Woodworking Equipment For Sale

Timesavers Single Head Sander Combination Head Model 2311-45-6 Includes transformer

Timesavers Model 2331-04-334 3-Head Orbital Sander 43" Machine

TIMESAVER 237-3 IC Wide Belt Sander: 3-Head, 36" cap. - Drum, Drum, Finishing Platen. -- 1st Head: Rubber covered contact roll, 11-1/2" dia., 50 HP motor; -- 2nd Head: Finishing platen 2-1/2" 30 HP motor. -- 3rd Head: Finishing platen 2-1/2" wide, 30 HP motor. Specifications: -- 37" x 75" Abrasive belts. -- "POSI-TRAK" electronic sanding belt tracking. -- Motorized part thickness adjustment. -- 0" - 6" Opening, automatic part thickness adjustment. -- Infeed & outfeed spring loaded holddown shoes. -- Variable feed speed from 15 - 45 FPM, 5 HP feed motor.Additional Features: -- Motor load meters. -- Infeed emergency stop bar. -- Controls mounted on belt loading side. , -- Disc brakes on sanding head motors. -- 30" Infeed load area.Actual model: TIMESAVERS "237-3IC"

TIMESAVERS 150-1v Wide Belt Sander;1-Head, 50" width cap.; contact roll head with 40 HP motor; 50" x 103" abrasive belt size, air tracking, 2-1/2" max. thickness cap., adjusted by scale; variable feed speed 40 to 100 FPM; incl. in- & outfeed extension. -- Used to have a checkrail edge sanding attachment for sanding sash (no longer available), but includes (1) extra set of new conveyor belts.

TIMESAVERS 137-1 SINGLE HEAD WIDE BELT SANDERSpecifications: -- 36" Width capacity, combination sanding head with 6" dia. spiral grooved rubber contact roll. -- 1-1/2" Wide adjustable height polishing platen on slide out assembly. -- 37" x 60" Abrasive belt size.Equipped with: -- 20 HP Main motor, -- Electric eye abrasive belt tracking, and limit switch monitoring. -- 1 HP feed motor with a fixed speed of 30FPM. -- 0" - 8" manual part thickness opening of conveyor bed. -- Double infeed & outfeed rubber covered holddown rollers. Complete with: -- 18" Infeed conveyor extension, motor load meter, and safety stop bar.

Timesavers 2321-45-01 (2) Head wide Belt Sander51" Width cap, Drum, Combination HeadHead Configuration1st Head: Steel contact roll, 8" dia., 30 HP motor.2nd Head: Combination head with a rubber-covered contact roll 5-1/2" dia. and 2-1/2" wide segmented finishing platen, 25 HP motor, (2) dial indicators for contact roll height adjustment.Specifications: 52" x 103" Abrasive belts, -- "Posi-Trak" electronic tracking & pneumatic tensioning, conveyor belt feed. -- 15 - 45 FPM Variable feed speed with inverter control, -- Automatic conveyor belt tracking; -- Double in-feed & out-feed spring loaded hold-down rolls.Equipped with & Features -- 0" - 5" Max. motorized part thickness opening with automatic part thickness set-up, -- Air-operated disc brakes, -- Motor load meters, -- 14" in-feed conveyor area, -- In-feed emergency stop bar."Owner's manual included

TIMESAVERS 2311-23-1 SERIES 2300 Wide Belt SanderSpecifications: -- Heads: 1 -- Capacity: 37" -- Combination sanding head with 4" dia. contact roll & polishing platenEquipped with: -- Air-activated emergency brake -- Outboard door interlock -- Infeed emergency stop bar and emergency stop buttons on outfeed -- (1) 4" Dust outlet -- Proscale digital readout.

