Tennoners For Sale

This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6k ROCKWELL/CRESCENT 5-Head Single Head Tenoner Equipped with: Manually-operated sliding table. (1) Top & (1) Bottom Tenon Heads, Each with 2 HP Motor, (1) Top & (1) Bottom Cope Heads, Each with 1 HP Motor, & (1) 7" Cutoff head with 1 HP Motor.

FRIULMAC - Dual-Feed, ...Double End Cut-Off SawFor squaring workpieces and for transportation to a Planer or Moulder with a straightening table.Specifications: -- 79" Max. (2,000 mm) opening from Saw to Saw. Motorized opening with LED readout on the control panel; left-hand fixed with left-hand fence line. -- Hopper Magazine - material capacity: Min. length: 7.87" (200 mm), max.: 79" (2,000 mm); width: 1-1/8" (30 mm) to 6-3/4" (170 mm); and thickness: 0.59" (15 mm) min. up to 2-3/8" (60 mm) max.; hopper stack height: 23-1/2" (600 mm).Each side is equipped with: -- (2) Trim saw motors, 5.36 HP each; saw blade dia. 9.84" (250 mm). -- Hydraulic feed drive unit: 4 HP (3 kW) motor. -- Trimming & throughput capacity: Up to (55) pieces/Min.NOTE: Voltage transformer for 600 Volts available with the machine

FRIULMAC Quadramat Single End TenonerSingle end tenoner with (4) heads with Jump cope, cope, disc sanding and disc sandingSpecifications: -- Workpiece Length: 125 - 1500mm -- Workpiece Width: 125-1500mm -- Workpiece Thickness: 13 - 40mm -- Configuration: Jump-Cope, Cope, Wheel-Sanding, Wheel-Sanding -- First Station: 7.4 HP Jump-Cope/Profiling Unit with 40mm Diameter Shaft, 6000 RPM Rotation -- Second Station: 7.4 HP Cope/Profiling with 40mm Diameter Shaft, 6000 RPM Rotation -- Thirds Station: 4.7 HP Sanding Wheel -- Fourth Station: 4.7 HP Sanding Wheel -- Variable Speed Control of Sanding Stations from 750 - 1400 RPM -- Feed Speed: 13 - 98 FPM

Gabbiani Double End Tenoner Available approx August 1, 2023 Can also be paired with a direct transfer to a [Homag DET](https://www.carolinamachinerysales.com/listings/4073344-used-2006-homag-fl20-double-end-tenoner) at the same site.

This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6j GREENLEE 5-Head Single-End Tenoner Specifications: Max. tenon length: 3-3/4" with (1) Table pass, 7-1/2" with (2) Table passes. Max. tenon thickness 5". Max. stock width 24". Equipped with: Manually-operated sliding table. (1) Top & (1) Bottom Tenon heads, (1) Top & (1) Bottom Cope heads, & (1) 7" Cutoff head. All heads with 2 HP - 3,500 RPM Direct drive motors.

This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6i GREENLEE NO. 532 5-Head Single-End Tenoner Specifications: Max. tenon length: 3-3/4" with (1) Table pass, 7-1/2" with (2) Table passes. Max. tenon thickness 5". Max. stock width 24". Equipped with: Manually-operated sliding table. (1) Top & (1) Bottom Tenon Heads, (1) Top & (1) Bottom Cope Heads, & (1) 7" Cutoff head. All heads with 1-1/2 HP - 3,600 RPM Direct drive motors.

Greenlee tennoner with 5 heads on each side. Call 800-459-2148 for more info.

(1) Hawk CNC flooring end matcher Model HKH337 12/10/5/R/25 S/N HKH337A-20150420-01 Year 01/2016 380 Volt three phase, 160 amps Max working width 2540 mm (100") Min working width 400 mm (15.7") Max working thickness 25 mm (0.98") Min working thickness 3 mm (0.118") Min workpiece length 400 mm (15.7") Feed speed 5 to 100 m/min Table passline height 44" Top gravity infeed hopper feeder fences 2-1/4" wide rubber padded table feed chains Bolt on chain dogs mounted every 15-3/4" 36" infeed load space Table passline height 37-3/4" 1st station: (Left and right hand) Adjustable height tilting tip trim saws 4.0/6.2 Kw drive motors 2nd station: (Left and right hand) adjustable height tilting bottom trim saws 4.0/6.2 Kw drive motors 3rd station: (Left and right hand) adjustable height tilting shaper spindle 4.0/6.2 Kw drive motors 4th station: (Left and right hand) adjustable height tilting shaper spindle 4.0/6.2 Kw drive motors Servo controlled 4th station axis 5th station: (Left and right hand) adjustable height tilting shaper spindle 4.0/6.2 Kw drive motors 6th station: (Left and right hand) adjustable height tilting shaper spindle 4.0/6.2 Kw drive motors Mechanical digital readouts for station set up Pneumatic pressure shoes around shaping spindles Sound and safety enclosure around all stations Lift up access hoods with inspection windows 5.5 Kw feedworks drive motors Freestanding computer operator control station Weinview color touch screen display Push button master controls (1) Outfeed mounted conveyor deck with flooring board flipper

Homag Double End Tenoner System will be available approximately August 1, 2023 Also available with a direct transfer conveyor and [Gabbiani DET](https://www.carolinamachinerysales.com/listings/4073350-used-2003-gabbiani-sqv-sqi-double-end-tenoner) currently running inline.

