Hogs and Wood Grinders For Sale

WEIMA ZM-40 Quad Shaft 4-Shaft ShredderEquipped with: -- Dual drive motors - (2) 30 HP Drive motors. -- Hopper opening measures 51" x 55.1" (1,300 x 1,400 mm); cutting chamber opening of 30" x 27.6" (762 x 700 mm). -- Rotor length of 30" (762 mm); Rotor speed 25 RPM; cutting disc 11" (280 mm) diameter. -- Complete with: -- Control Panel with soft start and 16' cable bundle. -- Note: "Quad Shaft" Shredders, unlike Dual Shaft Shredders, allow shredded material to be circulated through the cutting chamber until it is small enough to pass through the sizing screen. -- Machine weight: 5,500 Lbs.

Weima WLB 1300 Horizontal Grinder 50 HP Motor System works, not currently in use, will need main bearing replaced.

WEIMA WLK 15 Vertical Hopper-fed Low Noise Grinder Specifications: --120 HP --15"; Shaft --82 Cutters --59"; x 59"; Hopper Opening --Hydraulic Ram

WEIMA ZM-40 Quad Shaft 4-Shaft ShredderEquipped with: -- Dual drive motors - (2) 30 HP Drive motors. -- Hopper opening measures 51" x 55.1" (1,300 x 1,400 mm); cutting chamber opening of 30" x 27.6" (762 x 700 mm). -- Rotor length of 30" (762 mm); Rotor speed 25 RPM; cutting disc 11" (280 mm) diameter. -- Complete with: -- Control Panel with soft start and 16' cable bundle. -- Note: "Quad Shaft" Shredders, unlike Dual Shaft Shredders, allow shredded material to be circulated through the cutting chamber until it is small enough to pass through the sizing screen. -- Machine weight: 5,500 Lbs.

WEIMA WLK 15 Vertical Hopper-fed Low Noise Grinder Specifications: 59" x 59" Weima WLK-15 E-Rotor Shredder, 150 HP AC Motor15" Diameter RotorFilm & Fiber Rotor90 RPM Rotor Speed(63) 50MM CuttersBolt-In Cutter Holders3" Screen90" In-Feed HeightNEW Control Panel460/3/6010" Air-Veyor DischargeNew In 2007, Refurbished In 2023.NEW CUTTERSNEW CUTTER HOLDERSNEW BED KNIVESNEW BED KNIVE HOLDERSNEW RAM GUIDES - SIDES, TOP, AND BOTTOMNEW SLIP LEDGEOVER $45,000 In New WEIMA OEM Parts Installed$25,000 Spent On New Control PanelApproximate Dimensions:Shredder: 132" L x 111" W x 90" HControl Panel: 38" L x 18" W x 60" HHydraulic: 44" L x 36" W x 42" HWILL REQUIRE WIDE LOAD TRUCK

WEIMA ZM-30 Quad Shaft 4-Shaft ShredderEquipped with: Model- ZM 30 S -- Unit was used to shred wire (6,000 – 8,000 lbs per hour) --20mm screen included 25 HP x 2 --480V- 3 phase --Cutting chamber is 19"; x 27"; Hopper is 33"; x 48"; --The ZM30S is a beefed up version of the ZM 30. Unit has the same size motors, shafts and cutters as the ZM 50 but with a shorter shaft length

Manufacturers Specifications tool diameter: 100 - 300 mm tool width: max. approx. 230 mm motor / grinding disc drive: approx. 1,1 kW free angle, adjustable 15 - 35° drive for coolant pump: approx. 0,065 kW tank capacity: approx. 90 l

West Salem model 2420GR1-H wood grinder/hog 480 v Bottom discharge No screen - machine has breaking bars Disconnected and ready to ship

WSM - 2852BH, ...Heavy Duty Hammermill/Shredder. -- 200 HP - 1,165 RPM Motor -- Infeed opening size: 52" L x 28" W -- Infeed with: Feed roll, 1-1/2" teeth with 6" spacing. -- (2) Types of Hammers: One a rounded style with hard-faced tips.Machine is part of a Pallet Recycling Plant and includes: -- Pallet Feeder -- Dual Chain Conveyor. -- Vibratory Feeder. -- Inclined Oscillating Table.

MLS Number 12321010 WEST SALEM WSM5472 Horizontal Grinder -60” Millpower Shaker conveyor/finger screen – deck removed, used to meter flow of material fed by operator and reduce bed depth to make cross belt and head pulley magnets most efficient. -60” Eriez cross belt electro magnet. -Eriez 10K42 kW Silicon Rectifier incorporating: To convert 480 volt, 60 Hz, 3 phase AC to230 volt DC 10,000 watts output Normal convection cooled, full wave bridge circuit Fused AC switch Nema 3r Enclosure -Eries beefy magnet stand to support magnet and chain fall. -60” x 28’6” Slider Bed (Heavy Duty Feeder Type Conveyor) with 8’ section of stainless steel non-magnetic for Eriez cross belt magnet to perform at peak -20”x60” Dodge magnetic head pulley – installed to double up on magnets on conveyor, prior to material entering WSM grinder drag chain feed. Downstream from this is the WSM 5472bh Titan horizontal grinder. Schematics and wiring diagram can be supplied as well. WSM also supplied the chip discharge conveyor and magnetic head pulley and electrical panel with touch screen (by Emerson). Price includes dismantling and loading on buyer's truck. Manuals available for components.

Salem Hog

West Salem Machinery 2822-BH Hog 200 hp PRICE REDUCED FOR QUICK SALE

WILLIAMS - Hammer Mill: Half-round Type ConfigurationFeatures: -- 220 HP Main Drive Motor with Belt Drive; complete with Guard. -- 26"; x 12"; Input Opening. -- Powered Input Pull Rolls -- 4"; Main Shaft with Swing Hammers, approx. 3/8"; thickness -- Ratchet Lift Access Lid. -- Mounted on Steel Support Structure with Access Platform and Ladder -- Pneumatic Bottom Discharge with built-in Viewing Window in Ducting below the Hammermill (no fan included) -- Electrical Cabinet with Motor Starters -- NOTES: This machine was last utilized to break up virgin dried pulp for further processing. Already been removed from service – ready to load.

Williams 125 CJS1 Hammermill

Williams 125 HP Hammermill 230/460 3-phase

100 HP 230/460 volt 20” x 19” inlet 9” x 28” outlet no hopper

Hammer Mill. This machine is a Williams hammer mill. Item #C549

Williams Hog S/N 14482 150HP Electric Motor

Williams Hammer Hog 30 with 125HP Motor S/N 20053

MLS Number 10791295 Williams Horizontal Wood Hog 200 HP 24" wide 16 Ft vibrating conveyor With soft start