Dust Collection System

Reconditioned Torit 156RF10 baghouse

TORREDA TORMADEX S.A. PA-1200 Hydraulic Wood Turning Back Knife Lathe:Nicely equipped Spanish lathe with dual hydraulic tracers for making quick work of all your demanding woodturning production runs! ... Great for turning baseball bats!Specifications: -- 47" Max. between centers, 9-7/8" max. dia. without traveling steady. -- 3-1/3" Max. dia. through steady rest (larger dia. of 6.2" cap. OPTIONAL); -- High speed automatic loading, feeder accepts pieces up to 4" square. -- 4 HP Motor with (4) turning speeds, 1,200, 2,800, 3,500, and 4,550 RPM. -- (2) HIDRO "T-75" hydraulic reproducing heads with 3" stroke. -- (2) Top mounted hydraulic knives for tenon or pattern cutting (accepts form tools up to 3" wide). -- 2 HP Hydraulic pump motor with (3) carriage feed speeds. -- Features: Pressure sensitive Hydraulic tailstock with Pressure Regulating Valve needed for small, slender turnings to avoid buckling. Pre-rounding tool in front of travelling steady rest. -- Includes: Safety guard, tooling with several roughing and finishing knives.

TORREDA METOR 1600 UNIVERSAL Copy Lathe; -- Specifications: 63" (1,600 mm) Max. between centers, 9-7/8" (250 mm) max. dia. without traveling steady, 3-1/2" (90 mm) max. dia. through steady rest (larger dia. of 6-1/4" (160 mm) cap. OPTIONAL). -- Equipped with: 4 HP Motor with adjustable turning speeds, (1) HYDRO hydraulic tracing head with 3" stroke, hydraulic controlled tailstock. -- (2) Top mounted manual knives for tenon or cutting using form tools (accepts form tools up to 3" wide); 2 HP hydraulic pump motor with adjustable feed speeds. -- Actual model is HIDRO 80/12 mm. -- Includes matching knife grinder and accessories as pictured

TRAVAINI TRO 501-1A-200V "40 HP VACUUM PUMP (LIQUID RING) 11,969 Hours:40 HP Travaini liquid ring, single stage vacuum pump "TRSC 100-700/C/F". Nominal capacity 500 ACFM @ 20" HgV; max Vacuum 27" HgV. -- Pump materials:Include cast iron housing, ductile iron impeller, and stainless steel shaft. Shaft seals are carbon face with viton elastomers. -- 40 HP:200 Volt, 3-Phase, 60 Hz, TEFC monoblock assembly for direct drive, no field alignment needed. -- Sealing fluid re-circulating system includesReservoir of carbon steel with fluid level gauge and drain, high-efficiency discharge separator and oversized heat exchanger. -- High temp switchTo protect against over-temp operation. -- Suction line accessories includeInlet check valve, vacuum gauge (0 - 30" HgV), inlet filter assembly, manual unloader valve, and vacuum relief valve. -- Heat exchangerIs an air cooler type made from aluminum and extended surface fins. -- Electrical controls include:Starter/overload reset, pump running light, hour meter, hi-temp light, and terminal blocks, all mounted in a NEMA 12 cabinet.

Tri State Machinery Straight Line Rip Saw S/N 4.5.74-72

Twin City Fan Blower Air Lock Can BE Added For Additional Cost

TWIN FLOW Air Make-Up Unit 14,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 14,000 CFM @ 1.75" ESP, 10 HPTEFC motor -- BTU: 1.38 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire. -- Also available: Controls option: - Two stages for 14,000 or 7,000 CFM at extra cost of about $3,000.

TWIN FLOW Air Make-Up Unit 7,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 7,000 CFM @ 1.75" ESP, 5HP/575v/3ph/60Hz TEFC motor -- BTU: 0.68 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Motor Control: Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire.