GB-CIS Single-end 575V / 3 Ph / 60 Hz 5” wide rubber pad conveyor Equipped with industrial motor for full power cutting and sanding capacity

PMK C 1203 Single End Coping/Tenoning Machine -- With the C-1203 Coping Machine you can run stiles first or cope first, this machine using a 5 HP motor has counter rotating spindles to insure chip free coping of either square, single profiled or double profiled parts. -- Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 9.5" wide on the C-1203. -- (2) Counter rotating spindles 1.25" diameter. -- Spindle Speed 7,000 RPM; cycle time approx. (4) seconds. -- Side Pressure Clamp to insure proper alignment with fence. -- Cutter Heads totally enclosed for Safety!

PMK C 1205 Single End Coping Machine -- With the C-1205 Coping Machine you can run your Styles first or run your cope first, this machine using a 7.5 HP motor has counter rotating spindles to insure Chip free coping of either square. -- Single profiled or double profiled parts. Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 13.5" wide on the C-1205. -- Two counter-rotating spindles 1.25" in Diameter. -- Capacity of maximum (2) cutters on stack tooling -- Spindle Speed 7,000 RPM; cycle time approx. (4) Seconds. -- Side Pressure Clamp to insure proper alignment with a fence. -- Cutter Heads totally enclosed for Safety!

1 HP tenoner Approx. 2HPsaw Approx 28" x 16" table

Progressive Systems Inc End Matcher

SCM - Concept 2000, ...Double End Tenoner.Double End Tenoner with: Jump scoring, Hogging, Shaping with stacked tooling. -- 122" Opening cap., motorized opening with keypad entry & LED readout, 12" infeed chain area in front of holddowns. -- 0" - 4" Motorized thickness opening with mechanical digital readout. -- 6" Min. width, 2-post machine. Each side equipped with: -- 1st Station: Jump scoring. -- 2nd Station: Hogging unit. -- 3rd Station: Coping head with stacked tooling capacity (manually operated). -- 4.5 HP Drive for 10 - 60 FPM variable feed speed. -- Chain dogs on 15-3/4" centers, rubber top nonmarring chain pads. -- Heavy-Duty chain links with: Needle bearings, automatic oil mist chain oiler, automatic brake on feed motor with emergency stop.Complete with: -- Upper driven holddowns with: Continuous feed belts; feed beams can be disengaged for conventional part feeding in front of dogs. -- Mobile remote control for setup; dual lead screw for traversing beam; exhaust hoods on all heads.Note: Tear down and loading not included.

SCMI Concept NT Double End Tenoner Specifications coming.

VALITON D550 Compressed Tenon Machine NOTE: Missing Cam. Equipped with: 1-1/2 HP - 1,740 RPM - 208-220/440 V Dual voltage motor.

VOORWOOD M 15A CNC Round End Tenoner & Mortiser for 45° Door --The "M15A" Miter Machine is designed to rapidly make mortise and tenon cuts at 0°, 45° Only, . Parts can be up to 1.5"; thick and up to 4"; wide, and of ANY length. --A primary application for this machine is for miter cabinet door frames. Parts can be quickly transferred from left to right. They are mortised on the left side of the machine and tenoned on the right. The machine can also mill the slots. --Specifications & Equipped with: -- The mortise station has (3) servo-controlled axes (X, Y, and Z) that are coordinated by the machine controller to achieve complex CNC motion. It is equipped with a collet-style router spindle for cutting. The tenon station uses the same X- and Y-servo-controlled axes as the mortise station and is configured for pneumatically actuated in-and-out movement along the Z-axis. The tenon station is equipped with a direct drive shaper spindle for cutting. -- -- Pneumatic clamping assemblies with non-marring urethane pads are mounted to the hold-down assembly to secure the parts during cutting and these can be adjusted to various locations over the cutting surface. -- -- M15 Miter Machine operator interface consists of a colored touch screen. For simplicity, the entire calibration, setup, and monitoring of the machine are accomplished using only four touchscreen displays. The program designs the depth and location of both the mortise and the tenon. When the design is complete, it is saved in a recipe format. Once this recipe is opened, the operation is as simple and boils down to feeding the substrate into the machine. -- -- The full-color touchscreen panel is located on the front of the machine to provide easy access for setting up or operating the machine. Clamping and shaping operations are controlled by operating lighted pushbutton switches.

This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6h WADKIN JET-3 Single End Tenoner/End Jointer Specifications: For Windows, doors, finger jointing, & stair strings. Stock type: PAR & Moulded. Max. tenon length 120 mm (4.72"). Max. stock width 150 mm (5.91"), Max. stock length: Unlimited, Max. stock thickness: 150 mm (5.91") for Rear tables, 280 mm (11.02") for Front table, & 450 mm (17.72") for Multiple tables. Vertical table adjustment 230 mm (9.06"), Horizontal table adjustment 25 mm (0.98"). Cutterhead dia. 250 - 322 mm (9.84" - 12.68"). Cutterhead speed 3,600 RPM. Max. cutting speed 4 MPM (13 FPM), Return speed 8 MPM (26 FPM). Equipped with: (3) 7” x 27-1/2” Multi-level tables, Each with Adjustable height, Fence, & (2) with 3” Dia. Pneumatic hold-downs, Allowing machining of (3) separate pairs of parts in (1) pass or All joints of window frame/sash in (2) passes. (1) Trim/hog saw & (1) 50 mm (1.97") Dia. x 240 mm (9.45") L Stackable spindle with 7.5 kW (10 HP) - 3,420 RPM Motor, with Automatic brake.

MLS Number 10684323 Wisconsin Automated Machine C-450 Tennoner Single end tennoner Automatic double head coping tennoner Model C-450 Serial: C-450-6901-00 230 volts, 3 phase, 60 Hz. Allen-Bradley and Motortronics electrical Motors are 230 volts 48 full load amps. 15.2 amps on largest motor