rotor approximate 44" diameter x 72" wide. --Approximately 3" wide Swinging Hammers, tip speed 20,700. --Top feed, bottom discharge. --Bottom screen approximate 5040 square inch area. --Clam shell housing. --500 HP, TEFC, 3/60/460 volt, 1785 RPM drive Motor with coupling and shaft guard. --Mounted on a heavy-duty steel Factory Frame. --NOTES: Largest model of the 15 Series. &#9679 Machine weight 16,000 Lbs.

Schutte horizontal hog, replaced shaft w/ blower & motor, heavy duty design (ref #162) Call Amy for more information (928) 723-9449

Grinder. This machine is a Shutte grinder. With Webster vibratory infeed. Item #C625

Schutte Hammer Mill 40-HZF with 100HP Electric Motor. No. 172 Attached Blower.

SHRED-TECH - ST100, ...Dual Shaft ShredderNew in 2019Specifications: -- Motors: (2) 50 HP. -- Cutter width: 1.5" Approx. -- Cutting Chamber: 32" x 60". -- Control Panel. -- Mounted on stand. -- The ST-100 Industrial Shredder is a complex, heavy-duty shredder machine that features a 32"; x 60"; cutting chamber, enabling it to handle a wide range of products and bulky wastes. It can tear through tougher loads, such as wooden pallets, metals, hazardous wastes, passenger tires, and more.Once these products go through our shredder, they end up in a smaller, optimum shred size. It works with a large-duty throughput of up to 3 tons per hour, working much more efficiently for the business

SHRED-TECH - ST50, ...Dual Shaft ShredderSpecifications: -- Motors: (2) 20 HP. -- Cutter width: 1" Approx. -- Cutting Chamber: 20" x 35". -- Control Panel. -- Mounted on stand. -- Feed Hopper: 21" x 40" Opening.Can be shown under power.

SHRED-TECH - ST20, ...Dual Shaft ShredderSpecifications: -- Motor: (1) 20 HP. -- Cutter width: 3/4" Approx. -- Mounted on stand. -- Feed Hopper.

SHRED-PAX - AZ-80, ...Shredder -- Dual Shaft Shredder. -- Motors: (2) 40 HP. -- Blades: 1" Width; (26) blades total. -- Crescent Moon Ram Assist. -- Ram rebuilt. -- Loaded onto your Truck.

SHRED-PAK - 180, ...Double Shaft ShredderSpecifications: -- (2) 75 HP Motors. -- Hook Knives: 2"; (32) knives. -- Conveyor: 60" Wide x 24 ft. long for feeding or exit. -- Control Panel: 600 - 120. -- Stand.Loaded onto Truck.