ULTRA GL-630H Feed Through Moulder: 6-Head (B-T-R/L-T-B), "Flooring" working capacity of 12" x 6".Specifications: -- Head sequence: Bottom 25 HP, top 30 HP, right 20 HP/left 20 HP (opposing), top 25 HP, and bottom 25 HP motor. -- Spindle dia. of 1-13/16" with cutterhead speed of 6,000 RPM; all spindles with high prevision bearings. -- Auto. positioning of the left & top spindles radially; all additional spindles with digital readouts, including chipbreaker & pressure elements. -- Pneumatics on all chipbreakers, pressure elements, and holddown rollers. -- Horizontal spindles with HydroLock outboard bearings on #1, #2, #5 & #6. -- Straight jointer on spindles #5 & #6; Profile Jointers on spindles #3, #4, #5 & #6. Equipped with: -- Inverter controlled feed drive, variable speed of 26 - 260 FPM. -- Infeed table 1.2 M (4') with all table plates & fences hard chromed to RC 70. -- Machine table includes: (5) Table rollers for smooth through feed; short stick attachment for through feed on pieces down to 230 mm. -- Electrical cabinet & pedestal for machine controls separate from machine, Heavy Duty sound enclosure. -- Includes Startup training and Warranty!

UNIQUE 313 Automatic Cope and Dowel Door MachineMiters the end and drills for dowels of (2) cabinet door rails on each pass, automatic cycle for accurate & easy alignment of mitered corners.Equipped with: -- (2) 5 HP Dual-motor set for shaping w/1-1/4" spindles; (2) 1/3 HP dowel alignment drills. -- Automatic cycle with dowel hole boring for accurate alignment of mitered door corners in (15) Seconds per cycle, -- 1" Material thickness capacity, 4" max. material width, 5" max. cutter diameter. Features: -- (2) Pneumatic clamps holds material during operation for safe machining of parts, Adjustable stops for dowel drilling, Air over oil rod-less cylinder driven table. -- Staggered tables with angled fences allow (2) 1" thick parts to be machined simultaneously; digital position indicator. -- Dust Collection: (2) 5" Dust ports require approx. 1,000 CFM per spindle.Includes - Standard Finger joint shaper heads to cut miters and drill bits for doweling.

UNIQUE 2700 CNC CNC Door ShaperCNC Controlled Machining Center for Raised Panel Doors.Equipped with: -- (1) CNC controlled 5" stackable vertical spindle (max. 4 tools per stack), 7.5 HP belt driven; max. clamping thickness 2-1/2" and 6" max. cutter head diameter. -- "X" Axis of spindle travels 81" on (2) THK rails with ball screw movement, "Y" axis with 5" travel on THK rails with 5" max. workpiece overhang, "Z" axis with 5" max. travel on THK rails.Features: -- Windows based PC computer with large touch screen menu for quick set-up, new door or custom door stiles can be programed in minutes, automatic operation from one style and size of door to the next, straight raised panels & widths of stile or rail and end tenoning work the same. -- Electronic sensors measure the length of the part to be cut allowing for various width panels or rails to be shaped consecutively, once a door is pre-programmed it can be re-called.Complete with: Electronic brake on spindles, (2) 5" dia. outlets for dust collection and UNIQUE's Windows based "Raised Panel Door" Software. .

UNIQUE 250 GT2 Automatic Raised Panel Door ShaperMachine to manufacture raised panel cabinet doors with (1) operator in (2) Min.Specifications: -- Two Counter-Rotating Variable Speed Direct Drive 10 HP Shaper Motors. -- 5" of vertical stack height, capable of stacking up to (3) cutters. -- Three (3) Position Turret for quick change over between profiles. -- The change from one cutter to another is achieved via a select switch for each operation. -- Two-position pneumatic stop system positions automatically when cutters are selected -- Easy to read positioning scale allows for accurate centering of Arched panel and rail. -- Free-floating table w/pneumatic holddown has a 2-way linear movement for straight or cathedral top doors up to 55" long.Complete with: -- (1) Set of templates (998800). -- One set of tooling included. Set includes Unique 410 cope / rail cutters and 460 panel cutter with back cutter. -- Please call for other options.